Ariens Deluxe 30 Manuel utilisateur

Quick Start Guide

Deluxe 30 (921013 s/n 75000 & up)

•Step 1: Assemble Handlebars

•Step 2: Connect Headlight Wire Harness

•Step 3: Install Trigger Cable

•Step 4: Install Discharge Chute

•Step 5: Install Discharge Chute Crank

•Step 6: Install Remote Deflector Control Cable

•Step 7: Install Skid Shoes

•Step 8: Check Function of Dual Handle Interlock

•Step 9: Check Tire Pressure

•Step 10: Check Auger Gearcase Oil

•Step 11: Check Engine Crankcase Oil

•Step 12: Fill Engine Fuel Tank

•Step 13: Start Engine

•Step 14: Stop Engine

READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.

IMPORTANT: READ OPERATOR’S MANUAL AND ENGINE MANUAL

THOROUGHLY AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES

BEFORE OPERATING.

Step One: Assemble Handlebars

(Unfold Lower Handlebar)

IMPORTANT: Be sure to block wheels or secure unit so it does not

move during assembly.

1. Rotate lower handlebar out from unit so lower handlebar

mounting holes align with mounting holes on the unit frame.

2. Secure lower handlebar to unit using two 3/8 in. x 3/4 in. hex

head serrated flange grade 5 bolts.

3. Tighten all four bolts to 25-42 lbf-ft (33,9-56,9 N∙m)

Step One: Assemble Handlebars

(Attach Upper Handlebar Assembly)

1. Attach upper handlebar assembly to lower handlebar using

two sets of the handlebar hardware. One set to attach each

side of the handlebars.

NOTE: DO NOT tighten hardware. Allow upper handlebar

assembly to hang from the lower handlebars for the next step.

Step One: Assemble Handlebars

(Attach Control Cables)

1. Hook Spring end of attachment control cable to the clutch

arm.

2. Hook spring end of the traction control cable to the cable

eyelet on back of frame.

NOTE: Make sure cable remains in groove of pulley.

Step One: Assemble Handlebars

(Unfold Upper Handlebar)

Assembly)

1. Rotate handlebar into operating position.

NOTE: Be careful not to damage cable spring hooks when rotating

handlebar upward.

2. Install the remaining handlebar hardware attaching the upper

handlebar assembly to the lower handlebar.

3. Tighten all hardware.

4. Remove packaging around shift rod.

5. Rotate shift rod into place and tighten hardware.

6. Connect shift rod to speed selector arm and adjust as

specified. See Selector Adjustment in the Owners Manual.

7. Adjust attachment cable as specified. See Attachment

Clutch/Brake Adjustment in the Owners Manual.

8. Adjust the traction cable as specified. See Traction Drive

Clutch Adjustment in the Owners Manual.

Step Two:

Connect Headlight Wire Harness

NOTE: The headlight wire harness comes attached to the upper

handlebar assembly.

1. Route the wire harness along the interior of the right side

handlebar.

2. Connect to the engine electrical plug.

3. Press cable anchor into mounting hole in the frame near the

engine electrical plug.

4. Secure the wire harness to the handlebars using the cable

ties attached to the wire harness.

Step Three:

Install Trigger Cable

NOTE: Trigger cable assembly comes attached to the Sno-thro

unit.

1. Attach remote trigger cable assembly to upper handlebar

assembly using one ¼ in x 1- ½ oval head machine screw and

one ¼ in. locking washer.

Step Four:

Install Discharge Chute

1. Grease underside of discharge chute ring (if not already

greased).

2. Remove mounting hardware from auger housing.

3. Install discharge chute over opening in the auger housing.

Finger tighten the mounting hardware removed above.

NOTE: Leave discharge chute pedestal loose to help install the

chute crank.

Step Five: Install

Discharge Chute Crank

1. Remove the gear cover from top of chute pedestal.

2. Insert the short end of the chute crank into the hole in the front

of the control panel.

NOTE: Be careful not to damage nylon bushing when attaching

crank to the dash.

3. Connect the chute crank to the pinion gear on chute with

hairpin.

4. Replace gear cover on top of chute pedestal.

5. Orient the chute and pedestal to its most vertical position and

tighten pedestal hardware to 15 – 31 lbf-ft (20 – 42 N•m).

Step Six: Install Remote

Deflector Control Cable

NOTE: Connect the barrel cable end to the chute deflector cable anchor

before clipping the cable to the discharge chute cable bracket.

1. Route deflector remote cable along the left side of the chute

pedestal.

2. Insert the barrel on the cable end into the bracket on left side of

chute deflector.

3. Hold seal out of the way while routing the cable through the bracket

on the left side of the discharge chute, and then push the cable

fitting into the bracket.

4. Push the seal securely over the end on the cable fitting to prevent

water from entering the cable.

5. Check deflector travel. Adjust nut on cable end under handlebar to

obtain full travel, if necessary (see Remote Deflector Control in

Owners Manual.

Autres manuels pour Deluxe 30

Table des matières

Autres manuels Ariens Souffleuse à neige

Ariens

Ariens Professional Sno-Thro Series Manuel utilisateur

Ariens

Ariens 10995 Manuel d'utilisation et d'entretien

Ariens

Ariens Sno-Thro ST520E Manuel du propriétaire

Ariens

Ariens 932035-724 Manuel du propriétaire

Ariens

Ariens 924 Manuel du propriétaire

Ariens

Ariens SNO- THROS 832002 Manuel utilisateur

Ariens

Ariens Sno-Thro 920001 Manuel du propriétaire

Ariens

Ariens Sno-Tek 28E Manuel utilisateur

Ariens

Ariens Sno-Thro 939003-ST520E Manuel du propriétaire

Ariens

Ariens Sno-Thro Deluxe Track 24 Manuel utilisateur

Ariens

Ariens Sno-Thro Classic 24 Manuel utilisateur

Ariens

Ariens Sno-Thro 924 Series Manuel utilisateur

Ariens

Ariens 100 - ST824 Manuel utilisateur

Ariens

Ariens SNO-THRO 924124 ST926DLE Manuel du propriétaire

Ariens

Ariens SNO-THRO 932037 - 724 Manuel du propriétaire

Ariens

Ariens 920014 Manuel du propriétaire

Ariens

Ariens Sno-Thro 932001 Manuel utilisateur

Ariens

Ariens SNO-THRO 932102 - 520 Manuel du propriétaire

Ariens

Ariens 921045 Manuel utilisateur

Ariens

Ariens 921053 Manuel utilisateur

Ariens

Ariens Sno-Thro Pro 28 926038 Manuel utilisateur

Ariens

Ariens 920021-Compact 24 LE Manuel utilisateur

Ariens

Ariens Sno-Thro Pro 28 926038 Manuel du propriétaire

Ariens

Ariens Sno-Thro Pro 28 Manuel utilisateur

Manuels Souffleuse à neige populaires d'autres marques

Murray

Murray 624504X4A Manuel utilisateur

Blizzard

Blizzard POWER PLOW 8100PP Manuel utilisateur

Craftsman

Craftsman 486.24837 Manuel utilisateur

Yard-Man

Yard-Man E2B5 Manuel utilisateur

ST ST 526 A Manuel utilisateur

MTD

MTD 3AA Manuel utilisateur

Toro

Toro Power TRX 1428 OHXE Manuel utilisateur

Ryobi

Ryobi RYAC800 Manuel utilisateur

Poulan Pro

Poulan Pro 416829 Manuel utilisateur

Poulan Pro

Poulan Pro 437986 Manuel utilisateur

MTD

MTD 319-180-00 Manuel utilisateur

Brute

Brute 1695565 Manuel utilisateur

Egholm

Egholm City Ranger 2250 Manuel utilisateur

Poulan Pro

Poulan Pro 420915 Manuel utilisateur

GreenWorks

GreenWorks SNF402 Manuel utilisateur

LOFTNESS

LOFTNESS 601D1 Manuel utilisateur

LOFTNESS

LOFTNESS 1082I Manuel utilisateur

LOFTNESS

LOFTNESS 481EL Manuel utilisateur