Arecont Vision AV1255AM Manuel utilisateur

Installation Manual

Wide Angle Models:

AV1255AM AV3256PM

AV1255AM-H AV3256PM-A

AV1255AMIR AV3256PMIR

AV1255AMIR-H AV3256PMIR-S

AV1255PM-SH AV3256PMIR-SA

AV1255PMIR-SH

AV2255AM AV5255AM

AV2255AM-A AV5255AM-A

AV2255AM-H AV5255AM-H

AV2255AM-AH AV5255AM-AH

AV2255AMIR AV5255AMIR

AV2255AMIR-A AV5255AMIR-A

AV2255AMIR-H AV5255AMIR-H

AV2255AMIR-AH AV5255AMIR-AH

AV2255PMIR-SH AV5255PMIR-SH

AV2255PMIR-SAH AV5255PMIR-SAH

AV2256PM

AV2256PMIR

AV2256PMIR-S

AV3255AM AV10255AMIR

AV3255AM-H AV10255AMIR-H

AV3255AMIR AV10255PMIR-SH

AV3255AMIR-H

AV3255PMIR-SH

IR Motorized Model

DN Motorized Model

Arecont Vision MegaDome®2 Installation Manual

Page | 2 support@arecontvision.com

Telephoto Models:

AV2255PMTIR-H

AV2255PMTIR-SH

AV2256PMTIR-S

AV3255PMTIR-H

AV3255PMTIR-SH

AV3256PMTIR

AV3256PMTIR-S

AV5255PMTIR-H

AV5255PMTIR-SH

AV10255PMTIR-H

AV10255PMTIR-SH

Manual Lens Models:

AV1255DN

AV1255DN-H

AV2255DN

AV2255DN-H

AV2256DN

AV3255DN

AV3255DN-H

AV3256DN

AV5255DN

AV5255DN-H

IR Telephoto Motorized Model

Manual Lens Model

Arecont Vision MegaDome®2 Installation Manual

Page | 3 support@arecontvision.com

MegaDome®2 Installation

Contents

Package Contents................................................................................................................................................... 4

Warranty Information.............................................................................................................................................. 5

Installation................................................................................................................................................................ 6

Camera Discovery................................................................................................................................................... 9

Web Interface Quick Guide.................................................................................................................................. 13

SD Card Functionality........................................................................................................................................... 20

Installation Best Practice...................................................................................................................................... 24

Wall Mount (MD-WMT2) Installation Instructions (Sold Separately)............................................................. 25

Junction Box Adapter (SV-JBA) Installation Instruction (Sold Separately).................................................. 26

Electrical Box Adapter (SV-EBA) Installation Instructions (Sold Separately).............................................. 30

Pole Mount Adapter (AV-PMA) Installation Instructions (Sold Separately).................................................. 31

Corner Mount Adapter (AV-CRMA) Installation Instructions (Sold Separately) .......................................... 32

LED Indicators (Camera Signal)......................................................................................................................... 36

Support ................................................................................................................................................................... 37

Mounting Template............................................................................................................................................... 38

Arecont Vision MegaDome®2 Installation Manual

Page | 4 support@arecontvision.com

Package Contents

MegaDome®2 Camera Package:

A. Arecont Vision MegaDome® 2 camera

B. Mounting template

C. CD with AV100 software and user manuals (License Key Required for Recording)

D. AC & DC power cable

E. I/O cable

F. Pack of four (4) screws and four (4) anchors

NOTE: Anchors and screws are good to be used for concrete, wall block and red bricks.

NOTE: Screws by themselves can be used in wood.

G. Security L-Key

H. One double-sided hex key

I. One single-sided hex key

J. Magnetic core

Image 1

Important Notes:

1. Camera Operating Temperature:

-40°C (-40°F) to +50°C (122°F) w/ Heater (-H models) or WDR Models

-20°C (-4°F) to +50°C (122°F) w/o Heater

2. Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and

with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or

Recognized wire suitable for the application.

3. Always use hardware e.g. screws, anchors, bolts, locking nuts etc. which are compatible with

mounting surface and of sufficient length and construction to insure a secure mount.

Warranty Information

3 Year Limited Warranty

ARECONT VISION warrants to Purchaser (and only Purchaser) (the “Limited Warranty”), that: (a) each Product shall be free

from material defects in material and workmanship for a period of thirty-six (36) months from the date of shipment (the

“Warranty Period”); (b) during the Warranty Period, the Products will materially conform with the specification in the applicable

documentation; (c) all licensed programs accompanying the Product (the “Licensed Programs”) will materially conform with

applicable specifications. Notwithstanding the preceding provisions, ARECONT VISION shall have no obligation or

responsibility with respect to any Product that (i) has been modified or altered without ARECONT VISION’s written

authorization; (ii) has not been used in accordance with applicable documentation; (iii) has been subjected to unusual stress,

neglect, misuse, abuse, improper storage, testing or connection; or unauthorized repair; or (iv) is no longer covered under the

Warranty Period. ARECONT VISION MAKE NO WARRANTIES OR CONDITIONS, EXPRESS, IMPLIED, STATUTORY OR

OTHERWISE, OTHER THAN THE EXPRESS LIMITED WARRANTIES MADE BY ARECONT VISION ABOVE, AND

ARECONT VISION HEREBY SPECIFICALLY DISCLAIMS ALL OTHER EXPRESS, STATUTORY AND IMPLIED

WARRANTIES AND CONDITIONS, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, NON-INFRINGEMENT AND THE IMPLIED CONDITION OF SATISFACTORY QUALITY. ALL

LICENSED PROGRAMS ARE LICENSED ON AN “AS IS” BASIS WITHOUT WARRANTY. ARECONT VISION DOES NOT

WARRANT THAT (I) THE OPERATION OF THE PRODUCTS OR PARTS WILL BE UNINTERRUPTED OR ERROR FREE;

(II) THE PRODUCTS OR PARTS AND DOCUMENTATION WILL MEET THE END USERS’ REQUIREMENTS; (III) THE

PRODUCTS OR PARTS WILL OPERATE IN COMBINATIONS AND CONFIGURATIONS SELECTED BY THE END USER;

OTHER THAN COMBINATIONS AND CONFIGURATIONS WITH PARTS OR OTHER PRODUCTS AUTHORIZED BY

ARECONT VISION OR (IV) THAT ALL LICENSED PROGRAM ERRORS WILL BE CORRECTED.

For RMA and Advance Replacement information visit ArecontVision.com

Arecont Vision MegaDome®2 Installation Manual

Page | 6 support@arecontvision.com

Installation

Mounting the Camera:

1. Remove the camera and hardware from

the box.

2. Using the mounting template, prepare the

mounting surface for camera installation.

NOTE: the 19.5mm diameter hole on the

Mounting template is where the Ethernet

cable will be exiting the MegaDome®2

align accordingly. If using the side conduit

hole, please see step 4 following.

3. Using Security L-key, loosen the four (4)

screws securing the dome cover (Image 2).

Remove the vandal resistant dome cover.

NOTE: Do not remove the screws from the

dome cover.

Image 2

4. If you are using the side conduit

opening, remove the conduit plug by

first removing the socket set screw

using the provided double-sided hex

key (Image 3).

Image 3

Note: Make sure that you install the rubber

gasket on the bottom of the camera to form

a weather tight seal with the mount

surface.

5. Run the Ethernet cable through the gasket

and the hole on the bottom of the camera

(Image 4) or run the cable through the side

conduit and plug it into the RJ45 port.

NOTE: If the camera will be powered via

PoE, please skip to step 6.

6. If the camera will be powered by an AC or

DC power supply, run the supplied power

cable through the gasket and the hole on

the bottom of the camera or run the cable

through the side conduit and connect it to

its respective connector inside the camera

(Image 3).

NOTE: Make sure that your installation of

wires complies with Electrical Code of the

local government where the camera is

installed and that no bare wires are

exposed.

Arecont Vision MegaDome®2 Installation Manual

Page | 7 support@arecontvision.com

Image 4

7. Align the holes in the camera with the

prepared holes on the mounting surface.

Attach the camera to the mounting surface

with the wood screws or any optional

hardware suitable for the mounting

surface.

8. Use appropriate mounting accessories to

ensure a water tight installation. Use of

silicon does not guarantee a water

resistant install.

Adjusting the Tilt, Pan, Z-Axis

(yaw):

9. To adjust the tilt, use a #1 Phillips

screwdriver to loosen the screw on the side

of the plastic lens bracket 1/4 turn (Image

5).

CAUTION: Do not remove the screw!

10. Adjust lens tilt as required and tighten the

screw.

11. To adjust the pan, use a #2 Phillips

screwdriver to loosen the screw as shown

in Image 5.

CAUTION: Do not remove the screw.

12. Adjust the pan as required and tighten the

screw.

13. To adjust the Z-Axis, or yaw, for vertical

wall mounting, loosen the set screw as

shown in Image 5.

NOTE: There are two set screws on opposite

sides; both need to be loosened.

CAUTION: Do not remove the screw.

14. Adjust the Z-Axis as required and tighten

the set screws.

Image 5

HOLE

POWER

RJ-45

Z-Axis

(Yaw)

Tilt

Pan

Arecont Vision MegaDome®2 Installation Manual

Page | 8 support@arecontvision.com

Image 6

15. If the camera is manual lens model, loosen

the three set screws as shown in Image 6

and adjust zoom, focus and iris as needed.

Securing the Vandal Dome Cover:

16. Adjust black liner position to avoid blocking

IR light (if equipped) or the lens as shown

in Image 7.

17. Remove the protective film from the

camera dome.

NOTE: Be careful not to scratch the vandal

dome cover.

18. Secure the vandal dome cover to the

camera using the provided security L-Key.

Image 7

Black Liner

IR LEDs

Zoom

Focus

Iris

Arecont Vision MegaDome®2 Installation Manual

Page | 9 support@arecontvision.com

Camera Discovery

1. Install the AV200 application manager

Software found on the CD.

NOTE: you can download latest version AV200

and installation manual on website

http://www.arecontvision.com/softwares.php

2. Running the Program Installer

To begin the installation of the AV200

software, launch the AVSysSetup.msi

installer (double-click or right click and

chose Open).

This will start the installation and is followed

by the installation welcome screen.

Click next and follow the AV200 Setup

Wizard to install the AV200.

3. Adding Cameras with System Setup Wizard

After the AV200 is installed, the first time it

is launched the System Setup Wizard will

be started.

Anytime you wish to re run the setup wizard

in the future you can access it from your

desktop by clicking on the icon called

“AVSysSetup”.

The first screen the wizard displays is the

welcome screen.

Click next to continue. Following the

welcome screen, the Accounts screen will

ask to set up Administrator and User

passwords.

Arecont Vision MegaDome®2 Installation Manual

Page | 10 support@arecontvision.com

An Administrator password must be set and

confirmed. The wizard will not allow a blank

password for Administrator and setup

cannot proceed without setting one.

User password can be left blank, allowing

standard users to launch the application

without a password. Click Next to continue.

The next screen in the wizard is the camera

discovery page.

A range of IP addresses can be defined to

apply to the cameras. If unchanged, the

default address range will be defined by the

IP address currently assigned to the

computer. The second IP range means

cameras within this range will be not

selected by default. No changes will be

made to any cameras not selected (see

next wizard page).

Click Next to continue.

The following screen will display a list of

cameras discovered on the network.

The Refresh button provides an option to

make sure all cameras are found or to

rediscover cameras that were connected

after wizard started.

If Refresh is selected, the wizard will display

the discovery screen while it searches for

cameras on the network.

If you have recording licenses click the

button called “Import licenses” to browse to

the folder on your computer the license files

are located. As example if you had licenses

for cameras previously in AV100 software

they will usually be found in the “C:\Program

Files\Arecont Vision\Video

Surveillance\license” directory.

After the license files are successfully

imported you will see the following pop up

display.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Arecont Vision Caméra de sécurité

Arecont Vision

Arecont Vision SurroundVideo Omni AV12176DN-NL Manuel utilisateur

Arecont Vision

Arecont Vision AV12275DN-NL Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo Flex Series Manuel utilisateur

Arecont Vision

Arecont Vision Megaball series Manuel utilisateur

Arecont Vision

Arecont Vision AV08ZMV-300 Manuel utilisateur

Arecont Vision

Arecont Vision ConteraIP Fisheye AV12CPD-236 Manuel utilisateur

Arecont Vision

Arecont Vision D4SO Series Manuel utilisateur

Arecont Vision

Arecont Vision AV12975DN-NL Manuel utilisateur

Arecont Vision

Arecont Vision AV2100 Manuel utilisateur

Arecont Vision

Arecont Vision AV12ZMV-301 Manuel utilisateur

Arecont Vision

Arecont Vision MicroDome AV1455DN-S Manuel utilisateur

Arecont Vision

Arecont Vision H.264 Day/Night SurroundVideo Series Manuel utilisateur

Arecont Vision

Arecont Vision Contera Micro Bullet Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall 2 Manuel utilisateur

Arecont Vision

Arecont Vision MicroDome G2 AV1555DN-S Manuel utilisateur

Arecont Vision

Arecont Vision MicroDome AV2455DN-S Manuel utilisateur

Arecont Vision

Arecont Vision MicroDome AV1455DN-F Manuel utilisateur

Arecont Vision

Arecont Vision MegaDome G3 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV2245PM-W Manuel utilisateur

Arecont Vision

Arecont Vision AV2325DNIR Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV2245PM-W Manuel utilisateur

Arecont Vision

Arecont Vision MicroDome Manuel utilisateur

Arecont Vision

Arecont Vision Contera AV02CLB-100 Manuel utilisateur

Arecont Vision

Arecont Vision D4S Series Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur