Pro ceed PDP 3 Manuel utilisateur

1
Table of contents
Front panel ................................................................................................... 2
Rear panel ................................................................................................... 4
Unpacking ................................................................................................... 6
Set-up and installation ................................................................................ 7
Installing the spikes (optional) .................................................................. 7
Location...................................................................................................... 8
A word about cables ................................................................................ 8
A word about balanced output ............................................................. 9
Connecting digital sources to the PDP 3 ................................................ 9
Connecting the PDP 3's analog outputs ................................................ 9
Connecting the PDP 3's digital output (optional) ................................. 9
Power supply connection ...................................................................... 10
master power switch ............................................................................... 10
Care and maintenance ........................................................................... 11
Specifications ............................................................................................ 12
Pin assignments, male XLR balanced analog output ......................... 12
Pin assignments, female XLR digital input ............................................. 12
Troubleshooting ......................................................................................... 13
Service ....................................................................................................... 14

2
Front panel
emphasis 5
select
source 1 source 2 source 3 source 4
standby
6
4 3
1 2
sampling frequency
1 standby
When the master power switch on the rear panel is in the "|" (on)
position, pressing this button takes the PDP 3 out of “standby”
mode, turns the Display on, and makes the processor ready to
operate. (See “Rear panel”and “Set-up and installation.”)
2 Standby LED
This LED lights when the PDP 3 is in the standby mode.
3 sampling frequency Display
This Display shows the sampling frequency (expressed in kHz) for
the digital source you selected.
For digital FM, the Display will show 32; for compact disc digital
audio, the Display will show 44; for pre-recorded digital audio
tape, the Display will show 48. If no valid digital source is selected,
or if the selected source is inactive, the Display will show - - .
4 source LEDs
These LEDs light corresponding to the selected digital source.
5 select
Pressing this button selects the digital source, according to the
input connections on the rear panel. (See “Rear panel”and “Set-
up and installation.”)
Only one source at a time may be selected.
When the PDP 3 is taken out of the standby mode, the source last
selected before going into standby will be automatically selected
and the LED above that source will light; for example, source 1.
Pressing the select button at this point would select source 2;
pressing it again would select source 3, and so on. Pressing select
when source 4 is selected again selects source 1.

3
6 emphasis LED
This LED lights when the PDP 3 detects recording pre-emphasis in a
digital program, and subsequently employs its de-emphasis
circuitry.
NOTE: The de-emphasis circuitry of the Proceed PDP 3 is designed
to be compatible with all known digital standards. Under certain
conditions, however, the emphasis LED will light in error (that is,
when the digital program doesn’t contain recording pre-
emphasis).
This isn’t a malfunction of the PDP 3. Rather, it’s the result of
incorrect signals generated by the program source’s transport.
Depending on your transport and how you operate it, you may
never see this condition. Even when the condition exists, it has no
effect on sonic quality.

4
PRECAUTION
Rear panel
made in u.s.a.
PROCEED®PDP 3
master
power
digital
out
line out right line out left
source 1source 3
source 2
source 4
3 4 8 6 9
75101
PUSH
2
digital
inputs
1 master power
This switch turns the PDP 3 on and off. The switch must be in the "|"
(on) position for the processor to operate. (See "Set-up and
installation.")
NEVER operate the master power switch without first making sure
that power is turned off to your receiver, integrated amplifier, or
preamplifier/power amplifier.
2 Single-ended analog outputs
These outputs provide single-ended analog audio (via cables
equipped with RCA-type connectors) to a receiver, integrated
amplifier, or preamplifier equipped with unbalanced inputs. Most
components accept this type of output. (See "Set-up and
installation.")
3 Balanced analog outputs
These outputs provide balanced analog audio (via cables
equipped with XLR-type connectors) to a preamplifier, integrated
amplifier, or receiver equipped with balanced inputs. (See "Set-up
and installation.")
4 digital out
This output provides digital audio (via a cable equipped with
RCA-type connectors) to the digital input of a receiver,
integrated amplifier, preamplifier, or digital processor. (See "Set-
up and installation.")
5 source 1 digital input
This input accepts digital audio (via an optical cable equipped
with TOSLINK-type connectors) from the digital output of a digital
FM tuner, compact disc player, or digital audio tape recorder.

5
6 source 2 digital input
This input accepts digital audio (via an optical cable equipped
with ST-type connectors) from the digital output of a digital FM
tuner, compact disc player, or digital audio tape recorder.
7 source 3 digital input
This input accepts digital audio (via a cable equipped with RCA-
type connectors) from the digital output of a digital FM tuner,
compact disc player, or digital audio tape recorder.
8 source 4 digital input
This input accepts digital audio (via a cable equipped with XLR-
type connectors) from the digital output of a digital FM tuner,
compact disc player, or digital audio tape recorder.
9 AC power cord
This cord supplies AC power to the PDP 3. (See "Set-up and
installation.")
10 Fuse
This holder contains the main fuse for the PDP 3. If the fuse ever
needs to be replaced, contact your Proceed dealer.

6
Unpacking
Carefully open the shipping carton and remove the contents. You
should have:
■Proceed PDP 3
■Owner’s manual
■Four spikes
■Hex key
Save the shipping carton and all packing material. Though it may be
inconvenient to store, it’ll come in handy for shipping if you move, or if
the unit needs to be shipped for service.
Locate the serial number (on the back panel), and record it here:
■Serial Number:
Keep your sales receipt where you can find it. You’ll need to show it
for any service during the warranty period. Take a moment now to
record some information from the receipt:
■Date of purchase:
■Proceed dealer:
■Dealer’s address:
■Dealer’s telephone number:

7
Set-up and installation
To set up your Proceed PDP 3, you’ll need:
■A soft cloth or towel (step 2)
■A high-quality audio cable for each digital source you intend to
connect to the PDP 3 (step 6)
■A pair of high-quality audio cables for connecting the PDP 3 to
your receiver, integrated amplifier, or preamplifier (step 7)
■A high-quality audio cable for connecting the PDP 3's digital
output to another digital processor (optional; step 8)
1. Make sure that the PDP 3 is unplugged from the AC power supply
and disconnected from your receiver, integrated amplifier, or
preamplifier.
2. Place the PDP 3 upright on a flat, stable surface. Carefully tip it so it
rests on its top; protect its finish with a soft cloth.
3. The PDP 3 is shipped so that it rests solidly on two wide “feet,”
positioned under the front and back of the unit.
You may want to explore the potential sonic advantages of
installing the specially designed “spikes”supplied with the unit.
One arrangement is to install the spikes under the corners of the
unit:
Four spikes,
mounted at the corners
Installing the spikes
(optional)

8
You may choose instead to install the spikes in a triangular
arrangement:
Install the spikes one at a time.
Using the supplied hex key, remove
the screw securing the foot to the base of the unit. Insert the
threaded end of the spike through the hole in the foot, then turn it
clockwise until it’s hand-tight. (Be careful not to over-tighten it.)
Repeat this procedure for each spike you install.
4. Turn the PDP 3 upright, and place it in the desired location.
The PDP 3 should be located on a level, stable surface. Avoid
placing it where it will be exposed to shocks or vibration (such as
on an unstable table or near large loudspeakers). For best
performance, locate the PDP 3 away from tuners, televisions, and
other sources of radio frequencies.
DON'T place the PDP 3 on top of another component, since its
base could block the other component’s ventilation. Interfering
with the PDP 3’s ventilation or that of another component could
cause either to overheat, resulting in damage to your system.
5.
Make sure that power is turned off to both the PDP 3 and your
receiver, integrated amplifier, or preamplifier/power amplifier.
■The quality of the cables and connectors that you use with your
Proceed PDP 3 can noticeably affect the quality of the sound
that you hear from your speakers or headphones. For the best
performance, use the highest quality audio cables available.
Though there are many such cables to choose from, we
confidently recommend Madrigal HPC cables (for analog
signals) and Madrigal MDC (for electrical digital signals). See
your Proceed dealer for more information.
Three spikes,
mounted in a
triangular pattern
PRECAUTION
A word about cables
Location

9
■The Proceed PDP 3 provides balanced analog output by way of
standard three-pin XLR-type connectors. This provides the
highest quality connection and, therefore, the best sound.
Terminated with the proper connector, balanced input on an
amplifier or power amplifier minimizes the chance of
“coloration”of the sound due to cabling. If you’re unfamiliar
with balanced interconnection and how it works with your
audio system, see your Proceed dealer for more information.
For instructions on connecting digital sources to the Proceed PDP 3,
see step 6.
For instructions on connecting the Proceed PDP 3’s balanced or
unbalanced analog outputs to your audio system, see step 7.
For instructions on connecting the Proceed PDP 3’s digital outputs
to your audio system, see step 8.
6. Using a high-quality audio cable, connect the digital output of a
digital audio component (such as a digital FM tuner, compact disc
player, or digital audio tape recorder) to one of the inputs on the
rear panel of the PDP 3.
You may connect up to four digital sources to the PDP 3.
■source 1 accepts digital audio via a cable equipped with
TOSLINK-type optical connectors.
■source 2 accepts digital audio via a cable equipped with ST-
type optical connectors.
■source 3 accepts digital audio via a cable equipped with RCA-
type connectors.
■source 4 input accepts AES/EBU digital audio via a cable
equipped with XLR-type connectors.
7. Using a pair of high-quality audio cables, connect the PDP 3's line
out left and line out right to left and right
line-level
inputs of your
receiver, integrated amplifier, or preamplifier. Make sure to
connect the left output of the PDP 3 to the left input of the
receiver, integrated amplifier, or preamplifier, and likewise for the
right channel.
NEVER connect the PDP 3’sbalanced or unbalanced outputs to
PHONO inputs.
8. Using a high-quality audio cable, connect the digital output of the
PDP 3 to the digital input of your receiver, integrated amplifier,
preamplifier, or digital processor.
NEVER connect the PDP 3’s digital output to PHONO inputs.
A word about
balanced output
Connecting digital sources
to the PDP 3
Connecting the PDP 3's
analog outputs
Connecting the PDP 3's
digital output (optional)

10
9. Connect the power supply cord of the PDP 3 to an unswitched
convenience outlet (like those on the rear panel of many audio
components). If you connect the PDP 3 directly to a wall outlet,
make sure that the outlet has polarized sockets.
10. Set the master power switch on the rear panel to the “|”(on)
position, and allow the PDP 3’s circuitry to stabilize for several
minutes before operating it.
Note: The PDP 3 won't achieve its sonic potential right away —
sonic performance is close to the optimum after 350 hours (or
about two weeks of normal use). For the best performance, you
may leave it powered at all times, except when you won't be using
it for a long period (see "Important Safety Instructions").
The PDP 3 may be turned on and off without affecting its longevity.
When it is turned on after being left unpowered, allow about one
hour before expecting optimal sonic performance.
NEVER operate the master power switch without first making sure
that power is turned off to your receiver, integrated amplifier, or
preamplifier/power amplifier.
11. After making all connections and turning the master power switch
on, turn on the other components in your system.
Power supply connection
master power switch
PRECAUTION
Table des matières
Manuels Processeur populaires d'autres marques

GrandTec
GrandTec Grand Magic Guard III Manuel utilisateur

Intel
Intel 80386 Guide rapide de l'utilisateur

TECshow
TECshow DSP-2600 W Manuel utilisateur

Topp Music Gear
Topp Music Gear RT-DRIVE DLM-206 Manuel utilisateur

NEC
NEC IPS-4000 Manuel utilisateur

Texas Instruments
Texas Instruments Sitara AM335x Manuel utilisateur











