Ashley AF700 Guide de démarrage rapide

THIS MANUAL INCLUDES INSTALLATION AND OPERATION INSTRUCTIONS FOR THE MODEL AF700

FURNACE UTILIZING THE LISTED OPERATIONAL TYPES:

1. WOOD ADD-ON

2. WOOD ONLY

OWNER’S INSTALLATION AND OPERATION MANUAL

MODEL AF700

Installation is to be preformed by a

qualiﬁed installer.

SAVE THESE INSTRUCTIONS

This unit is certiﬁed UL 391

United States Stove Company

227 Industrial Park Rd.

South Pittsburg, TN 37380 852426C-3203E

U.S. Environmental Protection Agency

Certiﬁed to comply with 2015 particulate emissions

standards.

CAUTION:

The warm air supply outlet of the supplementary furnace shall not be connected to the cold-air return inlet

of the central furnace because a possibility exists of components of the central furnace overheating and

causing the central furnace to operate other than as intended.

Power source not controlled by furnace main disconnect.

Respect all local and national codes when installing this unit.

This unit is not to be connected to a chimney ﬂue serving another appliance.

This unit is designed to burn solid hardwood only.

38.39

26.07

1.97

33.63

28.01

40.73

Combustible : Wood

Flue Pipe Diameter : 6” (153cm)

Flue Pipe Type: (Standard Single Wall or Double Wall): Black or Blued Steel 2100°F (650°C) Class “A”

Minimum Chimney Height : 12’

Maximum Log Length : 22”

Electrical 120V, 60Hz, 1.8A per blower (5.6A on start up)

Dimensions

Combustion Chamber :

Width x Depth :

18.5” x 22” (469mm x 558mm)

Volume :

Cubic Feet:

3.6 cubic feet

Door Opening : Width x Height: 13.6” x 9.8” (345mm x 248mm)

Pyroceramic Glass Door : (Viewing) Width x Height: 13” x 10.75” (330mm x 273mm)

Weight (lbs): 470

SPECIFICATIONS

CONGRATULATIONS!

You’ve purchased a heater from North America’s oldest manufacturer of wood burning products.

By heating with wood you’re helping to CONSERVE ENERGY!

Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least

one tree each year. Future generations will thank you.

SAFETY

Do not operate with fuel loading or ash removal doors open.

Do not connect this unit to a chimney ﬂue serving another appliance.

Danger: Risk of ﬁre or explosion. Do not burn garbage, gasoline, naphtha, motor oil, or other inappropriate

materials. Do not use chemicals or ﬂuids to start the ﬁre.

Warning: Risk of ﬁre. Do not operate with ﬂue draft exceeding .060” water column/14.93 Pascals. Do not operate

with fuel loading and ash removal doors open. Do not store fuel or other combustible materials within marked

installation clearances. Inspect and clean ﬂues and chimney regularly.

Caution: Hot surfaces. Keep children away. Do not touch during operation.

The heat exchanger, ﬂue pipe, and chimney must be cleaned regularly to remove accumulated creosote and

ash. Ensure that the heat exchanger, ﬂue pipe, and chimney are cleaned at the end of the heating season to

minimize corrosion during the summer months. The appliance, ﬂue pipe, and chimney must be kept in good

condition. These instructions also apply to a draft inducer if used. To prevent ﬂame or smoke spillage, the slide

bafﬂe must be pulled out and the fuel loading door left cracked for 10 seconds prior to opening door fully.

Load fuel carefully or damage may result.

Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

Do not use chemicals or ﬂuids to ignite the ﬁre.

Do not leave the furnace unattended when the door is slightly opened.

Do not burn garbage, ﬂammable ﬂuid such as gasoline, naphtha or motor oil.

Always close the door after the ignition.

Consult your municipal building department or ﬁre ofﬁcials about permits, restrictions and installations requirements

in your area.

INSPECT FLUE PIPES, FLUE PIPE JOINTS, AND FLUE PIPE SEALS REGULARLY TO ENSURE THAT SMOKE AND FLUE GASES

ARE NOT DRAWN INTO, AND CIRCULATED BY, THE AIR-CIRCULATION SYSTEM.

CAUTION: CLEAN OUT OF THE HEAT EXCHANGER, FLUE PIPE CHIMNEY, AND DRAFT INDUCER, IF USED, IS ESPECIALLY

IMPORTANT AT THE END OF THE HEATING SEASON TO MINIMIZE CORROSION DURING THE SUMMER MONTHS,

CAUSED BY ACCUMULATED ASH.

UNPACKING AND PRE-ASSEMBLY

UNPACKING

1) Remove all packaging from the furnace.

2) Remove the supplied tools and parts from the furnace.

A) The supplied ash shovel and poker from the heat exchanger tube, behind the heat exchanger door at

the top of the unit.

BRICK ALIGNMENT

Inspect for any damage. Ensure that the bricks and ash grate are positioned correctly and not broken (see

illustration for proper brick arrangement).

TOOLS AND MATERIALS NEEDED FOR INSTALLATION

The following is a list of tools and materials needed to install your furnace.

• 7/16” socket wrench.

• 5/16” socket (Best if using a power drill and a socket bit).

• Pair of pliers or channel-locks.

• Power drill with an 1/8” drill bit to install sheet metal screws into connector pipe..

• Sheet metal screws.

• Non-combustible ﬂoor protector as speciﬁed in this manual.

• All chimney and chimney connector components required for your particular venting installation..

• Electrical wiring tools and supplies.

• Ductwork for supply and return air.

PROPER FIRE BRICK ALIGNMENT

FURNACE INSTALLATION

Dimension Inch mm

A Backwall to Furnace 29 737

B Sidewall to Furnace 15 381

C Sidewall to Flue 18 458

D Backwall to Flue 18 458

E Supply Duct (ﬁrst 6 feet) 6 153

F Supply Duct (after ﬁrst 6 feet) 1 26

G Minimum Duct height 8 204

INSTALLATION OPTIONS

The installation of this furnace includes supplying electrical power, return (fresh air) ductwork, and supply air

ductwork. This furnace may be installed in two different conﬁgurations.

1) Stand alone wood furnace

2) Add-on wood furnace

See kit installation section in this manual to ensure proper assembly, installation and operation of your new

furnace.

If installing in an area with a fan it should not be allowed to create negative pressure in the room where the

furnace is installed.

LOCATING YOUR FURNACE (INSURE THAT THE REQUIRED MAINTENANCE CLEARANCES ARE MAINTAINED)

Your furnace must be installed as shown in this manual and in compliance with all local and national codes.

It is of the utmost importance that the clearances to combustible materials be strictly adhered to during installation

of the furnace. Refer to the table and diagrams below for minimum required clearances.

Back wall / Arrière Mur

Ceiling / Plafond

Back wall / Arrière Mur

Side wall / Paroi Latérale

CLEARANCE TO COMBUSTIBLES

MAINTENANCE CLEARANCES

Your furnace has recommended minimum maintenance clearance requirements. These clearances insure that

there is adequate room to preform maintenance and service your furnace. DO NOT store fuel within the speciﬁed

clearances. The clearances will change depending on what kits are installed with your furnace. See the tables

and diagram below to determine the clearances for your furnace.

Standard unit (no additional kits)

Dimension Inch mm

H Maintenance

Clearance (Front)

24 610

J Maintenance Clearance (Left) 10 254

K Maintenance

Clearance (Right)

10 254

L Maintenance

Clearance (Rear)

29 737

Unit with Blower Kit

Dimension Inch mm

H Maintenance

Clearance (Front)

24 610

J Maintenance Clearance (Left) 24 610

K Maintenance

Clearance (Right)

24 610

L Maintenance

Clearance (Rear)

36 915

MAINTENANCE CLEARANCE

Dimension Inch mm

M* Front 22 558.8

N Flue rear 2 51

P** Left 8 204

Q** Right 8 204

R Flue Side 2 51

FLOOR PROTECTOR REQUIREMENTS

FLOOR PROTECTOR

The furnace must be placed on solid concrete, solid masonry, or when installed on a combustible ﬂoor, on a

ﬂoor protector. The ﬂoor protector is required to provide heat, live ember, and ash protection and must be of a

non-combustible, continuous solid surface to protect against inﬁltration of live embers and ash. Floor protection

must have and R-Value of at least 1.03. Refer to ﬂoor protector manufacturer’s instructions for installation directions.

The ﬂoor protector or non combustible ﬂoor must extend under the furnace and beyond each side as shown below.

DUCTWORK INSTALLATION

We strongly recommend that the hot air ductwork be installed by a home heating specialist. If doing the installation

yourself, before you decide which installation will best suit your needs, consult a qualiﬁed heating technician and

follow his recommendations as to the safest and most efﬁcient method of installation.

This furnace can be installed in three ways, as a stand alone unit, parallel, and in series with an existing furnace.

SUPPLY AIR (HOT AIR) PLENUM

The warm-air supply duct shall be constructed of metal in accordance with NFPA 90B, 2-1.1. The plenums installed

to the furnace shall be constructed of metal in accordance with NFPA 90B, 2-1.3.

When installing this furnace the hot air plenum is to have a minimum height of 24” (610mm) if the top of the ﬁrst

vertical section is not ﬂush with the top of the ﬁrst horizontal section of ductwork. If the top of the plenum is ﬂush

with the top of the ﬁrst horizontal section of ductwork then the minium height is 15” (381mm).

RETURN AIR (FRESH AIR)

The return (fresh) air intake on the furnace is on the rear of the unit. The ductwork must be mechanically attached

to the unit or blower kit box with sheet metal screws to ensure a proper operation.

26.25

6.12

SUPPLY AIR (HOT AIR)

DUCTWORK OUTLET SIZE

SUPPLY AIR PLENUM

MINIMUM HEIGHT OF 24”

SUPPLY AIR PLENUM WITH

MINIMUM HEIGHT OF 15”

STAND ALONE INSTALLATION

If installing this furnace as a stand alone unit, ensure all local codes and all instructions in this manual are followed,

including clearance to combustibles, ﬂoor protector speciﬁcations and safety warnings.

PARALLEL FURNACE INSTALLATION

To install the new furnace in parallel with an existing furnace follow the instructions for series installation with a

few additional requirements listed below.

The return air will duct directly to the return of the new furnace, and not be pulling through any other furnace.

The output of the existing furnace must be equal to or greater than this wood furnace.

If installing in a parallel conﬁguration the ductwork may need adjustments so as to maintain the static pressure

between 0.2” W.C. And 0.05” W.C.

A back ﬂow damper must be installed in the supply ductwork of the new furnace, to ensure that air does not

circulate back through the wood furnace.

Some installation conﬁgurations may require dampers to be installed in the supply ductwork of both furnaces.

CENTRAL INSTALLATION

ADD-ON INSTALLATION

Autres manuels pour AF700

Table des matières

Autres manuels Ashley Poêle à bois

Ashley

Ashley AC2000 Manuel utilisateur

Ashley

Ashley AP5000 Manuel d'exploitation et d'entretien

Ashley

Ashley AW2020E-P Manuel d'exploitation et d'entretien

Ashley

Ashley AW2020E-P Manuel d'exploitation et d'entretien

Ashley

Ashley AW180Bli Manuel utilisateur

Ashley

Ashley AP5617 Manuel d'exploitation et d'entretien

Ashley

Ashley AW1820E Manuel d'exploitation et d'entretien

Ashley

Ashley AW3200E-P Manuel d'exploitation et d'entretien

Ashley

Ashley AP5660L Manuel utilisateur

Ashley

Ashley AW40 Manuel utilisateur

Ashley

Ashley AW1120E-P Manuel d'exploitation et d'entretien

Ashley

Ashley C60-F Instructions générales

Ashley

Ashley Ashley AP5660PE Manuel utilisateur

Ashley

Ashley AWC31 Manuel utilisateur

Ashley

Ashley AWC21 Manuel utilisateur

Ashley

Ashley AW100E Manuel utilisateur

Ashley

Ashley AC2000 Manuel utilisateur

Ashley

Ashley AW40 Manuel d'exploitation et d'entretien

Ashley

Ashley BEC95 Manuel utilisateur

Ashley

Ashley AW1120E-P Manuel d'exploitation et d'entretien

Ashley

Ashley AW40E Manuel d'exploitation et d'entretien

Ashley

Ashley AP5660L Manuel utilisateur

Ashley

Ashley AC1100 Manuel utilisateur

Ashley

Ashley AF700 Guide de démarrage rapide

Manuels Poêle à bois populaires d'autres marques

Plamen

Plamen ECO MINIMAL 50 Manuel utilisateur

Austro Flamm

Austro Flamm KOKO Manuel utilisateur

RAIS

RAIS 800 Manuel utilisateur

Henley

Henley Arklow Manuel utilisateur

Jøtul

Jøtul F 500 Manuel utilisateur

Englander

Englander BLUE RIDGE 100 Manuel utilisateur

WoodPro

WoodPro WS-TS-1500 Manuel utilisateur

Contura

Contura C 586W Manuel utilisateur

Nordpeis

Nordpeis N-20 T Manuel utilisateur

Palazzetti

Palazzetti EVA Guide de configuration

Lopi

Lopi 1250 Republic Manuel utilisateur

Panadero

Panadero CAPRI 3V Manuel de programmation

RAIS

RAIS RONDO 92 Manuel utilisateur

RAIS

RAIS attika NEXO 100 GAS Manuel utilisateur

ADURO

ADURO 15-3 Guide de l'utilisateur

Pacific energy

Pacific energy SUPER 27 SPECTRUM Manuel utilisateur

Avalon

Avalon Olympic 11190 Manuel utilisateur

Ventis

Ventis HES350 Manuel utilisateur