ARIES INDUSTRIES CT1750 Manuel utilisateur
970262_A
ELECTRIC WOLVERINE (CT1750)
Wheeled Electric Cutter
Operation and Maintenance
ries
Corporate Office:
550 Elizabeth Street
,
Waukesha, WI 53186
800-234-7205 262-896-7205 Fax: 262-896-7099
Western Regional Office: 5748 East Shields Avenue, Suite 101, Fresno, CA 93727
800-671-0383 559-291-0383 Fax: 559-291-0463
Southeast Regional Office: 561 Thornton Road, Suite D, Lithia Springs, GA 30122
800-327-4346 770-941-1144 Fax: 770-941-1141
Canadian Regional Office: 95 Whitmore Road, Unit 1, Vaughan, Ontario L4L 6E2
877-730-7010 905-265-2279 Fax: 905-265-2299
ries Web Site: www.ariesindustries.com
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 1
This document contains proprietary and
confidential information of Aries Industries, Inc.
Copyright 2017 Aries Industries, Inc.
All rights reserved.
Disclaimer
The information contained in this document has been carefully checked and is believed to be
entirely reliable and consistent with the products described. However, no responsibility is
assumed for inaccuracies, nor does Aries Industries, Inc. assume any liability arising out of the
application and use of the equipment described. Aries Industries, Inc. reserves the right to
make changes to any product and product documentation in an effort to improve performance,
reliability, or design.
Warranty
Aries products are thoroughly inspected before shipment. In the event of any malfunction,
contact the nearest Aries office.
Aries will replace or repair defective manufactured parts, F.O.B. factory, for one year from the
date of shipment. See Aries full warranty statement for complete details.
Notice
No part of this document should be reprinted or reproduced without the prior written
permission of Aries Industries, Inc.
If you have any problems or questions regarding this document, please contact one of the Aries
offices listed on the front cover.
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 2
T BLE OF CONTENTS
Section One – Operation and Maintenance
Subject Page
Introduction 7
Safety
Electric Wolverine Equipment Safety 8
Pipeline and Manhole Safety 8
Truck System Interface
Cable Connections 9
Wolverine Air Reel Cable 10
Equipment Selection Switch 11
Components
Standard 11
Options 12
Width/Height Conversion
Arrangements for Various Pipe Diameters 13
Operation
Drive Forward Drive Backward 14
Cutting Motor Rotate Left Rotate Right 14
Cutting Motor Lift Up Lift Down 14
4
th
Axis Working Head In Working Head Out 15
Pipe Clamp Inflate Deflate 15
Water Control 15
Camera Rotate Up Rotate Down 15
Camera Brightness 16
Cutting Motor On Off 16
Tractor Retrieval 16
Maintenance
Cleaning Inspection 17
Returning Equipment 18
Ordering Equipment 18
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 3
Section Two – Drawings and Parts Lists
Subject Page
CT1750 Cutter Tractor Assembly 21
380405 Cutter Tractor Assembly w o Wheels, Arms, or Grind Motor 22
380629 Main Body Assembly 23
380629 Main Body Assembly, Bill of Materials 24
380628 Tip-Up Assembly 25
380628 Tip-Up Assembly, Bill of Materials 26
380635 Rotate Head Assembly 27
380499 Rotate Head Inner Assembly 28
380660 Rotate Head Center Assembly 29
380660 Rotate Head Center Assembly, Bill of Materials 30
380480 Up-Down Gear Box Assembly 31
380656 Arms and Hardware Kit 32
380360 Front Motor Assembly 33
380350 Rear Motor Assembly 34
380570 Water Jet Assembly 35
380123 Large Line Wheel Extension #1 36
380524 Large Line Wheel Extension #2 37
380204 Carbide and Rubber Wheel Set 38
380197 Carbide Tire Assembly, 3 Inch 39
380184 Carbide Tire Assembly, 4 Inch 40
380195 Carbide Tire Assembly, 5 Inch 41
380347 Carbide Tire Assembly, Pipe ID 12 – 18 Inch 42
380203 Rubber Tire Assembly, 3-3 8 x 45D 43
380191 Rubber Tire Assembly, 4-3 8 x 5 8 65D 44
380196 Rubber Tire Assembly, 5 x 1-1 4 60D 45
380103 Top Clamp Roller Guide, Small 46
380102 Top Clamp Roller Guide, Large 47
380657 Top Clamp, DN130 6 Inch Relined Pipe Kit 48
380658 Top Clamp, DN150 6 Inch Pipe Kit 49
380659 Top Clamp, DN200 8 Inch Pipe Kit 50
380661 Top Clamp, DN250 10 Inch Pipe Kit 51
380662 Top Clamp, DN300 12 Inch Pipe Kit 52
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 4
Section Two – Drawings and Parts Lists (cont’d)
Subject Page
380655 Top Clamp, DN400 15 Inch Pipe Kit 53
380290 Electric Motor, Sheet 1 of 2 54
380290 Electric Motor, Sheet 2 of 2 55
380687 Electric Motor Extension Kit 56
380172 Collet Assembly, M10 57
380115 4
th
Axis Kit, 4 Pole 58
380115 4
th
Axis Kit, 4 Pole, Bill of Materials 59
381049 4
th
Axis Kit, 2 Pole 60
381049 4
th
Axis Kit, 2 Pole, Bill of Materials 61
380944 4
th
Axis Kit, 4 Pole to 2 Pole Conversion 62
380001 LED Camera Kit, Bill of Materials 63
380353 LED Camera, Sheet 1 of 4 64
380353 LED Camera, Sheet 2 of 4 65
380353 LED Camera, Sheet 3 of 4 66
380353 LED Camera, Sheet 4 of 4 67
380373 LED Camera Glass W Seals Kit, Bill of Materials 68
381050 Inner Connect Hose Kit 69
380090 Inner Connect Tow Clevis 70
380372 Slip Ring Assembly 71
380958 Common Hardware Kit, Bill of Materials 72
380685 Oversized Arms & Clutches Kit, Bill of Materials 73
950637 Spare Parts Kit, Bill of Materials 74
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 5
This page was intentionally left blank
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 6
Section One
Operation and Maintenance
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 7
Electric Wolverine
Section One
Operation and Maintenance
Introduction
The Aries Electric Wolverine is a wheeled, self-propelled cutter tractor made for reinstalling
junctions or cutting out infiltrations found in the pipe. The Wolverine cutter tractor operates in
pipes sizes between 6 and 18 inches in diameter. The cutter tractor operates best in a prepared
pipeline. The Wolverine is driven by two axles, using 48V motors. The cutter tractor operates
using the Aries truck-mounted, mainline systems CC1750 control system and PR1750 Electric
Wolverine reel. Optimum cutter tractor operation requires proper electrical connections to the
Electric Wolverine cutter reel and tractor, the correct air pressure, and proper wheel and
extensions arrangements for the pipeline diameter being worked in. The Electric Wolverine
cutter tractor may sometimes be referred to as the CT1750. This manual is designed to assist
personnel when performing tractor configurations, wheel conversions, and maintenance
procedures.
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 8
Electric Wolverine
Section One
Operation and Maintenance
Safety
Care and precautions are needed when operating any electrical components in wet and
confined spaces.
Electric Wolverine Equipment Safety
1. Read and understand the supplied instructions before operating equipment.
2. The CT1750 Electric Wolverine cutter tractor is equipped with powerful cutting motor
arms that can pinch, causing injury to fingers or extremities.
3. To prevent personal injury or damage to equipment, turn off and disconnect all power
when making adjustments or performing maintenance.
4. Inspect cables before and after each use. Replace or repair any damaged cables.
5. Before connecting or disconnecting cables, verify all system power is off.
6. Lift cutter tractor solely with lift strap. Use main reel cable to guide tractor in and out of
the manholes. Do not lift cutter tractor by power cords, hoses, lift arms, or top clamp.
7. Do not use in hazardous or explosive atmospheres.
8. Do not submerge the cutter for prolonged periods. It is water resistant, NOT waterproof.
9. Do not drop the cutter tractor assembly.
Pipeline and Manhole Safety
1. Use the appropriate safety equipment and clothing - goggles, gloves, boots,
masks respirators, traffic signs, and cones - when working in confined spaces.
2. Follow all appropriate laws, regulations and guidelines for working in confined spaces.
3. Pipeline conditions are an important factor in life expectancy of your equipment.
Protruding taps, corroded or clogged lines, large offsets, and short sags in pipe make
travel difficult. Proceed carefully in those conditions.
Always use a lifting hook when lowering or raising the Electric Wolverine cutter tractor with a
retrieval pole assembly.
NOTES: Item 2 is not used on Electric Wolverine cutter tractors.
970262_A Aries Industries, Inc. ▪ (800) 234-7205 ▪ www.ariesindustries.com Page 9
Electric Wolverine
Section One
Operation and Maintenance
Truck System Interface
For first time users, use the Wolverine Quick Start Guide Manual (P N 970245) for operation
setup. The quick start guide was created to help direct users on how to set up the Wolverine
system correctly via step by step instructions and pictures.
Cable Connections
The Electric Wolverine cutter tractor requires three electrical cables and three hose
connections for full functionality. These inner connect points are located between the reel
cable termination and the Wolverine cutter tractor tip-up assembly. The three inner connect
cables are a two pin cable (P N 380112), a nineteen pin cable (P N 380113), and an eight coil
cable (P N 380380). The inner connect hoses are a small, blue air hose (P N 381053), a small,
black water hose (P N 381052), and a small, blue hose (P N 381015). These inner connect
points must be securely fastened and undamaged for full functionality. The strain relief from
the reel termination needs to be connected to the clevises (P N 380090) on the cutter tractor
tip-up to protect these inner connect points from damage before using the Electric Wolverine
cutter tractor.
If operations from the drive motors, the cutter tractor functions, or the cutter tractor camera
do not respond or respond faintly, troubleshoot the problem by using the inner connect cables
with the faceplate on the CC1750. The CC1750 control unit has a large nineteen pin socket and
a small two pin socket located on its faceplate. The nineteen pin socket is to test the cutter
tractor and cutter tractor camera (P N 380353). The two pin socket is to test the drive motors
(Front P N 380360 Rear P N 380350).
If the problems go away in testing the inner connect cables with the cutter tractor and camera
on the CC1750 control unit’s faceplate, the reel can be identified as the problem. See
Wolverine Electric Reel Cable for more information. If problems persist with the cutter tractor
or camera when using the inner connect cables with the faceplate, then the Electric Wolverine
reel and cable can be eliminated as the source of the issue.
Next, use the test cables to connect the cutter tractor and camera to the CC1750 faceplate. If
the problems do not go away when using the test cables with the cutter tractor or camera, then
the tractor and camera have been identified as the problem. Return the equipment to an Aries
facility for repair. See the Returning Equipment section. If the problems do go away when
using the test cables with the cutter tractor and camera, then the cable must be replaced. See
the Ordering Equipment section.
Table des matières
