Asko HG1666AD Manuel utilisateur
CONVERSION INSTRUCTION
EN (AU) (NZ)
Introduction
WARNING!
Performing of these instructions by a non-qualified engineer can lead to dangerous
situations.
•The supplier is not responsible for the consequences (the arising of a hazardous situation
and/or damage to persons or goods) caused by incorrect performance of these instructions
by engineers who are not employees of the supplier. Consequential damage arising through
inexpert performance of these instructions is not accepted.
•This conversion-set consists of original parts. Original parts are tested for suitability and safety
during the type approval of the appliance. Frequently performed batch-approvals guarantee
the quality of original parts.
•The supplier recommends, when converting an appliance to another gas type, to have this
performed by an engineer of the service department. Contact the supplier to make an
appointment with a service engineer.
•For addresses see the guarantee regulations of the appliance.
With this conversion-set you can convert your gas hob from natural gas (NG) to universal liqified
petroleum gas (ULPG). Before you start conversion, check whether your gas hob is genuinely set
to natural gas.
ToolsTools
E. Nose pliersA. Socket spanner
F. Open end spannerB. Screw driver flat
blade
G. Leakage test sprayC. Screw driver Torx
D. Screw driver cross
head
2
Conversion instruction
Contents of conversion set:
•Injectors for the burners.
•Simmer setting screws for the gas taps.
•Gaskets.
•Two data labels with the modified gas setting.
•Fiber rings for enamelled appliances.
•Silicon sealing plugs.
•Test point adaptor.
Dismantling
WARNING!
Disconnect the appliance from the power supply before you remove the drip tray! Prevent damage
of the worktop. Lay down parts of the appliance on a protected base.
1. Remove the pan supports, burner heads and burner cups. Pull off the control knobs vertically
and remove them.
2. Loosen the screws of the mounting brackets at the underside of the appliance.
3. Unscrew the screws that are holding the burners.
4. Lift the drip tray on the back of the appliance, dismount the earth wire (if applicable), and slide
the drip tray to the front.
5. Remove the drip tray.
3
Conversion instruction
Converting
For verification, you can find the values of the injector and simmer setting screws on the holder of
the injectors. The characters of the sets correspond with the characters on the label inside the lower
tray of the appliance (upper case characters for injectors and lower case characters for simmer
setting screws). The values are also indicated on the injectors and simmer setting screws. See table:
PlughH2H1cCbBaAPGas
✔
0.400.400.930.360.720.300.600.260.462.75 kPaULPG
The following sets can occur:
•Set ‘A-a’for simmer burner.
•Set ‘B-b’for semi rapid burner.
•Set ‘C-c’for rapid burner.
• ‘H1-h’,‘H2’and ‘J-j’sets for wok burner.
NOTE!
It is possible that not all the injectors in the set will be used for the conversion of your appliance.
1. Replace the injectors in the burners.
Use a socket spanner (7) for disassembling/assembling the injectors in the burners.
2. Replace the simmer setting screws in the taps.
Use a screwdriver, flat-blade 4, for disassembling/assembling of the simmer setting screw and
when necessary use pliers.
3. On the wok burner, replace the injectors for outer (H1) and inner (H2) burner using an open end
spanner (7).
4
Conversion instruction
NOTE!
The injector for the outer burner is the one at the bottom, the upper
injector is for the inner burner.
4. Install the silicon sealing plugs, marked with a letter A, B and C in the air holes of the
corresponding burners.
•If applicable (see table).
PlughH2H1cCbBaAPGas
✔
0.400.400.930.360.720.300.600.260.462.75 kPaULPG
5. Replace the fitted governor by the test point adapter.
6. Place label “Universal LPG”over the label “Natural gas”at the underside of the appliance and
in the cupboard.
Check for gas tightness and operation
When the appliance is connected to the gas supply, use leakage test spray to check the gas
tightness.
A. Check leakage of the installation:
1. Open the main gas valve.
2. Check leakage of connections by spraying leakage test spray on the connections and check
for gas tightness.
B. Check the leakage of the injectors:
1. Seal the injector.
5
Conversion instruction
NOTE!
Press and open tap with thermo electric safety device and keep it pressed down.
2. Spray leakage test spray on the connections and check for gas tightness.
3. Repeat for every burner.
Check the gas tightness with the use of a pressure pump:
1. Connect the pressure pump to the opened testpoint adaptor and close the main gas valve and
all gas taps of the appliance.
2. Increase the pressure to 150 mbar and close the tap between the pressure pump and the
pressure gauge. Check the pressure. The maximum pressure drop is allowed up to 5 mbar per
minute. After checking, open the tap between the pressure pump and the pressure gauge. Open
one of the taps and close the corresponding injector.
NOTE!
Press and open a tap with thermo electric safety device and keep it pressed down.
3. Increase the pressure to 150 mbar and again close the tap between the pressure pump and the
pressure gauge. Check the pressure. The maximum pressure loss may amount to 5 mbar per
minute.
4. Repeat for every burner.
Final assembly
1. Replace gaskets on top of the burners.
2. Place the drip tray on the appliance starting with the front side. The hooks on the front of the
drip tray must be placed under the edge of the under tray. For enamelled drip trays, do not
forget to connect the earth cable to the drip tray.
3. Install the screws around the burner to secure the drip tray. For enamelled drip trays, use new
fiber rings under the screws.
4. Tighten the screws of the brackets at the underside of the appliance.
6
Conversion instruction
Startup
1. Install the knobs, the burner parts and pan supports.
2. Check whether the appliance is connected to the correct type of gas and gas pressure.
3. Open the main gas valve and insert the plug into the power socket.
4. Check the flame image of the burners. Refer to the 'Checking operation' section at the back of
this manual.
Check the correct operation of the burners
Important for this is that:
•The flame does not smother in simmer rate.
•The flames are not ‘blowing off’at maximum rate (recognizable by flames that are far away from
the burner in combination with a 'hissing' sound).
•Check the flame image of the burners. Refer to the 'Checking operation' section at the back of
this manual.
7
Conversion instruction
Flame pattern using LPG or Propane gas
Flame pattern using Butane gas
In contrast to propane gas, conversion to butane gas will result in a more yellow flame pattern
(yellow tipping). Yellow tipping is customary and safe and has no negative impact on
combustion, use etc.
8
Checking operation
567972-a1
Autres manuels pour HG1666AD
1
Table des matières
Autres manuels Asko Plaque
Asko
Asko HG1666AD Manuel utilisateur
Asko
Asko SIVK6FTS Manuel utilisateur
Asko
Asko HI16611 Manuel utilisateur
Asko
Asko HG1935AB Manuel utilisateur
Asko
Asko HI1655G Manuel utilisateur
Asko
Asko HG1825AB Manuel utilisateur
Asko
Asko HG8640BGB Series Manuel utilisateur
Asko
Asko HG1145AD Manuel utilisateur
Asko
Asko IG9571MB Manuel utilisateur
Asko
Asko HG1ABE3A Manuel utilisateur
Asko
Asko H4 Manuel utilisateur
Asko
Asko HIHD854GF Manuel utilisateur
Asko
Asko HG1ADE3A Manuel utilisateur
Asko
Asko HG1986SB Manuel utilisateur
Asko
Asko HG1355gd Manuel utilisateur
Asko
Asko HI1655M Manuel utilisateur
Asko
Asko HG1615ab Manuel utilisateur
Asko
Asko HIHM934M Manuel de la liste des pièces
Asko
Asko HG1666A Manuel utilisateur
Asko
Asko HG1675sb Manuel utilisateur
