ASA Electronics AS-4632S Manuel utilisateur

□ After Use Serial No. :

Storage and maintenance: if you do not plan to use the screwdriver for a long period, unplug it or

switch off the power source. Store the screwdriver in a dry, dust-free place, away from direct

sunlight. Inspect and maintain it periodically to ensure continued functioning.

ASA Industrial Electric Screwdriver User’s Manual

(for semi-automatic models-strengthened tightening torque)

Repair: If the screwdriver is not operating normally, do not attempt to disassemble it. Contact one

of our service agents.

□ Warranty

We provide a one-year free repair service warranty with this product. The warranty is good for one year

from the date of purchase entered on the Product Information Form. The retailer’s stamp must appear on the

form to confirm the date. However, under the following circumstances we will charge the user for any parts

and labor costs associated with repairs:

For repairs involving normal wear to parts including carbon brushes, bits and power cord, and also

to the exterior surface.

If the screwdriver was connected to a power source of the incorrect voltage.

After the period of the guarantee, or if the user cannot present the manual with stamped Product

Information Form.

Please note:

The retailer’s stamp must appear on the Product Information Form in order to receive free repair service.

If the date is not filled in, the guarantee takes effect from the date of product assembly.

We cannot replace this manual. Please safeguard it.

□ Other points

The adapters (optional) with many applications are available for use with this product. However, for drilling

holes, it should never be used on any material except plastic and wood less than 2mm thick, and especially

not on metal or walls.

Please note:

Drill bits may break off if the screwdriver is not held tightly or held at an angle to the drilling surface. Take

care of your hands and eyes!

HANGER

REVERSE

LEVER

CARBON

BONNET

FORWARD

LEVER

MAINTENANCE

BIT SLIDE

SLEEVE REGULATING

HANDEL

ENGRAVINR

RING

Lever start type

AS-4632S

Product Information Form

Model Retailer’s Stamp

Serial No.

Date of Purchase

◎ Specifications and design may be changed without notice for improvement(A-5)

□ AWord of Thanks to Our Customers

Thank you for choosing lightweight and powerful ASAelectric screwdrivers. In order to insure maximum

performance and product life, please read through this manual before using your screwdriver.

□ Features

Our screwdrivers were designed for fastening screws. They include many patented features:

Anti-slip egg-shaped body

Patented carbon brush cover prevents shocks

Indicator light shows when carbon brush needs replacement

Integral dual insulation

Centrifugal turbine heat dispersion

Low-noise transmission

Patented power cord clip

Screw-driving applications range from assembly of small items such as watches and eyewear to home

appliances, hardware, furniture and other products.

□ Specifications

Model AS-

1631 AS-

1632 AS-

2631 AS-

2632 AS-

3631 AS-

3632 AS-

4631 AS-

4631S AS-

4632 AS-

4632S AS-

6631 AS-

6632

Power source

ACV 115

60HZ 230

50HZ 115

60HZ 230

50HZ 115

60HZ 230

50HZ 115

60HZ 230

50HZ 115

60HZ 230

50HZ

Torque range

kgf-cm/1bf-in 0.2-2.0/0.17-1.7 0.5-7.0/0.43-6.1 1.0-12.0/0.9-10.4 2.0-18.0/1.7-15.6 5.0-25.0/4.3-21.7

No load speed rpm 1000 1000 1000

1000 1800 1000 1800 1000

Torque setting

Machine Screw

mm/in 1.0-2.0/0.04-0.08 1.0-2.6/0.04-0.10 1.4-3.0/0.06-0.12 2.0-4.0/0.08-0.16 2.6-5.0/0.10-0.20

Available

Screw

Tapping Screw

mm/in 1.0-1.7/0.04-0.07 1.0-2.3/0.04-0.09 1.4-2.6/0.06-0.10 2.0-3.0/0.08-0.12 2.3-4.0/0.09-0.16

Weight g/1b 400/0.88 480/1.0

Length mm/in 228/9.0

Available bit shank ψ4.0 ψ5.0/5mm Hex shank , 1/4’’Hex shank, 1/4’’Hex double end shank

Power consumption W 30 40

□ Outline

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

Push bit slide

sleeve in

□ Accessories

This product comes supplied with a pair off carbon brushes and two bits.

Bits (one set per screwdriver)

Bit specifications

ψ4.0 ψ5.0 1/4" Hex shank 1/4Hex double end shank

Tip

diameter

D P# Tip

No.

Tip

diameter

D P# Tip

No.

Tip

diameter

D P# Tip

No.

Tip

diameter

D P#

Available

Screwdriver

Model

#00 ψ1.7 7W1202 #00

ψ1.7 7W6204 AS-1631

#00 ψ2.0 7W1402 #00

ψ2.0 7W6404 AS-1632

#0 ψ2.5 7W1522 #0

ψ2.5 7W6524 AS-2631

#1 ψ4.0 7W1742 #1

ψ3.0 7W6644 AS-2632

ψ3.0 7W3644 #1 ψ3.0 7W6644 #1 ψ6.35 7W7147 AS-3631

ψ5.0 7W3864 #2 ψ4.5 7W6764 #2 ψ6.35 7W7167 AS-3632

ψ3.0 7W3644 #1 ψ3.0 7W6644 #1 ψ6.35 7W7147 AS-4631

ψ5.0 7W3864 #2 ψ6.0 7W6964 #2 ψ6.35 7W7167 AS-4632/S

ψ5.0 7W3844 #1 ψ4.5 7W6744 #2 ψ6.35 7W7167 AS-6631

ψ5.0 7W3864 #2 ψ6.0 7W6964 #2 ψ6.35 7W7167 AS-6632

□ Before Using

Check voltage: Please read the label on the product exterior and the manual thoroughly before

using the screwdriver, and make especially sure to correctly determine the screwdriver’s voltage

requirement (115VAC or 230VAC). Only plug the screwdriver into an outlet with the correct

voltage.

Check for suitable torque range: Choose a screwdriver model that matches your required torque

range. To lengthen product life, avoid using screwdrivers at maximum torque over long periods.

Check that product is completely assembled: Check that the carbon maintance bonnet is closed

tightly. If the bonnet or spring connector have com loose, the motor will automatically cut off-the

screwdriver will operate only after the have been correctly reassembled. If the power cord is in

any way damaged, unplug the screwdriver immediately and exchange it for a new product in order

to protect against short circuit.

Check the workplace: Although this product features dual insulation, to ensure safety do not use it

in damp or high-temperature environments, or near flammable materials. Keep the power cord

away from tools and equipment that might damage or melt it.

Caution: When plugging in or unplugging the power cord, make sure to hold it by the plug. Never

pull the power cord forcibly.

□ Usage and Cautions

Screw and unscrew settings: To drive a screw, set the forward/reverse switch to the FWD position.

To remove a screw, set the switch to the REV position (Caution! --- Never change the switch

position when the motor is running! Release the trigger (power switch) and change the position

after the motor stops.)

Torque setting: Set the torque level by rotating the regulating handle. Turning it clockwise into the

casing will increase the torque, and turning it counterclockwise out of the casing will decrease

the torque. (Caution!－The markings on the regulating handle are for reference only and do

not indicate torque output. Actual torque can only be determined with a torque testing

machine or hand-held spanner torque tester.) If you have difficulty removing screws (reverse

setting), increase torque by turning the regulating handle clockwise into the casing.

Inserting the bit: Push the bit slide sleeve down with

your finger and insert a suitable bit. When the bit slide

sleeve is released, the bit will become engaged. If the

bit slide sleeve can not homing, please pull out the bit

.Count！-please change the 3 band switch( forward ＆

reverse switch) to middle band, and don＇t beat or force

to pull out when inserting bit.

Inserting and removing single-or double-ended 1/4"

hex bits: Inserting the bit and arrive bottom, then push

the bit slide sleeve down with your finger, the will be

flip out.

Hang securely: During use the screwdriver should be hung up securely to prevent it from failing,

and also to protect the power cord from sudden pulls.

Starting and stopping the motor: Press the trigger(power switch) down to start the screwdriver,

And release it to stop.

Important points:

If the clutch slips when screws are fully tightened (i.c. Clicking sound is not heard when torque is

reached) immediately release the trigger (power switch) to prevent the motor from burning out (due

to continued power flow while it is not operating).

If the screwdriver is operating for a long period, or if excessive current surges are experienced,

the screwdriver may overheat. In this case it will switch off automatically. When the heat has

dispersed, normal operation can resume.

Operational frequency: suggest the operational frequency 1/4”(ON/OFF)second, the total screws

7000pcs/8hours, don’t over our operational frequency suggest, and avoid the inside part of

screwdriver serious damage. If everyday work 8hours upward, please use two screwdriver by turns,

protect the life of screwdrivers.

Changing the carbon brush: When the carbon brush change indicator lights up (red), please

Change it as described below. (Caution!－Always unplug the screwdriver before changing the brush.

Only use the factory-specification brushes provided with the screwdriver as replacements.)

1. Insert a slotted bit with a 3.0mm wide, 1.0mm thick head in the slot on the side of the carbon

maintance bonnet and lever it up. Open the bonnet.

2. Remove the spring resting on the carbon brush.

3. Lift the copper wire attached to carbon brush, and pull the brush out.

4. Pull out the tip of the copper wire and complete the removal.

5. Insert the new carbon brush, following the above steps in reverse order.

Position A

VIEW OF POSITION A

remove

Pull

out out

Pull

STEP 1 STEP 2 STEP 3 STEP 4

Lever

convex point

receptacle

3P plug

(screwdriver side)

Guide for 3P plug-in

Guide for carbon brush replacement

guide notch

shank

1/4" hex 1/4"

hex

double end

shank

WWW.100Y.COM.TW WWW.100Y.COM.TW WWW.100Y.COM.TW

Table des matières

Autres manuels ASA Electronics Tournevis électrique

ASA Electronics

ASA Electronics T Series Manuel utilisateur

Manuels Tournevis électrique populaires d'autres marques

Makita

Makita DFT085F Manuel utilisateur

Parkside

Parkside 345138 2004 Manuel utilisateur

Makita

Makita DFL650F Manuel utilisateur

AEG

AEG BST 18BLX2-0 Manuel utilisateur

Ingersoll-Rand

Ingersoll-Rand D5000 Series Manuel utilisateur

BGS technic

BGS technic 956 Manuel utilisateur

Hilti

Hilti SD 6000 Manuel utilisateur

Parkside

Parkside PEPS 3 A1 Manuel utilisateur

Festool

Festool TI 15 Manuel utilisateur

Makita

Makita DWT190 Manuel utilisateur

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Manuel utilisateur

Skil

Skil 2346 Instructions de montage

DeWalt

DeWalt XR LI-ION DCD931 Manuel utilisateur

Festool

Festool DWC 18-2500 Manuel utilisateur

EINHELL

EINHELL TE-CD 12/1 Li Series Manuel utilisateur

Makita

Makita BFT043F Manuel utilisateur

Stanley

Stanley SCD2 Manuel utilisateur

Atlas Copco

Atlas Copco LUM12 SR Feuille d'instructions