Ariens A149K21 (96136300) Manuel utilisateur

A149K21

(96136300)

Owner's Manual

431614 Rev 3 03.31.10 BY •EspaSol, p 18

Printed in USA

Safety Rules .......................................... 2-4

Product Specifications .............................. 4

Assembly /Pre-Operation ........................ 5

Operation ............................................... 6-9

Maintenance Schedule ........................... 10

Maintenance ...................................... 10-12

Service and Adjustments ........................ 13

Storage .............................................. 14-15

Troubleshooting ................................. 15-16

Repair Parts....................................... 32-33

Warranty ................................................. 36

IMPORTANT: This cutting machine is

capable of amputating hands and feet and

throwing objects. Failure to observe the

following safety instructions could result in

serious injury or death.

_,Look for this symbol to point out impor-

tant safety precautions. It means

CAUTION!!! BECOME ALERT!!t

YOUR SAFETY ]S INVOLVED.

_, WARNING; In order to prevent ac-

cidental starting when setting up, trans-

porting, adjusting or making repairs,

always disconnect spark plug wire and

place wire where it cannot come in contact

with plug.

_WARNING: Engine exhaust, some of its

constituents, and certain vehicle components

contain or emit chemicals known tothe State

ofCalifornia tocause cancer and birthdefects

or other reproductive harm.

-o-WARNING: Battery posts, terminals and

related accessories contain lead and lead

compounds, chemicals known to the State

of California to cause cancer and birth

defects or other reproductive harm. Wash

hands after handling.

A CAUTION: Muffler and other engine

parts become extremely hot during

operation and remain hot after engine

has stopped. To avoid severe burns on

contact, stay away from these areas.

I, GENERAL OPERATION

• Read, understand, and follow all

instructions on the machine and in the

manual(s) before starting. Bethoroughly

familiar with the controls and the proper

use of the machine before starting.

• Do not put hands or feet near or under

rotating parts. Keep clear of the dis-

charge opening at all times.

• Only allow responsible individuals, who

are familiar with the instructions, to oper-

ate the machine.

•Clear the area of objects such as rocks,

toys, wire, bones, sticks, etc., which

could be picked up and thrown by blade.

• Be sure the area is clear of other people

before mowing. Stop machine if anyone

enters the area.

• Do not operate the mower when bare-

foot or wearing open sandals. Always

wear substantial foot wear.

• Do not pull mower backwards unless

absolutely necessary. Always look down

and behind before and while moving

backwards.

• Never direct discharged material toward

anyone. Avoid discharging material

against a wall or obstruction. Material

may richochet back toward the opera-

tor. Stop the blade when crossing gravel

surfaces.

• Do not operate the mower without

proper guards, plates, grass catcher or

other safety protective devices in place.

• See manufacturer's instructions for

proper operation and installation of

accessories. Only use accessories ap-

proved by the manufacturer.

• Stop the blade(s) when crossing gravel

drives, walks, or roads.

° Stop the engine (motor) whenever you

leave the equipment, before cleaning the

mower or unclogging the chute.

• Shut the engine (motor) off and wait until

the blade comes to complete stop before

removing grass catcher.

• Mow only in daylight or good artificial

2 light.

• Donotoperatethemachinewhileunder

theinfluenceofalcoholordrugs.

•Never operate machine in wet grass.

Always be sure of your footing: keep a

firm hold on the handle; walk, never run.

° Disengage the self-propelled mech-

anism or drive clutch on mowers so

equipped before starting the engine.

• Ifthe equipment should start to vibrate

abnormally, stop the engine (motor) and

check immediately for the cause. Vibra-

tion is generally a warning of trouble.

• Always wear safety goggles or safety

glasses with side shields when operating

mower.

II, SLOPE OPERATION

Slopes are a major factor related to slip&

fall accidents whichcan result in severe

injury.All slopes requireextra caution,if

you feel uneasyon a slope, do notmow it.

DO:

° Mow acrossthe face ofslopes: never

upand down. Exercise extreme caution

when changingdirection on slopes.

° Remove obstacles such as rocks,tree

limbs,etc.

• Watch for holes, ruts, or bumps.Tall

grass can hideobstacles.

DO NOT:

oDo nottrimnear drop-offs, ditches or

embankments. The operatorcouldlose

footing or balance.

° Do not trimexcessively steep slopes.

° Do not mow on wet grass. Reduced

footing could cause slipping.

III, CHILDREN

Tragic accidents can occur if the operator

is not alert to the presence of children.

Children are often attracted to the machine

and the mowing activity. Never assume

that children will remain where you last

saw them.

• Keep children out of the trimming area

and under the watchful care of another

responsible adult.

• Be alert and turn machine off if children

enter the area.

,Before and while walking backwards,

look behind and down for small children.

• Never allow children to operate the

machine.

• Use extra care when approaching blind

comers, shrubs, trees, or other objects

that may obscure vision.

IV. SAFE HANDLING OF GASOLINE

Use extreme care in handling gasoline.

Gasoline is extremely flammable and the

vapors are explosive.

• Extinguish all cigarettes,cigars, pipes

and other sources of ignition.

• Use only an approved container.

° Never remove gas cap or add fuel with

the engine running. Allow engine to cool

before refueling.

• Never refuel the machine indoors.

°Never store the machine or fuel contain-

er where there is an open flame, spark

or pilot lightsuch as a water heater or

on other appliances.

• Never fill containers insidea vehicle, on

a truck or trailer bed with a plastic liner.

Always place containers on the ground

away from your vehicle before filling.

•Remove gas-powered equipment from

the truck or trailer and refuel it on the

ground. Ifthis is not possible, then

refuel such equipment with a portable

container, rather than from a gasoline

dispenser nozzte.

•Keep the nozzle in contact with the rim

of the fuel tank or container opening at

all times until fueling iscomplete. Do

not use a nozzle lock-open device.

° Iffuel is spilled on clothing, change

clothing immediately.

•Never overfill fuel tank. Replace gas

cap and tighten securely.

V. GENERAL SERVICE

° Never run a machine inside a closed

area.

• Never make adjustments or repairs with

the engine (motor) running. Disconnect

the spark plug wire, and keep the wire

away from the plug to prevent accidental

starting.

• Keep nuts and bolts, especially blade

attachment bolts, tight and keep equip-

ment in good condition.

•Never tamper with safety devices.

Check their proper operation regularly.

•Keep machine free of grass, leaves, or

otherdebris build-up. Clean oil or fuel

spillage. Allow machine to cool before

storing.

° Stop and inspect the equipment if you

strike an object. Repair, if necessary,

before restarting.

•Never attempt to make wheel height

adjustments whUethe engine is running.

° Grass catcher components are subject

to wear, damage, and deterioration,

which could expose moving parts or

allow objects to be thrown. Frequently

check components and replace with

manufacturer's recommended parts,

when necessary.

• Mower blades are sharp and can cut.

Wrap the blade(s) or wear gloves, and

use extra caution when servicing them.

• Do not change the engine governor set-

ting or overspeed the engine.

• Maintain or replace safety and instruc+

tion labels, as necessary.

_kWARNING.* This lawn mower is equipped with an internal combustion engine and

should not be used on or near any unimproved forest-covered, brush-covered or

grass-covered land unless the engine's exhaust system is equipped with aspark

arrester meeting applicable local or state laws (if any). Ifa spark arrester is used, it

should be maintained in effective working order by the operator.

tn the state of California the above is required by law (Section 4442 of the California

Pubtic Resources Code). Other states may have similar laws. Federal laws apply on

federal lands.

Serial Number:

Date of Purchase:

Gasoline Capacity /Type: 1.5 Quarts (Unleaded Regutar)

OiI Capacity: 20 Ounces

Oil Type (API SG-SL): SAE 30 (above 32°F); SAE 10W-30 (below 32°F)

Spark Plug: Champion 8815 (Gap: .030")

Blade Bolt Torque: 35-40 ft. Ibs.

The model and serial numbers witl be found on a decal on the rear of the lawn mower

housing. Record both serial number and date of purchase in space provided above.

Readtheseinstructionsandthismanualin

its entirety before you attempt to assemble

or operate your new lawn mower,

IMPORTANT: This lawn mower is shipped

WITHOUT OIL OR GASOLINE in the engine,

Your new lawn mower has been assem-

bled at the factory with the exception of

those parts left unassembled for shipping

purposes. To ensure safe and proper

operation of your lawn mower, a]t parts

and hardware you assemble must be tight-

ened securely. Use the correct tools as

necessary to ensure proper tightness. All

parts such as nuts, washers, bolts, etc.,

necessary to complete the assembly have

been p_acedin the parts bag.

TO REMOVE MOWER FROM CARTON

1. Remove loose partsincludedwith

mower.

2. Cut down two end corners of carton

and lay end panel down flat.

3. Remove all packing materials except

padding between upper and lower

handle and padding holding operator

presence control bar to upper handle.

4. Roll lawn mower out of carton and

check carton thoroughly for additional

loose parts.

HOW TO SET UP YOUR MOWER

TO UNFOLD HANDLE

IMPORTANT: Unfold handle carefully so

as not to pinch or damage control cables.

1. Raise handles until lower handle section

locks into place in mowing position.

2. Remove protective padding, raise up-

per handle section into place on lower

handle and tighten both handle knobs.

3. Remove handle padding holding

operator presence control bar to upper

handle.

Your lawn mower handle can be adjusted

for your mowing comfort, Refer to "AD-

JUST HANDLE" in the Service and Adjust-

ments section of this manual.

Operator MOWING

POSITION

controlbar

Upper

UP handle

Handle

knob

Lower handle

TO ASSEMBLE GRASS CATCHER

1, Put grass catcher frame intograss bag

with rigidpart of bag on the bottom.

Make sure the frame handleis outside

ofthe bag top.

2. Slip vinylbindings over frame.

NOTE: Ifvinyl bindings are toostiff, hold

them in warm water for afew minutes. If

bag gets wet, let itdry beforeusing. Frame

Vinyl

bindings Frame

opening

TO INSTALL ATTACHMENTS

Your lawn mower was shippedready to be

usedas a mulcher, To convertto baggingor

discharging,see 'q'O CONVERT MOWER"

in the Operation section of this manual.

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUAL AND ALLSAFETY RULES BEFORE OPERATING

YOUR LAWN MOWER, Compare the illustrationswithyour lawn mowerto familiarize

yourself withthe locationof variouscontrolsand adjustments, Save thismanual for

future reference. m,N=lIN=l=l I

These symbols may appear on your lawn mower or in literature supplied with the

product. Learn and understand their meaning.

CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS

OR WARNING ON OFF AND FEET AWAY

mNllllu I

Operator presence control bar

Handle knob

Starte=

handle Gasoline filler cap

Grass

Air filter

Eng Housing

withdipstick

Mulcher door

Wheeladjuster

(oneachwhee])

IMPORTANT: This lawn mower is shipped

WITHOUT OIL OR GASOLINE in the engine.

i ,n, H =ln

MEETS CPSC SAFETY REQUIREMENTS

Our rotary walk-behind power lawn mowers conform to the safety standards of the

American National Standards Institute and the U.S. Consumer Product Safety Com-

mission. AWARNING-" The blade turns when the engine is running.

i H

Operator presence control bar - must Mulcher door - allows conversionto

be hetddown tothe handle to startthe dischargingor baggingoperation.

engine. Release to stopthe engine. Starter handle - usedforstartingengine.

Theoperationofanylawn

mowercanresultinforeign

objectsthrownintotheeyes,

whichcanresultinsevere

eyedamage.Alwayswear

safetyglassesoreyeshieldswhileoper-

atingyourlawnmoweror performing any

adjustments or repairs, We recommend a

standard safety glasses or widevision safety

mask worn over spectacles.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

Engine speed was set at the factory for

optimum performance. It is not adjustable.

ENGINE ZONE CONTROL

,_IiOAUTION: Federal regulations require

an engine control to be installedon this

lawn mower in order to minimize the

risk of blade contact injury. Do not under

any circumstances attempt to defeat the

function of the operator control. The blade

turns when the engine is running,

• Your lawn mower is equipped with an

operator presence control bar which

requires the operator to be positioned

behind the lawn mower handle to start

and operate the lawn mower.

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower wheels

for high cut, adjust cuttingheighttosuit

your requirements. Medium positionis

best for most lawns.

•To change cutting height, squeeze ad-

juster lever toward wheel. Move wheel

upordown tosuityourrequirements. Be

sure all wheels are inthe same setting.

NOTE; Adjuster isproperlypositionedwhen

plate tab inserts into hole in lever. Also, 9-

positionadjusters(ifsoequipped)al]owlever

to be positioned between the platetabs.

LEVERBACKWARD Platetab

TO LOWERMOWER

LEVERFORWARDTO RAISEMOWER Lever

TO CONVERT MOWER

Your lawn mower was shipped ready tobe

used as amulcher. Toconvertto bagging

or discharging:

REAR BAGGING

*L_ rear doorof the lawn mower and

place the grass catcher frame hooks

onto the doorpivot pins.

• To convertto mulching or discharging

operation, remove grass catcher and

close rear door,

Pivot Rear Grass

catcher

handle

Catcher frame hook

SIDE DISCHARGING

°Rear door must be closed.

•Open mulcher door and install dis-

charge deflector under door as shown,

•Mower is now ready for discharging

operation.

°Toconvert to mulching or bagging opera-

tion, discharge deflector must be removed

and mulcher door must be closed,

SIMPLE STEPS TO REMEMBER WHEN

CONVERTING YOUR LAWN MOWER

FOR MULCHING -

1. Rear doorclosed.

2. Mulcher door closed,

FOR REAR BAGGING -

1. Grass catcher installed.

2. Mulcherdoor closed.

FOR SIDE DISCHARGING -

1, Rear door closed,

_t Discharge deflector installed,

CAUTION: Do not run your lawn mower

without rear door closed, clipping deflector

or approved grass catcher in place. Never

attempt to operate the lawn mower with the

rear door removed or propped open.

Openmulcherdoor

Install

discharge

7 deflector

MOWER IS NOW READY FOR

DISCHARGING OPERATION

TO EMPTY GRASS CATCHER

1. Lift up on grass catcher using the

frame handle,

2. Remove grass catcher with clippings

from under lawn mower handle.

3. Empty clippings from bag.

NOTE: Do not drag the bag when empty-

ing; it will cause unnecessary wear,

G ras8

catcher

frame

handle

BEFORE STARTING ENGINE

ADD OIL

Your lawnmower is shipped without oil in

the engine. For type and grade of oil to

use, see "ENGINE" in the Maintenance

section of this manual.

CAUTION: DO NOT overfill engine with

oil, or it will smoke heavily from the muffler

on startup.

1. Be sure lawnmower is level.

2. Remove oil dipstick from oil fill spout,

3. You receive a container of oil with the

unit. Slowly pour the entire container

down the oil fill spout into the engine.

NOTE: Initial oil fill requires only 18 oz.

due to residual oil in engine from the

manufacturers t00% quality testingo

When changing oil you may need 20 oz.

4. Insert and tighten dipstick.

IMPORTANT:

• Check oil level before each use. Add oil

if needed. Fill to full line on dipstick.

•Change the oil after every 25 hours of

operation or each season. You may

need to change the oil more often

under dusty, dirty conditions. See "TO

CHANGE ENGINE OIL" in the Mainte-

nance section of this manual.

tillercap

Engine

oil cap

ADD GASOLINE

•Fill fuel tank to bottom of tank filler neck.

Do not overfill. Use fresh, clean, regular

unleaded gasoline with a minimum of

87 octane. Do not mix oil with gasoline.

Purchase fuel in quantities that can be

used within 30 days to assure fuel fresh-

ness.

A CAUTION: Wipe off any spilled oil or

fuel. Do not store, spill or use gasoline

near an open flame.

• iLCAUTION: Alcohol blended fuels

(called gasohol or using ethanol or metha-

nol) can atlract moisture which leads to

separation and formation of acids during

storage. Acidic gas can damage the fuel

system of an engine while in storage. To

avoid engine problems, the fuel system

should be emptied before storage of 30

days or longer. Empty the gas tank, start

the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel

next season. See Storage Instructions for

additional information. Never use engine

or carburetor cleaner products in the fuel

tank or permanent damage may occur.

TO STOP ENGINE

• To stop engine, release operator pres-

ence controlbar.

TO START ENGINE

NOTE: Due toprotective coatingson the

engine, a small amount of smoke may be

present duringthe initial use of the product

and should be considerednormal.

NOTE: Your engine is equipped with an

automatic choke system. No priming or

choking isrequired before starting.

•To start engine, hold operator presence

control bar downto the handle and pull

starter handle quickly. Do not allow

starter rope to snap back.

MOWING TIPS

CAUTION: Do not use de-thatcher

blade attachments on your mower. Such

attachments are hazardous, will damage

your mower and could void your warranty.

°Under certain conditions, such as very

tall grass, it may be necessary to raise

the height of cut to reduce pushing effort

and to keep from overloading the engine

and leavingclumps of grass clippings.

It may also be necessary to reduce

ground speed and!or runthe lawn

mower over the area a second time,

*For extremely heavy cutting, reduce the

width of cut by overlapping previously

cut path and mow slowly.

,For better grass bagging and most cut-

ting conditions, the engine speed should

be set in the FAST position.

°Pores incloth grass catcherscan

become filled with dirt and dust with use

and catchers will collect less grass. To

prevent this, regularly hose catcher off

with water and let dry before using.

, Keep top of engine around starter clear

and clean of grass clippings and chaff.

This will help engine air flow and extend

engine life.

MULCHING MOWING TIPS

IMPORTANT: For best performance,

keep mower housing free of built-up

grass and trash. See "CLEANING" in the

Maintenancesection ofthis manual,

, The special mulching blade willrecut

the grass clippingsmanytimes and

reduce them in size so thatas they fall

ontothe lawn they willdisperse into

the grass and not be noticed. Also, the

mulched grass will biodegradequicklyto

providenutrientsfor the lawn, Always

mulchwith your highestengine (blade)

speed as this willprovidethe best recut-

tingaction of the blades.

•Avoid cuttingyour lawn when itiswet.

Wet grass tends to form clumpsand

interfereswiththe mulching action. The

best timeto mow yourlawn isthe early

afternoon. At this time the grass has

dried, yet the newly cut area wiUnot be

exposedto direct sunlight.

•For best results, adjustthe lawnmower

cuttingheightso thatthe lawn mower

cutsoff only thetop one-thirdof the

grass blades, tf the lawnisovergrown

it will be necessaryto raisethe heightof

cut to reduce pushingeffortand to keep

from overloadingthe engine and leaving

clumps of mulched grass. For extremely

heavy grass, reduce your width of cut

by overlapping previously cut path and

mow slowly.

MAX1/3

* Certain types of grass and grass

conditionsmay require that an area be

mulched a second time to completely

hide the clippings. When doing a sec-

ond cut, mow across (perpendicular) to

the first cut path.

- Change your cutting pattern from week

to week. Mow north to south one week

then change to east to west the next

week. This will help prevent matting

and graining of the lawn.

MAINTENANCE AFTER

EACH 10

USE HOURS

EVERY EVERY

25 HOURS 100

OR SEASON HOURS

HI i /

v'3

qv_,2

BEFORE

EACH

USE

iii i,i illl

Check for Loose Fasteners If

_ "Clean /Inspect Grass Catcher * _ I_

Check Tires I/

IM 'Check Drive Wheels "*" t/

Clean Lawn Mower **** If

MClean under Drive Cover "*" ....... t_

OCheck Drive Belt /Pulleys ***

_ Check /Sharpen /Replace Blade

Lubrication ..........

RClean and Recharg,e_.8artery ** ll,lll

Check Engine Oi! level I_s

_1 Change Engine Oil .........

c_eanAi__ilier ....

_ inspect , .......

Muffler

NReplace.Spark Plug V'

E Replace Air Filter Paper Cartridge I_

i Empty fue,I,,system or add Stabilizer .......... ...............i_

I - Change more often if operating under a heavy load or in high outdoor temperatures,

2- Service more often if operating in ditty or dusty conditions,

3- Replace blades more often when mowing in sandy soil.

4 - Charge 48 hours at end of season.

5- And after each 5 hours of use,

* (if so equipped)

** Electric-Start mowers

*** Power-Propelled mowers

**** Use ascraper

to clean ut_der deck

BEFORE

STORAGE

GENERAL RECOMMENDATIONS

The warranty on this lawn mower does not

cover items that have been subjected to

operator abuse or negJigence. Toreceive

full value fromthe warranty, operator must

maintain unit as instructed in this manual.

LUBRICATION CHART

Wheel

adjuster (on

each wheel)

Some adjustments will need to be made

periodically to properly maintain your unit.

At least once aseason, check to see if

you should make any of the adjustments

described in the Service and Adjustments

section of this manual.

•At least once a year, replace the spark

plug, clean or replace air filter element

and check blade for wear. A new spark

plug and clean/new air filter element

assure proper air-fuel mixture and heip

your engine run better and last longer.

• Follow the maintenance schedule in this

manual

BEFORE EACH USE

•Check engine oil level.

•Check for loose fasteners.

LUBRICATION

Keep unit well lubricated

(See "LUBRICATION CHART").

Engine oil

(_ Mulcher

door hinge

(_ Rear door

hinge

(_ Handle bracket mounting pins

_Spray lubricant

See "ENGINE" in Maintenance section.

IMPORTANT; Do not oil or grease plastic

wheel bearings. Viscous lubricants wilt

attract dust and dirtthat willshorten the life of

the self-lubricating bearings, lfyou feel they

must belubricated, use onlyadry, powdered

0graphite type lubricant sparingly.

Autres manuels pour A149K21 (96136300)

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Ariens Tondeuse à gazon

Ariens

Ariens Sno-Thro 932500-520 Manuel du propriétaire

Ariens

Ariens IKON-XD Series Manuel utilisateur

Ariens

Ariens A20K46YT Manuel du propriétaire

Ariens

Ariens 911150 - BRP21 Manuel utilisateur

Ariens

Ariens 936031 - 2048 Manuel utilisateur

Ariens

Ariens Grand Sierra GT 831026 Manuel utilisateur

Ariens

Ariens Imperial RM1028 Manuel du propriétaire

Ariens

Ariens 931000 Manuel utilisateur

Ariens

Ariens Grand Sierra 931038 Manuel du propriétaire

Ariens

Ariens 927 Manuel utilisateur

Ariens

Ariens Razor 911173 Manuel utilisateur

Ariens

Ariens A173K22 (96136100) Manuel utilisateur

Ariens

Ariens Contractor 996126 Manuel utilisateur

Ariens

Ariens 935 Series Manuel utilisateur

Ariens

Ariens 911207 Pro21XD, 911214 Pro21XD Manuel du propriétaire

Ariens

Ariens 927 Manuel utilisateur

Ariens

Ariens Razor 911173 Manuel utilisateur

Ariens

Ariens 915037 Manuel utilisateur

Ariens

Ariens EZRider 008-1540 Manuel du propriétaire

Ariens

Ariens GRAVELY Pro Unit HR1536FX Manuel du propriétaire

Ariens

Ariens Promaster PM144Z Manuel du propriétaire

Ariens

Ariens A160H22 (96146000) Manuel d'utilisation et d'entretien

Ariens

Ariens Apex 60 Manuel utilisateur

Ariens

Ariens 1742 EZR Manuel du propriétaire

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur