Assa Abloy 179A Guide de l'utilisateur

Assa AB 702031 Edition 1 Page 1 of 4

Mounting instruction

Emergency exit device Assa 179A

This mounting instruction is intended for installation of emergency exit device Assa 179A

with following ordering numbers:

815516, 815517, 815518, 815519, 815520, 815521,815522, 815523, 815524 and 815528 in

combination with Assa lock case model 710-50 with ordering number 357711.

Warning!

The safety features of this product are essential to its compliance with EN 179.

No modification of any kind, other than those described in these instructions, are permitted.

Assa takes no responsibility for products not mounted as described in these instructions or if

enclosed maintenance and operating instruction not are followed.

In compliance with EN 179 the Assa 179A is intended for use on single doors with following

size:

Product Ordering

number

Max width of

door

Max height of

door

Max weight

of door

179A 815516

815517

815518

815519

815520

1100 mm 2100 mm 100 kg

179A-2 815521

815522

815523

815524

815528

1100 mm 2100 mm 100 kg

Assa 179A must be installed together with Assas strike plate model 1487 with following

ordering numbers: 357545, 357546, 357547, 357548 and 357549.

Assa 179A can be installed together with following outside modular profile accessories:

- Round or oval cylinder with Scandinavian shape.

- Any handle suitable for Scandinavian lock case under premises that the handle do not affect

the latch door-holding properties for a door in a fire cell.

Assa AB 702031 Edition 1 Page 2 of 4

1. Use drill template 700538 and drill 4 holes

(Ø 10 mm) for the bolt through fixing.

Also drill a hole (Ø 40-42 mm) for the exit

handle.

2. Install lock case Assa 710-50 and the strike plate.

Assa AB 702031 Edition 1 Page 3 of 4

3. Ensure that the arrows of the lock case cylinder

follower points downwards (6 oclock) on both

sides.

Attach the cylinder.

NOTE! Functional disorder may occur in the

lock case if the cylinder is operated with the

cylinder followers in wrong position.

4. Put the exit spindle into the lock case with the

stop washer against the cylinder follower on the

lock case. Put the coiled spring over the exit

spindle with the narrow end towards the exit

handle.

Use two springs for 53 mm or 63 mm exit

spindle. Then the narrow ends shall than be

turned against each other.

5. Attach the accessory with four M5 screws and

outside nipples.

The attachment plate for the plastic seal strip

shall be placed in the slot on the backside of the

accessory, at the same side as the exit handle.

NOTE! Use minimum of one 3 mm distance

plate, Assa 356820, if the B- or C-measure of the

door is less than 22mm.

Assa AB 702031 Edition 1 Page 4 of 4

6. Attach the handle and cylinder accessories.

8. Attach enclosed after glowing exit label on

the exit handle. The arrow on the label shall

point in the maneuvering direction.

Attach the plastic seal strip.

7. Test the function with the dead bolt in a locked

position and by pressing the exit handle

downwards. Both dead bolt and latch shall then

retract and the door shall be possible to open.

After opening procedure the exit handle shall

easily return to its starting position.

Assa AB 702038 Edition 1 Page 1 of 1

Maintenance and operating instruction

for Emergency exit device Assa 179 A / B

Emergency exit device

Regular intervals of at least: One month

Check all fastenings, screws etc and that the exit handle operates in good order.

Open the door by pressing the exit handle downwards. Both dead bolt and latch(es) shall then

retract and the door shall be possible to open. Ensure that the latch moves freely and get a god

engagement in the strike plate when the door is closed. The exit handle shall easily return to

its starting position after closing.

If outside handle is connected, also check the re-entry function after opening by the exit

handle.

Check plastic seal strip and that the after glowing exit label is undamaged and well visible.

Replace with a new strip and/or label if necessary.

Lock case

Regular intervals of at least: Six months

Lubricate both sides of latch and dead bolt.

Use quality grease with high adhesive capacity, such as Assa Lock Grease or similar.

Strike plate

Regular intervals of at least: Six months

Lubricate the sliding surface between strike plate and latch.

Use quality grease with high adhesive capacity, such as Assa Lock Grease or similar.

The gap between door and frame shall be 1-3 mm to insure a proper function. Adjust if

necessary.

Lock cylinder

Regular intervals of at least: Six months

Cleaning and lubricating is recommended before summer and winter.

Start with use of Assa Lock Cleaner and then follow up with Assa Lock Spray for lubrication.

At high frequency use or hard environment a shorter period of maintenance is recommended.

Warning! Never use oil or graphite lubricants in a lock cylinder.

Autres manuels pour 179A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Assa Abloy Serrure de porte

Assa Abloy

Assa Abloy Code Handle Manuel

Assa Abloy

Assa Abloy Connect 50 Manuel utilisateur

Assa Abloy

Assa Abloy ML52RA Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin MP6600 Series Manuel utilisateur

Assa Abloy

Assa Abloy besam US23-0696-01 Manuel de programmation

Assa Abloy

Assa Abloy Yale nexTouch NTB610 Caractéristiques techniques

Assa Abloy

Assa Abloy Yale Assure Lock YRD620 Caractéristiques techniques

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD216 Caractéristiques techniques

Assa Abloy

Assa Abloy Pyramid Manuel utilisateur

Assa Abloy

Assa Abloy ASSA 88x Series Manuel utilisateur

Assa Abloy

Assa Abloy VERSO CLIQ V532 Manuel utilisateur

Assa Abloy

Assa Abloy ABLOY EL654 Manuel utilisateur

Assa Abloy

Assa Abloy UNILOCK LOXURY IX Manuel utilisateur

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Manuel utilisateur

Assa Abloy

Assa Abloy MSL sFlipLock drive Manuel utilisateur

Assa Abloy

Assa Abloy Sargent PE8800 Series Manuel utilisateur

Assa Abloy

Assa Abloy GARDESA Manuel utilisateur

Assa Abloy

Assa Abloy effeff 843ZY Manuel utilisateur

Assa Abloy

Assa Abloy Lockwood Standalone Manuel

Assa Abloy

Assa Abloy Yale Essential YDME 70 Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 10X Series Manuel utilisateur

Assa Abloy

Assa Abloy HES Aperio ES100-15 Manuel

Assa Abloy

Assa Abloy Corbin Russwin SN Series Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 5300 Series Manuel utilisateur

Manuels Serrure de porte populaires d'autres marques

We.lock

We.lock SECBNEBL51 Manuel utilisateur

Iseo

Iseo MA1A Manuel utilisateur

ID Lock

ID Lock 150 Manuel utilisateur

Lockly

Lockly ACCESS TOUCH PRO Manuel utilisateur

iLoq

iLoq G50S Manuel utilisateur

SDC

SDC Z7835 Manuel utilisateur

ilco

ilco 452 Manuel utilisateur

Samsung

Samsung shs-h705 Manuel utilisateur

TRU-BOLT

TRU-BOLT 08102017 Manuel utilisateur

CDVI

CDVI 500-LADJ Manuel utilisateur

Igloohome

Igloohome Deadbolt 2S Metal Grey Instructions d'installation et d'entretien

eSSL

eSSL FL-300 Manuel utilisateur

JAKO

JAKO JKBTNX4 Manuel utilisateur

Dorma

Dorma MUNDUS PREMIUM GK 50 Guide de l'utilisateur

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuel utilisateur

Yale

Yale MORTISE 8800 SERIES Manuel utilisateur

Siegenia

Siegenia KFV AS3500 Manuel utilisateur

Saflok

Saflok Quantum ädesē RFID Manuel utilisateur