Arteflame Classic 40 Manuel utilisateur
ASSEMBLY INSTRUCTIONS
CLASSIC 40” GRILL - LOW BASE
All manuals and user guides at all-guides.com
2
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
Thank you for your purchase!
You are minutes away from firing up your Arteflame and
beginning to experience outdoor entertainment, Arteflame style.
Assembly is simple and requires two people.
When you first unpack your grill, carefully unpack all the
components and move them to where you want to assemble
your grill. Handle all parts by the edges as to not disturb the
natural patina already present. If you are setting up the Classic
grill in grass or in sand, you may choose to just assemble the base
without the stainless steel base plate.
Attention
Assembly requires two people and we recommend holding all
parts by their edges while wearing gloves
2 persons Wear gloves
All manuals and user guides at all-guides.com
3
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
Classic Base assembly
The Classic Base is made up of three pieces pictured below from
left to right:
■One Corten steel round base
approximately 20 pounds (9 kg)
■Four feet for leveling the round base
■Coal catcher
All Corten steel parts have a carefully developed patina and
should be handled with care as to not scratch, damage or disturb
the patina on them.
x4
All manuals and user guides at all-guides.com
4
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
Place the Corten Round Base
where you will be using your
Arteflame, with the leveling feet
on the bottom. Adjust the four
leveling feet to make the base
level and stable.
NOTE: The outside of the base
has a decorative patina from the
factory. This patina can easily be
disturbed when handling the
base. If it does get disturbed, no
worries, it will come back given a
little time.
Step 1
All manuals and user guides at all-guides.com
5
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
The Arteflame draws in air
through the bottom of the base
so make sure you have a 3/8” to
1/2” air gap under the base.
NOTE: Each cone Arteflame
base is manually formed and will
not be perfectly round. This is
normal and expected.
Slide the coal catcher
underneath the grill between
the leveling feet.
NOTE: The coal catcher is
designed to catch any potential
ashes that may fall through the
grill and land on the ground.
Periodically check the coal
catcher by sliding it out from
under the base and clean it o
as necessary.
Step
Step
2
3
All manuals and user guides at all-guides.com
6
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
All manuals and user guides at all-guides.com
7
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
Cooktop assembly
The Arteflame Classic 40 Bowl is made up of three pieces:
■The laser cut carbon steel cooktop
approximately 150 pounds (68 kg)
■The Corten steel firebase
■The spun Arteflame Corten steel bowl
approximately 67 pounds (30 kg)
Moving the cooktop into place requires two people and a 6’ to
8’ piece of 2x4 lumber. This is a two person job using the 2x4
cooktop lifter provided.
All manuals and user guides at all-guides.com
8
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
With two people, lift the
Arteflame fire bowl by the
inside ring so the patina doesn’t
get disturbed.
Carefully walk the fire bowl to
the grilling location where the
base is waiting. Carefully place
it on top of the base as level as
possible.
Step 1
The firebase is shipped inside
the bowl. If it is removed during
installation, it needs to be put
into the bowl before putting
the cooktop on top of the
bowl. Pickup the firebase and
carefully rest it inside the bowl
on the 3 metal brackets inside
the bowl.
Step 2
All manuals and user guides at all-guides.com
9
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
With two people, carefully place
the cooktop on the bowl using
the lifting tool.
The cooktop slightly overhangs
the bowl evenly on all sides.
Always use the included lifting
tool. If the lifter can’t be used,
position the bowl by lifting it
through the center hole ONLY.
DO NOT lift it by the outer
edge as your fingers could get
pinched between the bowl and
the cooktop.
Step 4
Insert the cooktop lifter into
the center hole of the cooktop
and slide a 6-8 foot long piece
of 2x4 lumber through the top
as shown. With two people, lift
the cooktop and set it down
near where you are going to be
setting up your grill. NEVER
install the cooktop by hand
holding it on the outside rim as
fingers can get pinched.
Step 3
All manuals and user guides at all-guides.com
10
CLASSIC 40” GRILL - LOW BASE
ASSEMBLY INSTRUCTIONS
Your fully assembled Arteflame grill is now complete! Make sure
your Arteflame is as level as possible so all excess grease will
always flow into the middle and into the fire.
You are now ready to build your fire and start the seasoning
process of the cooktop. Any cooking oil can be used but we
recommend using flaxseed oil for best results.
You can use a carpenter level or even your smartphone if it has a
level function. When leveling the cooktop, please note that the
cooktop is sloped downward towards the middle to allow oils to
slide into the grill center. To get your best readings on levelness,
place the leveling device around the outer edge of the cooktop to
give you the most accurate reading.
All manuals and user guides at all-guides.com
Autres manuels pour Classic 40
1
Table des matières
Autres manuels Arteflame Gril
Arteflame
Arteflame EURO 20 GRILL Manuel utilisateur
Arteflame
Arteflame EURO 30 Manuel utilisateur
Arteflame
Arteflame Classic 40 Euro Tall Base Manuel utilisateur
Arteflame
Arteflame Classic Cooktop Manuel utilisateur
Arteflame
Arteflame One Series Manuel utilisateur
Arteflame
Arteflame Classic Euro 40 Low Base Manuel utilisateur
Arteflame
Arteflame Euro Base Manuel utilisateur
Arteflame
Arteflame One Series Manuel utilisateur
Arteflame
Arteflame CLASSIC 40 GRILL TALL BASE Manuel utilisateur
Arteflame
Arteflame EURO 20 Manuel utilisateur
