Artesyn MATXM-CORE-411-WR Manuel utilisateur
MATXM-CORE-411-WR
Quick Start Guide
P/N:6806800L45B (September 2014)
Observe ESD-safe
measures
What’s in the box?
Install the processor
When installing or servicing the module or
accessories, strictly observe the safety
precautions in the Safety Notes. Other-
wise, personal injury or property damage
may occur.
• Use either a properly grounded ESD wrist
strap or make sure that you are working
in an ESD-safe environment.
• Connect to the ESD connector at the
front or the rear of the system.
Make sure you receive all items of your shipment:
• One MATXM-CORE-411-WR
• One printed copy of Quick Start Guide (this
document)
• One printed Safety Notes Summary
• Motherboard
• Midplane
•CPU
• CPU cooler
• Memory module
• Cables
• IO shield
• Driver CD
• USB sticks
• Any other optional items ordered
Prepare the installa-
tion site
• For information on the environmental
and power requirements, see the
MATXM-CORE-411-B Installation and Use
manual.
• The MATXM-CORE-411-B must be in
good condition, without defects such
as oxidation, chemical corrosion, missing
components, or transportation damage.
• Confirm the position where the MATXM-
CORE-411-B will be installed.
1. Take the processor out of the antistatic pack-
age.
2. If a processor is currently installed, open the
socket actuator using a screwdriver, and
then remove the processor.
3. Check the bottom of the new processor to
make sure that there is no shortage or dam-
age of the PGA pin.
4. Align the arrow on the Pin A1 of the new pro-
cessor with the arrow on the socket, and
then close the socket actuator with a screw-
driver while gently holding the processor
down with your finger.
5. If necessary, reattach the cooling system
and reassemble the system according to the
documentation that came with your system.
12
3
4
MATXM-CORE-411-WR-Quick Start Guide
Artesyn Embedded Technologies
Marketing Communications
2900 S. Diablo Way, Suite 190
Tempe, Arizona 85282
Artesyn Embedded Technologies
Lilienthalstr. 17-19
85579 Neubiberg/Munich
Germany
Install the processor
cooler
1. Take the processor cooler and the back-
plate out of the antistatic package and
check for damages.
2. Take off the protective film from the
backplate to reveal the glue layer.
3. Align the backplate onto the mother-
board. The screw holes on the backplate
should fit exactly into the holes on the
motherboard.
Note: Make sure that the glue layer of the
backplate does not touch any other part
of the motherboard.
4. Place the cooler on the backplate
by screwing it on.
5. Connect the fan to the motherboard.
5Install the memory mod-
ule
1. Lay the MATXM-CORE-411-B where
the module is to be installed on the antistatic
desktop.
2. Take the SODDIM out of the antistatic pack-
age, holding it by the edges.
3. Line up the notch located on the row of the
metal pins at the bottom of the module with
the key in the SODIMM slot on
the motherboard.
4. Insert the SODIMM in a slantwise position or
at a 45-degree angle to slide the module into
place.
5. Press down on the module against the moth-
erboard until you hear it snap into place. The
modules must be properly aligned before you
press it down into its final position. You can
remove the module from the socket and rein-
stall it if you cannot easily press it down into
its final position.
6
Do not touch the memory chips when han-
dling the module.
Do not press on the memory chips when you
push it into its final position.
Do not touch the metal pins.
The MATXM-CORE-411-B (target) requires
two connections to the host computer – a
serial connection for the console output,
and an Ethernet connection for communi-
cation between the target and the Wind
River Workbench Development tools.
Perform the following procedure to con-
nect the target and host computer:
1. Ensure that your host computer is
switched off.
2. Connect the 9-pin serial cable between
the COM1 socket of the motherboard
MATXM-CORE- 411-B and the primary
serial port on your host machine.
3. Connect an Ethernet cable between the
Ethernet port on the motherboard
MATXM-CORE-411-B and the primary
Ethernet port on your host computer.
This can either be a direct connection or
through a hub or switch. Note that the
evaluation host and motherboard
MATXM-CORE-411-B will be assigned
pre-configured static IP addresses during
the evaluation.
7Connecting the Target and
Your Host Computer
MATXM-CORE-411-WR-Quick Start Guide
Artesyn Embedded Technologies
Marketing Communications
2900 S. Diablo Way, Suite 190
Tempe, Arizona 85282
Artesyn Embedded Technologies
Lilienthalstr. 17-19
85579 Neubiberg/Munich
Germany
Connecting the Target and
Your Host Computer (Cont.)
4. Ensure that the power supply for the mother-
board MATXM-CORE-411-B is correctly con-
nected.
7
Finding more information
For more information on the product, see
the MATXM-CORE-411-B Installation and Use
and other related documentation.
Visit our Web site http://www.artesyn.com/
computing. Use SUPPORT>TECHNICAL
DOCUMENTATION link to look for technical
documentation.
Technical Assistance
To request technical assistance, visit our
Web site http://www.artesyn.com
Table des matières
Autres manuels Artesyn Processeur
