ASA Electronics T Series Manuel utilisateur
T SERIES AIR SCREWDRIVERS OPERATOR’S MANUAL
2008.01.17
For safety use, Please Follow the instructions. The operation without your local regulations may cause serious injury.
Read thoroughly and understand this instruction manual and keep this within reach for future reference.
Lever start type
Retaining ring
Air Inlet(Oil Daily)
color Ring
Valve Reverse
Regulating Handle Soft Cover
Push to start type
Bit Slide Sleeve Valve Reverse
Retaining ring
Soft Cover
Color Ring
Air Inlet(Oil Daily)
Bit Slide Sleeve
(in Torque cover) (in Torque cover)
Regulating Handle
CLASSIFIED CAPACITY SPECIFICATIONS
Fastening Capacity
Model
No.
Free
Speed
r.p.m.
Weight
g
O.A.L
mm
Dia.
mm
Air
Pressure
Kg/cm²
Min. air
hose bore
mm
Air
Consumption
m³/min
Torque
range
Kgf-cm
Standard
Deviation
%
Machine
Screw Dia.
Tapping
Screw Dia.
T10PB/T10LB 1000 558/598 194 32 6.0 5.0 0.5 0.5-2 ±3 M1.0-M2.2 M1.0-M1.7
T20PB/T20LB 1000 558/598 194 32 6.0 5.0 0.5 1-8 ±3 M1.7-M3.3 M1.3-M2.7
T30PB/T30LB 1800 558/598 194 32 6.0 5.0 0.5 2-16 ±3 M2.2-M4.2 M1.7-M3.2
T40PB/T40LB 1000 558/598 194 32 6.0 5.0 0.5 5-30 ±3 M2.8-M5.0 M2.3-M4.0
T50PB/T50LB 1400 912/953 233 38 6.0 8.0 0.65 7-50 ±3 M2.9-M6.0 M2.6-M4.9
T55PB/T55LB 1000 912/953 233 38 6.0 8.0 0.65 7-65 ±3 M2.9-M6.4 M2.6-M5.4
T60PB/T60LB 550 912/953 233 38 6.0 8.0 0.65 15-95 ±3 M4.1-M7.0 M3.3-M6.0
* LEGEND : T10 －P －B － O/E － R/A － P/G
Model NO. P:Push to start type B:for 1/4” Hex. bit Environment Right Angle Pistol Grip
L:Leverstarttype A:for5mmHex.bit protection
● OPERATIONS
1Push valve reverse button makes instantly change direction of air motor rotation.
2Push-to-Start system eliminates troublesome to press throttle lever.
3Easy adjusting fastening torque by tightening or loosening nut torque indication.
Tighten to the right : increase torque
Loosen to the left : decrease torque
4Air motor will automatically stop when the load reaches at the pre-set torque.
5Smooth depress the bit slide sleeve into the screwdriver , then you can inset bit or take out bit from screwdriver easily. Take
off retaining ring and torque cover, then you can adjust the torque value which you need.
6 Color ring：The color torque control system gives you an easily visible torque marking system at a glance for all the tools. Choice
the tools. Choice the color for each torque level used on your assembly line.
7Precision adjustment has been made around case, gear and rotating section.
8Do not attempt to disassemble under any circumstance.
● AIR SUPPLY
1. Air tools are adversely affected by moisture. Since air from compressor contains much moisture and
dust, it is desirable to provide a filter and lubricator in the pipe line to remove such undesirable elements. Also take the drain
out from air tank every day.
2. When using brand-new air hose or air pipe. Blow and clean the inside of air hose or pipe before
installation.
3. Keep inside of air hose or air pipe clean to prevent air drop problem caused by the lots of drain
and dust accumulated and possibly make the inside diameter smaller in the long use.
4. When disconnect air hose from air tool while in the operation do not drop air hose end to the floor
as dust or other element may come into air hose.
5. Use air regulator to keep stable air pressure at 6.0kg/cm²at the toll. It is important
to get proper air pressure at the toll.
6. After lubrication, oil will discharged the exhaust upon operation. Flush motor for a few seconds.
● LUBRICATION
1. Lubrication is indispensable to air tolls. The most ideal maintenance is to install one lubricator
to a toll for automatic oil feed, but if it is not available, manual lubrication twice every
day is recommended for longer life and keeping the efficient function of mechanism.
2. For manual lubrication, disconnect air hose from bushing air inlet and full up spindle
oil(#40-#60) into the air feed in take and push the bit.
3. Change the new soft cover. Put soft cover into torque indication ring then blow air into soft
cover to hold the open soft cover and push it up at the same time.
T40PB (1000rpm)
INDEX REQ'D INDEX REQ'D
NO. NO. NO. NO.
P-3404-SO-01 Backhead 1P-3404-SO-36 2mm Ball 24
P-3404-SO-02 O-Ring 2P-3404-SO-37 Washer 1
P-3404-SO-03 O-Ring 1P-3404-SO-38 Retaining Ring 1
P-3404-SO-04 Screw 1P-3404-SO-39 Slide Base 1
P-3404-SO-05 Reverse Knob 1P-3404-SO-40 Spring 1
P-3404-SO-06 Reverse Valve 1P-3404-SO-41 Spindle 1
P-3404-SO-07 Rear End Plate 1
P-3404-SO-41-1
Spring 1
P-3404-SO-08 Ball Bearing 1P-3404-SO-42 4mm Ball 2
P-3404-SO-09 Sping Pin 2P-3404-SP-43 3/32" Ball 2
P-3404-SO-10 Sping Pin 1P-3404-SO-44 Torque Setting Spring 1
P-3404-SO-11 Cylinder 1P-3404-SO-45 Washer 1
P-3404-SO-12 Rotor 1P-3404-SO-46 Bushing 1
P-3404-SO-13 Rotor Blade 5P-3404-SO-47 Clutch Housing 1
P-3404-SO-14 Front End Plate 1P-3404-SO-48 A-type Pin 4
P-3404-SO-15 Ball Bearing 1P-3404-SO-49 Washer 1
P-3404-SO-16 Rear Rotor Retainer 1P-3404-SO-50 Torque Ring 1
P-3404-SO-19 Planet Gear 4P-3404-SO-51 Spring 1
P-3404-SO-20 Rear Gear Head Assembly 1P-3404-SO-52 Release Sleeve 1
P-3404-SO-21 Main Gear 1P-3404-SO-53 Retaining Ring 1
P-3404-SO-22 Planet Gear 4P-3404-SO-54 Protective Casing 1
P-3404-SO-23 Front Gear Head Assembly 1P-3404-SO-55 Setting Protective Casing 1
P-3404-SO-24 Ring Gear 1P-3404-SO-56 Protective Casing 1
P-3404-SO-25 Housing 1P-3404-SO-57 Inlet Bushing 1
P-3404-SO-26 Grip Collar 1P-3404-SO-58 O-ring 1
P-3404-SO-27 Ball Bearing 1P-3404-SO-59 Throttle Valve Stem 1
P-3404-SO-28 Retaining Ring 1P-3404-SO-60 O-ring 1
P-3404-SO-29 Washer 1P-3404-SO-61 Throttle Valve 1
P-3404-SO-30 2mm Ball 30 P-3404-SO-62 Throttle Valve Spring 1
P-3404-SO-31 Pilot Pin 1P-3404-SO-63 Muffler Insert 2
P-3404-SO-32 Rear Clutch 1P-3404-SO-64 Exhaust Deflector 1
P-3404-SO-33 1/8" Ball 2P-3404-SO-65 Hanger 1
P-3404-SO-34 Central Clutch 1P-3404-SO-66 Color Ring 4
P-3404-SO-35 End Clutch 1
2007/02/05
DESCRIPTION DESCRIPTION
ASA-T40PB Full Auto Shut-Off Air Screwdrivers, Push To Start Type
19
20
21
23 22
02
63
41-1
65
60
64
59
61 62
58 57
56
55
54
53 52
51
50
49
48
47
46 45
44 43 42
41
40
39
26
38 37 36
35
34
33 32
31
30 29 28 27
25
24
16 15
14
13
12
11
07
10 09 08
05 04
06 03
01
66
Ce manuel convient aux modèles suivants
14
Autres manuels ASA Electronics Tournevis électrique
