Assa Abloy 3090 Instructions de montage

eForce® 150 Keyless Entry

Model 3090

Installation Instructions and User’s Guide

INSTALLATION

Important Notes

The 3090-01 is designed exclusively for

latching hardware including:

• Adams Rite 4500/4900 series deadlatches

• Adams Rite 8000 series exit devices

The 3090-02 is compatible with Adams Rite MS® Series

Deadlocks only! These units are not interchangeable.

These instructions, and the fasteners supplied, apply

to metal door applications. Other door types will

need fasteners designed for the given medium.

IMPORTANT: This product must be installed according

to all applicable building and life safety codes!

The following additional equipment is needed for installation:

• Mortise Cylinder — 1" to 1-1/2" in length range with MS cam

NOTE: 1-1/2" cylinders require a 1/8" trim ring.

Prepare the Door

1. Select proper template to match application and

create holes according to template instructions.

2. Install Rivnuts in ¼” mounting holes according

to instructions supplied in Rivnut kit.

3. Install anchor plate, with lip up, on top holes

with two (2) #10–32 x 5/8" pan head screws

include in hardware kit (Figure 1).

Prepare the Spindle

Snap spindle to proper length for the application (Figure 2).

FIGURE 1: Prepare the Door

FIGURE 2: Prepare the Spindle

1 of 8

Approved 2023-11-13

INSTALLATION

Conﬁgure for Lock Series

Model 3090-01 used with 4500/4900 Deadlatches (including 8300/8400 Exit Devices):

1. Conﬁgure supplied cam plug to match hand of door, see LHR (Figure 3) and RHR (Figure 4).

2. Insert cam plug into latch case with notch aligned to latch set screw.

3. Tighten set screw and secure with two brass cam plug screws (Figure 5).

FIGURE 3: Left Hand Reverse FIGURE 4: Right Hand Reverse FIGURE 5

Model 3090-01 for CVR application using 8500/8600 Exit Devices:

1. Install tailpiece adapter on vertical rod.

2. Fasten with Phillips screw (Figure 6).

Model 3090-01 for RIM application using 8700/8800 Exit Devices:

1. On back of exit device, remove lower screw only to free up cylinder actuator (Figure 7).

FIGURE 7

Model 3090-02 for MS® series Deadlocks:

1. Insert cam plug into lock case with notch aligned to case set screw.

NOTE: Cam Plug must be positioned below door surface.

2. Tighten set screw and secure with two brass cam plug screws (Figure 8).

FIGURE 8

FIGURE 6: Fasten with Phillips Screw

2 of 8 Approved 2023-11-13

Hand the eForce 150

1. Install handle in desired direction & secure with Set Screw from parts kit (Figure 9).

2. For Model 3090-02, skip to “Install Mortise Cylinder” section.

3. Check rotation direction in Table 1 and change as needed. Unit is shipped in the clockwise conﬁguration, viewed from the rear.

FIGURE 9

Table 1. Handing Setup for 3090-01 Version*

Device Type Left Hand Reverse Right Hand Reverse

SVR Clockwise Clockwise

Mortise Latch Counter-Clockwise Clockwise

CVR Clockwise Clockwise

RIM Counter-Clockwise Counter-Clockwise

*3090-02 cannot change rotation direction. To change rotation, use a ﬂat screwdriver to adjust the output hub located

on the back of the 3090-01 (Figure 10). Turn approximately 270° opposite the direction you want it to actuate.

Example: If the hub is rotating clockwise, turn the hub with a screwdriver 270° clockwise; the hub will then rotate counterclockwise.

Install Mortise Cylinder

See “Mortise Cylinder Replacement” section (page 7), Steps 4-6, for detailed instruction.

Install Optional RSK-3090 Kit

For applications that require a remote activation switch, plug the RSK-3090 connector into the back of the eForce 150 (Figure 11).

NOTE: Device will unlock when wires make contact through a normally open dry contact.

FIGURE 11

INSTALLATION

FIGURE 10

3 of 8

Approved 2023-11-13

INSTALLATION

Mount the eForce 150

1. Insert the proper length spindle into the output hub.

2. Slide the eForce150 onto the anchor plate; ensure spindle engages with cam plug

(Figure 12, MS 1850 conﬁguration shown).

NOTE: The eForce 150 must sit ﬂush on the door surface.

3. Secure with two (2) #10-32 x 5/8” pan head screws (Figure 13).

FIGURE 12 FIGURE 13

Install Batteries

See “Battery Replacement” section (page 6) for detailed instructions.

SETTING UP AND USING THE eFORCE 150

User Codes

NOTES

• In user mode, entries must be followed by the * key.

• Following 5 successive invalid code entries, the red LED ﬂashes once and a tone indicates that the eForce 150 will not accept entries

for 15 seconds. One tone per second sounds during this time. Refer to “Programming Information” to change default settings.

USER CODE DESCRIPTIONS

• Master Code. Used to program any code or unlock the device in any condition.

The default Master code setting (1234) must be changed before programming additional user codes.

• Emergency Code. Unlocks the device in all conditions, including low battery or “blackout”.

The default Emergency code setting (4321) must be changed prior to programming features and codes.

• Supervisor Code. Will unlock the eForce 150, including low battery conditions. Allows for programming every code except the Master code.

• Lockout Code. Enter to restrict Normal User codes (6-152) from gaining access (green LED ﬂash + two tones + two additional tones).

Enter again to cancel Lockout Mode and allow normal access (green LED ﬂash + two tones).

• Passage Code. Will cause the device to allow free ingress entry (green LED ﬂash + 3 tones). Enter a second time to return to Normal

User Mode (green LED ﬂash + 2 tones). Passage Mode operates when the battery is low and can be overridden by the Lockout code.

• Normal User Codes. Used to brieﬂy unlock the device. A correct code entry is indicated by a green LED ﬂashing once per second.

An incorrect code entry is indicated by red LED ﬂash and 3 tones. Up to 144 dierent Normal User codes may be programmed.

These codes may not be programmed until after the default Master and Emergency codes have been reprogrammed.

• One-Time User Codes. Will unlock the device one time only. A correct code entry is indicated by a green LED ﬂashing once per

second. An incorrect code entry is indicated by red LED ﬂash and 3 tones. One-Time user codes may be programmed into locations

151 and 152. These codes may not be programmed until after the default Master and Emergency codes have been reprogrammed.

4 of 8 Approved 2023-11-13

SETTING UP AND USING THE eFORCE 150

Programming Information

NOTES

• Master and Emergency Codes (default 1234 & 4321) must be reprogrammed

from the factory pre-sets before user codes may be entered.

• If the Master Code is lost, the controller’s Master and Emergency Codes may be reset to factory

defaults by pressing Reset and # for 10 seconds.

— Reset Button is on the top back of the unit, remove from door to access.

• The programming mode will exit automatically if it times out or an invalid code is entered

during programming (indicated by a red LED ﬂash and a tone).

• All codes need to be entered twice for validation during programming. If the two entered codes

do not match, the eForce 150 will exit programming mode and the previous code will remain active.

• Emergency, Lockout, and Passage codes may be singly deleted, rendering these functions

completely un-operational (they will not return to default once deleted).

• LED’s can be disabled in User Mode (PCC32) but will remain enabled in programming mode.

Yellow = programming mode. Green = successful entry. Red = input error or programming mode exited.

• Program Command Codes (PCC) are designated codes for programming speciﬁc features. See Tables 2, 3 & 4.

PROGRAMMING PROCESS

1. Hold #key until yellow LED ﬂashes three times.

2. Release #key and the yellow LED will begin to ﬂash continually.

3. Program as required. a)-d). See Tables 2, 3 & 4.

4. To continue programming, press #within 2 seconds and return to step 3b.

5. When programming sequence is complete, wait for the device to time out and return

to normal operating mode, OR press the * key to exit programming mode.

6. Wait 2 seconds before entering any code

Example: Re-program Master Code-

Hold # →1234# →51# →1# →New Master # →New Master #

Table 2. Code to Set

Code to Set

(a)

Enter Authorization

Code then #.

(b)

Enter PCC

then #.

(c)

Enter Location

then #.

(d)

Enter New Code

then #. Repeat

Master Master

1 4 to 7 digits

Emergency Master 2 4 to 7 digits

Supervisor Master 3 4 to 7 digits

Lockout Master / Supervisor 4 4 to 7 digits

Passage Master / Supervisor 5 4 to 7 digits

Normal User Master / Supervisor 6 to 150 2 to 7 digits

One-Time User Master / Supervisor 151 to 152 2 to 7 digits

5 of 8

Approved 2023-11-13

6 of 8

SETTING UP AND USING THE eFORCE 150

Table 3. Function to Set

Function to Set

(a)

Enter Authorization

Code then #.

(b)

Enter PCC

then #.

(c)

Enter Selection or Conﬁrmation

then #. (Bold is default)

Audible Feedback Master / Supervisor 31 1 (enable); 2 (disable)

Visual Feedback (LEDs) Master / Supervisor 32 1 (enable); 2 (disable)

Attempts Before Lockout Master / Supervisor 33 1 to 255 (5 attempts)

Lockout Time Master / Supervisor 34 1 to 255 (15 seconds)

Hold Open Time Master / Supervisor 44 1 to 9 (5 seconds)

Emergency Hold Open Time Master / Supervisor 46 1 to 9 (5 seconds)

Delete All User Codes Master / Supervisor 60 60

Reset All Features Master / Supervisor 72 72

Table 4. Code(s) to Delete

Code(s) to Delete

(a)

Enter Authorization

Code then #.

(b)

Enter PCC

then #.

(c)

Enter Start of Range

then #.

(d)

Enter End of Range

then #.

Delete Individual Code Master 61 3 to 150 —

Delete Range of Codes Master 62 3 to 150 4 to 150

Supervisor 6 to 150 7 to 150

Battery Replacement

NOTE: When the batteries start to get low, the eForce 150 will emit a 4 tone warning before allowing entry; if batteries are not

changed and become very low, unit will enter blackout mode. If this happens, users 6-152 will be locked out; only Master, Emergency,

and Supervisor Codes will allow access in this mode. No codes are lost during low power conditions or battery replacement.

1. Insert key into cylinder and turn 180° clockwise to release blocking plate.

CAUTION: Once loose, the battery cover is free to slide down and can fall; support with free hand to prevent this.

2. Insert included 5/64” Allen key in hole below cylinder then loosen screw two (2) full turns to release battery cover (Figure 14).

3. Unplug battery holder (Figure 15) and replace four (4) Size AA Alkaline batteries, ensuring proper polarity.

NOTE: Lithium batteries are recommended in climates reaching 20°F and below.

4. Plug battery pack into mating connector (Figure 16) then slide cover into place (Figure 16).

— If the cover gets stuck halfway up, you may need to rotate the battery holder 90°.

5. Insert included 5/64” Allen key in hole below cylinder to tighten screw and secure battery cover (Figure 14).

6. Enter a known user code to ensure the eForce 150 is functioning correctly, if not refer to “Troubleshooting” section.

FIGURE 14 FIGURE 15 FIGURE 16

Approved 2023-11-13

SETTING UP AND USING THE eFORCE 150

Mortise Cylinder Replacement

1. Remove battery cover and battery pack; see “Battery Replacement” section for details.

2. Remove the two (2) #10-32 x 5/8 screws from the inside bottom of trim (Figure 17).

3. Lift the eForce 150 up and o the mounting bracket, being careful not to lose spindle located in output hub on back of the unit.

CAUTION: There are wires connecting the housing and back plate assembly.

These must be handled with care to not cause damage.

4. Remove eight (8) #10-32 x 5/8" screws on the back of the eForce 150 (Figure 18), and gently lift back plate o housing.

5. Remove cylinder using included Cylinder Nut Tool; ﬁt new mortise cylinder into housing and secure with

supplied Cylinder Retaining Ring and tighten using Cylinder Nut Tool (Figure 19).

NOTE: Dummy cylinders cannot be used.

6. Carefully replace back plate and screws. Do not overtighten.

7. Place eForce 150 back on door in reverse order of removal.

8. Enter a known user code to ensure the eForce 150 is functioning correctly, if not refer to “Troubleshooting” section.

FIGURE 17 FIGURE 18 FIGURE 19

TROUBLESHOOTING

Green light comes on, but lever will not retract latch-bolt.

1. Check the eForce 150 body connection with lock/latch mechanism.

2. Check cylinder tailpiece length & alignment

(see installation instructions).

3. Check for proper door preparation (refer to door templates).

No lights come on when pushbuttons are depressed.

1. Ensure Visual Keypad Feedback is set to Enable (PCC 32).

2. Check battery polarity.

3. Check battery pack voltage (6V nominal).

4. Check battery pack terminal connection.

No tones sound when pushbuttons are depressed.

1. Ensure Audible Keypad Feedback is set to Enable (PCC 31).

2. Check battery polarity.

3. Check battery pack voltage (6V nominal).

4. Check battery pack terminal connection.

Factory default codes not working.

1. Perform a Reset to return all values to default;

see “Programming Information” section.

2. Reprogram Master and Emergency codes, followed by User codes.

User codes not working.

1. Ensure Lockout Code has not been entered.

2. Check battery power (operator may be in blackout

mode). See “Battery Replacement” section.

3. Check cylinder tailpiece length & alignment

(see installation instructions).

Operator stays unlocked.

1. Ensure Passage Code has not been entered.

2. Check cylinder tailpiece length & alignment

(see installation instructions).

3. Check eForce battery and connection.

4. Ensure battery cover is on, hex screw is tight

and mortise cylinder key is removed.

7 of 8

Approved 2023-11-13

eFORCE 150 USER LOG

Installation Date Door Description

Location User Name Code Notes

1MASTER

2EMERGENCY

3SUPERVISOR

4LOCKOUT

5PASSAGE

Product Speciﬁcations

Approvals

CE, FCC, IC

Wireless Frequency

2.4GHz, IEEE 802.15.4, using AES 128-bit encryption

AA Lithium

Energizer L91 Rated 1.5 VDC, 3 Ah

NOTE: Replace Battery With Energizer L91

batteries only. Use of another battery may

present a risk of ﬁre or explosion.

CAUTION: Risk of ﬁre and burns. Do not recharge,

disassemble, heat above operating temperature

or incinerate. Keep battery out of reach of

children and in original package until ready

to use. Dispose of used batteries promptly.

Battery Life

2+ years (45,000 cycles)*

*All battery life claims are approximate and based

on a set conﬁguration proﬁle. Battery performance

is based on pre-deﬁned system settings such

as battery chemistry and battery model used,

credential presentation settings (LED/buzzer),

UHF polling period, UHF status intervals, and

operations per day. Actual battery performance

will vary and depends on the factors above.

Environmental

Operating Temperature (both products)

• 14° to 140° F [-10° to 60° C]

Operating Humidity (both products)

• 0 to 93% relative humidity non-condensing

Certiﬁcations

• UL 294 Listed – Indoor Rated

• UL 294 Salt Spray Test Compliant

• Tested to IP65 (Reader Only)

• FCC Part 15 & Industry Canada Compliant

• CE RED – Radio Equipment Directive – 2014/53/EU

UL294 Performance Levels

• Destructive Attack: Level I (No Attack Test)

• Line Security: Level I (No Line Security)

• Endurance: Level IV (100,000 Cycles)

• Standby Power: Level I (No Secondary Power)

Safety and Emissions

• FCC 47CFR Part 15, subpart C

• IC RSS-102

• RSS-210

• RSS-247

• RE Directive 2014/53/EU, EN 301 489-1, EN 301 489-3,

EN 300 440, EN 300 330, EN 300 328, EN 62368-1, EN 62479

Printed in the U.S.A.

Patent pending and/or patent www.assaabloydss.com/patents

permission of Hanchett Entry Systems, Inc. is prohibited. 80-0180-307_2

adamsrite.com | 800 626 7590

techsupport.adamsrite@assaabloy.com

WARNING

FCC Statement

This equipment has been tested and found to

comply with the limits for a class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between

the equipment and receiver.

3. Connect the equipment into an outlet

on a circuit dierent from that to which

the receiver is connected.

4. Consult the dealer or an experienced

radio/TV technician for help.

Operation with non-approved equipment is likely to

result in interference to radio and TV reception. The

user is cautioned that changes and modiﬁcations

made to the equipment without the approval of

manufacturer could void the user’s authority to

operate this equipment. To comply with FCC and

Industry Canada RF radiation exposure limits for

general population, the module must be installed to

provide a separation distance of at least 20cm from

all persons and must not be colocated or operating in

conjunction with any other antenna or transmitter.

This module is labeled with its own FCC ID and

IC Certiﬁcation Number. If the FCC ID and IC

Certiﬁcation Number are not visible when the module

is installed inside another device, then the outside

of the device into which the module is installed

must also display a label referring to the enclosed

module. In that case, the ﬁnal end product must

be labeled in a visible area with the following:

Contains FCC ID: VC3-R100V3

Contains IC: 7160A-R100V3

IC Statement

This device complies with Industry Canada

license-exempt RSS standards(s). Operation is

subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation.

Conformité aux normes IC

Cet appareil est confrome avec Industrie Canada

exempt de license RSS standard(s). Son fonctionnement

est souimes aux deux conditions suivantes:

(1) cet appareil ne peut causer d’interférences, et

(2) cet appareil doit accepter toute interference, y

compris des interférences qui peuvent provoquer

un fonctionnement indésirable du périphérique.

CE Declaration of Conformity

content.assaabloyusa.com/doc/AADSS1179512&.pdf

8 of 8 Approved 2023-11-13

Autres manuels pour 3090

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Assa Abloy Serrure de porte

Assa Abloy

Assa Abloy Yale Doorman Manuel utilisateur

Assa Abloy

Assa Abloy ABLOY EL654 Manuel utilisateur

Assa Abloy

Assa Abloy Sargent PE80 Series Manuel utilisateur

Assa Abloy

Assa Abloy Sargent AD-PE8600 Manuel utilisateur

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD216-ZW3 Instructions de montage

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Manuel utilisateur

Assa Abloy

Assa Abloy effeff ANYKEY Manuel utilisateur

Assa Abloy

Assa Abloy Yale Assure Lock YRC226 Caractéristiques techniques

Assa Abloy

Assa Abloy 179A S4 Guide de l'utilisateur

Assa Abloy

Assa Abloy Lockwood Onyx 9A1A2/5PBLK Manuel utilisateur

Assa Abloy

Assa Abloy OneSystem type A Mode d’emploi

Assa Abloy

Assa Abloy Corbin Russwin CLX3361 Manuel utilisateur

Assa Abloy

Assa Abloy Hes 5200 Series Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Manuel utilisateur

Assa Abloy

Assa Abloy Securitron TSH Series Manuel utilisateur

Assa Abloy

Assa Abloy effeff ANYKEY Manuel utilisateur

Assa Abloy

Assa Abloy ML22HPH Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin ED5800 Series Manuel utilisateur

Assa Abloy

Assa Abloy Yale Essential Series Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 80 Series Manuel utilisateur

Assa Abloy

Assa Abloy Yale Delayed Egress Manuel utilisateur

Assa Abloy

Assa Abloy MSL mFlipLock standard Manuel utilisateur

Manuels Serrure de porte populaires d'autres marques

We.lock

We.lock SECBNEBL51 Manuel utilisateur

Iseo

Iseo MA1A Manuel utilisateur

ID Lock

ID Lock 150 Manuel utilisateur

Lockly

Lockly ACCESS TOUCH PRO Manuel utilisateur

iLoq

iLoq G50S Manuel utilisateur

SDC

SDC Z7835 Manuel utilisateur

ilco

ilco 452 Manuel utilisateur

Samsung

Samsung shs-h705 Manuel utilisateur

TRU-BOLT

TRU-BOLT 08102017 Manuel utilisateur

CDVI

CDVI 500-LADJ Manuel utilisateur

Igloohome

Igloohome Deadbolt 2S Metal Grey Instructions d'installation et d'entretien

eSSL

eSSL FL-300 Manuel utilisateur

JAKO

JAKO JKBTNX4 Manuel utilisateur

Dorma

Dorma MUNDUS PREMIUM GK 50 Guide de l'utilisateur

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuel utilisateur

Yale

Yale MORTISE 8800 SERIES Manuel utilisateur

Siegenia

Siegenia KFV AS3500 Manuel utilisateur

Saflok

Saflok Quantum ädesē RFID Manuel utilisateur