Ashford DOUBLE TREADLE KIT Manuel utilisateur

Ashford Guarantee

Thank you for purchasing this Ashford product. In the unlikely event there is

any fault in manufacture, please contact the dealer you purchased it from. To

validate the guarantee, please go to www.ashford.co.nz/product-registration

Ashford Handicrafts Limited

415 West Street, Ashburton 7700, New Zealand

Telephone 64 3 308 9087

sales@ashford.co.nz www.ashford.co.nz

INSTRUCTIONS

DOUBLE TREADLE KIT

ASHFORD TRAVELLER SINGLE OR DOUBLE DRIVE

Tools Required: Hammer, slot screwdriver, philips (pozi) screwdriver, candlewax, Ashford Spinning Wheel Oil.

Finishing the Wood: We recommend the wood surfaces be sealed before assembly. This protects the kiln dried wood from

climatic changes and enhances its beauty. Use either the Ashford Wax Finish or the same ﬁnish as the rest of your wheel.

Assembly Sequence: Please read these instructions right through before commencing.

1. Remove from the crank:

a) the split pin with a pair of pliers

b) the O-ring with a pin or needle

c) the E-clip with a small screwdriver. Take off old con rod from the crank.

2. Remove the hub pin. Use the nail provided and a hammer. Note: on earlier models the hub pin is in the middle of the hub.

Avoid damaging the spokes. Place a ﬂat steel object such as pliers or a spanner over the nail and hammer it.

3. R

emove the crank from the wheel. On old spinning wheels use a slot screwdriver to prise the bent 1/8” diameter hub pin out.

4. Remove the wheel from the frame. Clean the bearings and wheel. Remove any ﬁbres that may have collected around the crank

5. Remove the screw securing one front leg to the base.

6. Carefully twist and pull this leg from the frame. Note: it is possible this leg will be tight in the hole due to being a ﬁrm ﬁt

when manufactured.

If it is tight:

a) Remove the other front leg (remove the screw ﬁrst)

b) Hold the spinning wheel upside down by the leg. Protect the base with a piece of wood. Then tap the base with a

hammer. Two people may be necessary for this task.

DTKTV27012014V4

7. Locate one end of the double treadle rail into the hole in the leg in the base. Place the other leg onto the other end. Push

the leg back into the base. Check the treadle rail moves freely. Hammer the leg in and secure with the screw.

8. Replace the wheel into position. Note: the hub pin is on the same side as the con rods.

9. Push the double treadle crank (with the inner con rod attached) through the wheel supports and into the hub. There are two

holes in the crank. One will ﬁt your wheel.

10. Place the nail down the hub pin slot and rotate the crank until it ﬁts into the hole in the crank. Remove the nail and replace

it with the hub pin.

11. Slide the inner shell of the conrod universal joint onto the

crank until it clicks into the groove. Then click the front

conrod onto the universal joint on the crank.

12. Insert the front conrod into the large slot in left hand

treadle board. Hold the conrod joint with one hand on

either side of the treadle board. With both hands, turn the

conrod joint a ¼ turn. Stretch and slide it into the

small slot and turn it back a ¼ turn until it clicks into

place.Repeat the sequence for the rear conrod and the

right treadle board.

13. Lubricate all moving parts with Ashford Spinning Wheel Oil. Now you can enjoy spinning on your new Ashford Double

Treadle Kit.

Table des matières

Autres manuels Ashford Outils et accessoires de tissage

Ashford

Ashford Drum Carder Manuel utilisateur

Ashford

Ashford RIGID HEDDLE TABLE STAND Manuel utilisateur

Ashford

Ashford KNITTERS LOOM STAND Manuel utilisateur

Ashford

Ashford FOOT CONTROLLER Manuel utilisateur

Ashford

Ashford SampleIt Loom Stand Variable Width Manuel utilisateur

Ashford

Ashford SampleIt Loom Stand Manuel utilisateur

Ashford

Ashford EDC30 Manuel utilisateur

Ashford

Ashford KNITTERS LOOM STAND Manuel utilisateur

Ashford

Ashford TURBO KIT POLYCORD Manuel utilisateur

Ashford

Ashford Wild Carder Manuel utilisateur

Ashford

Ashford SPINNING CHAIR Manuel utilisateur

Ashford

Ashford KIWI 2 SPINNING WHEEL Manuel utilisateur

Ashford

Ashford WEAVING FRAME LARGE Manuel utilisateur

Ashford

Ashford WEAVING STARTER KIT Manuel utilisateur

Ashford

Ashford QUILL SPINDLE Manuel utilisateur

Ashford

Ashford DOUBLE TREADLE KIT Manuel utilisateur

Ashford

Ashford SKEINER 2 Manuel utilisateur

Ashford

Ashford Lazy Kate Super Jumbo Manuel utilisateur

Ashford

Ashford SPINNING WHEEL MAINTENANCE KIT Manuel utilisateur

Ashford

Ashford DRUM CARDER Fine Manuel utilisateur

Ashford

Ashford BALL WINDER Manuel utilisateur

Ashford

Ashford WOODEN UMBRELLA SWIFT Manuel utilisateur

Ashford

Ashford KNITTERS LOOM STAND 70cm Manuel utilisateur

Ashford

Ashford DOUBLE TREADLE KIT Manuel utilisateur

Manuels Outils et accessoires de tissage populaires d'autres marques

Beadalon

Beadalon 216S-100 Manuel utilisateur

BEKA

BEKA Yarn Swift Manuel utilisateur

Beadalon

Beadalon TOGGLE JIG Manuel utilisateur

Toika

Toika Eeva ES Manuel utilisateur

Weaver

Weaver Weaver Snap Davits Manuel utilisateur

Beadalon

Beadalon Ring Weaver Tool Manuel utilisateur

Xiamen Rizheng Industry

Xiamen Rizheng Industry Crochet Hook Kit Set Manuel utilisateur

Read Pleaters

Read Pleaters 24-Row Regular Manuel utilisateur

MOKIDA

MOKIDA ZM2642501SYL-000-000 Manuel utilisateur

Artistic Wire

Artistic Wire Findings Forms 228S-661 Manuel utilisateur