ARGON18 MY2016 Nitrogen Pro Manuel utilisateur

NITROGEN PRO: ASSEMBLY GUIDE

Valid for MY2016 Nitrogen Pro

Revision 7.0 - 04-01-2016

1. Frame Inspection . . . . . . . . . . . . . . . . . . . . . ...................2

2. Frameset Parts . . . . . . . . . . . . . . . . . . . . . ......................3

3. Headset Installation . . . . . . . . . . . . . . . . . . . . ..................5

4. Stem/Handlebar Installation . . . . . . . . . . . . . . . . . . . . ..........8

5. Front Brake Installation. . . . . . . . . . . . . . . . . . . . . . . . . . ........16

6. Rear Brake Installation . . . . . . . . . . . . . . . . . . . . . . ............20

7. Cable Housing Installation . . . . . . . . . . . . . . . . . . . . . . . . . .....22

8. Electronic Drive-train Specication . . . . . . . . . . . . . . . . . .. . . .28

9. Seatpost Installation. . . . . . . . . . . . . . . . . . . . . . . . . ...........32

10. Saddle Adjustment . . . . . . . . . . . . . . . . . . . . . . . .............33

11. Derailleur Hanger Adjustment. . . . . . . . . . . . . . . . . . . . . . . . ..34

12. Frameset Parts Checklist . . . . . . . . . . . . . . . . . . . . . . . ........36

For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,

particularly carbon parts, need extra care when assembled. These components must be installed using a calibrated torque

wrench to make sure every bolt is at the right torque setting to prevent damage.

NITROGEN PRO: Table of Contents

My Nitrogen Pro

Date of purchase:

Retailler:

Size:

Serial Number:

Parts installed on the frame Description Screw Tork Detail

type Nm

1 Front derailleur hanger Screw (2) 3mm 4Nm Loctite

2 Rear derailleur hanger Screw (2) 3mm 4Nm Loctite

3 Bottle cage Screw (4) 4mm 3Nm Grease

4 Bottom bracket cable guide Screw 5mm 1.5Nm Grease

IMPORTANT:

The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their torque

speciﬁcations.

NITROGEN PRO: 1. Frame Inspection

BEFORE ASSEMBLING YOUR NEW NITROGEN PRO, MAKE SURE THAT YOU HAVE ALL THE FOLLOWING:

1. Brakes and gears cables and housing set

2: Frameset parts checklist (see p.36)

3: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)

4: For reference, check serial number and write it on p.1

5: All the necessary bolts (refer to Frameset Parts, p.3)

6: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is

straight (p.35)

NITROGEN PRO: 2. Frameset Parts

Images are for reference only. Proportions are not accurate.

Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.

17 18

15 4 514 13

109

67128

17b

17f

17a

17g

17d

17e

17c

17h

17i

17h

17i

17h 18b

18f

18a

18g

18d

18e

18c

18h

18i

18h

18i

18h

Brake & derailleur

cable / housing kit

JB527AR01, JD527AR01

NITROGEN PRO: 2. Frameset Parts

AHB5000 (38cm, 40cm, 42cm, or 44cm)

Spacer

20mm

Stem A.03

Large

Stem A.02

Medium

Stem A.01

Small

Elastic Cover

Large

Elastic Cover

Small

Washer

Screw

M8x50mm

Screw

M8x30mm

Screws

M5x16mm

23 24 25 26 27 28 29 30 31 32

Frameset Handlebar Width

Stem Size 20mm

Size 38 40 42 44 Small Medium Large Spacer

X-Small

Small

Medium

Large

X-Large

Notes: 38cm Handlebar is only available aftermarket.

If you wish to purchase the third non-included stem, you can do so by ordering it as a spare part

Install the 3D headset (16) according to

the AERO Presst assembly guide. You can

choose from 3 dierent heights: 25mm,

15mm or 0mm.

NITROGEN PRO: 3. Headset Installation

GREASE

NITROGEN PRO: 3. Headset Installation

25mm

15mm

0mm

setup

5 5

Compressor

Top cap (including O-ring & seal)

Micro spacers

Compression ring

Bearing

3D bearing holder

Plastic sleeve (no need for 0mm setup)

Top cap for 0mm setup

head tube

(bike)

head tube

(bike)

head tube

(bike)

To remove the 3D bearing holder, insert the Park Tool

RT-1 and then tap it carefully until the spacer comes out.

STEP

Inspect the bike’s head tube for any sharp edges and

apply a small amount of grease.

STEP

For the 25mm and 15mm setups, lightly grease the

bottom section of the 3D bearing holder (6) and insert

the plastic sleeve (7).

STEP

Position the headset inside the head tube. Place

the top 3D assembly with the headset bearing inside

(this will prevent the sleeve from getting damaged).

Add the compression ring on top of the bearing, then

add the press t 3D system tool and softly press down

the assembly until it bottoms out using a Bearing Cup

Press (Park Tool HHP-2). Then, insert the bottom

bearing (5), compression ring (4) micro spacers (3) and

top cap (2), slide the fork and stem and measure the

steerer length needed.

For the 0mm setup , do not use the plastic sleeve.

Install the 3D bearing holder (6) with grease applied

directly inside the frame.

STEP

First, you must assess which setup suits your needs:

25mm, 15mm or 0mm.

NITROGEN PRO: 3. Headset Installation

Compressor

Top cap (including O-ring and seal)

Micro spacers

Compression ring

Bearing

3D bearing holder

Plastic sleeve (no need for 0mm setup)

Top cap for 0mm setup

Press Fit 3D system tool 1 1/4”

Bearing Cup Press (Park Tool HHP-2)

IMPORTANT: Use the Press Fit 3D system tool 1 1/2” with

the Bearing Cup Press (ParkTool HHP-2) to avoid any

damage on the bike frame.

NITROGEN PRO: 4. Stem/Handlebar Installation

Handlebar Width (cm)

Stems size (stems included)

S M L 20mm spacer

CONFIGURATION MATRIX

If you wish to purchase

the third non-included

stem, you can do so by

ordering it as a spare

part.

Failure to use long

screw when assembling

bar with +20mm spacer

of any conguration can

lead to serious injury

NITROGEN PRO: 4. Stem/Handlebar Installation

1. Choose the desired stem length, bolt, and spacer

needed (refer to the Product Matrix chart on p.X) – note

that the bolt comes pre-coated with Loctite. In the event

of assembling and disassembling, one drop of blue

Loctite (#242 or #243) must be applied on the bolt

threads.

Autres manuels pour MY2016 Nitrogen Pro

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ARGON18 Vélo

ARGON18

ARGON18 GALLIUM PRO DISC 338A Manuel utilisateur

ARGON18

ARGON18 E-119 TRI+ Manuel utilisateur

ARGON18

ARGON18 GALLIUM DISC 280A Manuel utilisateur

ARGON18

ARGON18 SUM PRO 2022 Manuel utilisateur

ARGON18

ARGON18 RADON 237A Manuel utilisateur

ARGON18

ARGON18 GALLIUM CS DISC 322A Manuel utilisateur

ARGON18

ARGON18 KRYPTON 212A Manuel utilisateur

ARGON18

ARGON18 GALLIUM PRO DISC 338A 2021 Manuel utilisateur

ARGON18

ARGON18 E-112 Manuel utilisateur

ARGON18

ARGON18 KRYPTON XROAD 213C Manuel utilisateur

ARGON18

ARGON18 nitrogen Manuel utilisateur

ARGON18

ARGON18 GALLIUM CS DISC 362A Manuel utilisateur

ARGON18

ARGON18 GALLIUM 260A Manuel utilisateur

ARGON18

ARGON18 E-80 Manuel utilisateur

ARGON18

ARGON18 GALLIUM 348A Manuel utilisateur

ARGON18

ARGON18 GALLIUM 279A Manuel utilisateur

ARGON18

ARGON18 MY2016 Nitrogen Pro Manuel utilisateur

ARGON18

ARGON18 E-118 NEXT Manuel utilisateur

ARGON18

ARGON18 E-118 NEXT Manuel utilisateur

ARGON18

ARGON18 E-117 TRI+ Manuel utilisateur

ARGON18

ARGON18 KRYPTON GF 273A Manuel utilisateur

ARGON18

ARGON18 Grey Matter Manuel utilisateur

ARGON18

ARGON18 Road Racing Manuel utilisateur

ARGON18

ARGON18 Dark Matter Manuel utilisateur

Manuels Vélo populaires d'autres marques

RAMBO

RAMBO R1000X2M-FF-BFD Manuel utilisateur

Vermeiren

Vermeiren SAFARI Manuel utilisateur

Velec

Velec A2/36V Manuel utilisateur

Coswheel

Coswheel A-ONE Manuel utilisateur

Betzold

Betzold 97869 Manuel utilisateur

Cervélo

Cervélo S3 2019 Manuel utilisateur

Tenways

Tenways AGO X Manuel utilisateur

Festo

Festo EGSC-BS-KF Manuel de la liste des pièces

Gio Electric

Gio Electric H1 Volt Manuel utilisateur

GOGOBEST

GOGOBEST GM30 Manuel utilisateur

DAHON

DAHON CIAO - 2009 Manuel utilisateur

Aprimatic

Aprimatic ONDA 500 Guide de démarrage rapide

MV Agusta

MV Agusta Lucky Explorer GRAVEL Manuel d'instructions

Greyp

Greyp G6 Series Manuel utilisateur

Babboe

Babboe Carve-E Manuel utilisateur

Huka

Huka orthros Manuel utilisateur

Xtracycle

Xtracycle Stoker 2021 Manuel utilisateur

APRILIA

APRILIA DORSODURO 750 ABS 2015 Manuel utilisateur