Arecont Vision AV12186DN SurroundVideo Manuel utilisateur

Arecont Vision AV12186DN SurroundVideo® Installation Manual

1 | Page

Arecont Vision AV12186DN SurroundVideo® Installation Manual

1 | Page

AV12186DN SurroundVideo®Installation Manual

A. Arecont Vision AV12186DN camera

Inside the box:

B. Mounting template

C. Security L-key

D. 1.5mm Hex L-key

E. Power cable

F. I/O Cable

G. Pack of four (4) wood screws and four (4)

dry wall anchors.

•#2 Phillips head screw driver

Not included but needed:

Image 1

How to Mount the Camera

1. Remove camera and hardware from the

box.

2. Using the Mounting template, prepare the

mounting provisions for camera

installation. NOTE: the 19.5mm diameter

hole on the Mounting template is where

the Ethernet cable will be exiting the

AV12186DN camera, align accordingly.

If using the side conduit hole, please see

step 7below.

3. Using Security L-key, loosen the four (4)

screws securing the dome cover (Image 2).

Remove vandal resistant dome cover. NOTE:

Do not remove screws from the dome cover.

RJ-45

POWER

HOLE

Arecont Vision AV12186DN SurroundVideo® Installation Manual

2 | Page

Image 2

4. Run Ethernet cable through the hole on the

bottom of the camera (Image 3) and plug it

into the RJ45 port.

5. If the camera is powered by a separate

outside AC or DC power source, run the

supplied power cable through the hole and

connect it to 2-pos. AC/DC power connector

inside the camera (Image 3). NOTE: Make

sure that your installation of wires complies

with Electrical Code of the local government,

where the camera is installed and no bare

wires are exposed.

6. Align the holes in the camera with the

prepared holes on the mounting surface.

Attach the camera to the mounting surface

with the wood screws or any optional

hardware suitable for the mounting surface.

Image 3

7. If you are using the side conduit opening,

remove the conduit plug by first removing the

socket set screw using 1.5mm Hex L-key

(Image 4).

Image 4

HOLE

POWER

RJ-45

Arecont Vision AV12186DN SurroundVideo® Installation Manual

3 | Page

Image 5

8. To adjust the tilt, use #2 Phillips screwdriver to

loosen two screws on both sides of the Gimbal, no

more than two full turns (Image 5)

CAUTION: Do not remove the screws!

Adjust Camera Tilt, Pan and Focus:

CAUTION: Make sure the sensor cables are

freely moving in cable slot, the correct way to

tilt the Gimbal is shown on Image 6.

9. Adjust lens tilt as required and tighten the

screw from step 8

10. To adjust the Pan simply rotate the gimbal.

The friction ring at the bottom of the gimbal

doesn’t require any hardware. NOTE: Grab

gimbal by the brackets, not the ball to avoid

direct contact with lenses not to damage them

or leave fingerprints on glass.

11. To focus each of four lenses, remove the lens

cap and focus the lens as shown in Image 7.

Note, the wave washer underneath the lens

prevents it from losing focus in vibration.

12. Remove the protective film from the camera

dome. NOTE: be cautious not to scratch the

vandal-resistant dome cover.

13. Secure the vandal dome cover to the camera

as shown in Image 2.

Image 6

CORRECT

SLOT

POSITION

Arecont Vision AV12186DN SurroundVideo® Installation Manual

4 | Page

Image 7

Camera Installation:

14. Install the AV100 application manager

Software as shown in Image 8 (found on

the CD).

15. Run the AV100 application manager by

double clicking on the icon as shown in

Image 9(found on your desktop).

Image 8Image 9

16. Select “Run” next to “Setup Cameras”

from the AV100 application manager as

shown in Image 10 and wait for “Arecont

Vision Camera Installer” window to appear

as shown in Image 11.

Image 10

17. Click “Mode” tab to select desired install

mode on Arecont Vision Camera Installer

as shown in Image 11.

NOTE 1: Basic Mode (default setting): software

will automatically discover and change / assign

IP address to match PC subnet.

NOTE 2: Advanced Mode: software will

automatically discover but allow manual update

of the IP address. See “AV100 Installation

Manual” (found on the CD) for details on

Advanced Mode.

Image 11

Arecont Vision AV12186DN SurroundVideo® Installation Manual

5 | Page

18. In Basic Mode select “Install Cameras” on

Arecont Vision Camera Installer as shown

in Image 11

19. Confirm all cameras connected to the

network switch appear in the upper

window.

20. Repeat Step 22 if all of the cameras do

not appear in the upper window.

CAUTION: If the software does not find a

camera, the software utility may be blocked by

the anti-virus or Windows®

firewall. Before

turning them off, please consult your IT

manager.

NOTE : Double click the camera model on the

Camera Installer as shown in Image 12 to

access the camera web interface.

See “AV Camera Web Page User Manual”

(found on the CD) for details on the web

interface.

Image 12

21. When all cameras appear, select

“Save/Exit.” The AV100 application will

appear.

22. From the “AV100 Application Manager”

menu, select “Run” to view live images.

NOTE: See the “AV100 Installation Manual”

(found on CD) for details on camera

configurations.

Arecont Vision AV12186DN SurroundVideo® Installation Manual

6 | Page

Image equalization (exposure reference) instructions:

1. Launch the camera webpage

2. Click “Setting” and select the desired channel to be the cameras “Exposure Reference Channel” (see

Image 13). Setting an Exposure Reference Channel will reduce the color and brightness variations

among channels. Channel numbers are shown in Image 14.

Image 13

NOTE: The default setting for the “Exposure Reference Channel” is “Auto”, which means that each channel

is automatically adjusted to provide the best WDR scene. This may cause variations from image to image,

however the camera is providing the best image for each channel. When different channels are under

different lighting conditions, there will be some color or brightness variation among the channels. See below

for an example on how to adjust different reference channels to minimize brightness and color differences.

NOTE: Using Exposure Reference Channel Setting may result in abnormal noise which can’t be resolved!

Image 14

Arecont Vision AV12186DN SurroundVideo® Installation Manual

7 | Page

- Exposure Reference Channel set as “Auto”

- Exposure Reference Channel set as Channel “1”

- Exposure Reference Channel as Channel “2”

Image 15

Arecont Vision AV12186DN SurroundVideo® Installation Manual

8 | Page

Since AV12186DN camera utilizes

the same housing as MegaDome®

it also shares the same

accessories.

Image 16

MD-CMT

MD-CAP

MD-WMT2

MD-CRMA

MD-PMA

SV-EBA

SV-JBA FOR

MD-WMT2

MD-EBA

Arecont Vision AV12186DN SurroundVideo® Installation Manual

9 | Page

MegaDome®

Pendant Mount (MD-CMT) Installation Instructions

A. Top shield

Inside the box:

B. Pendant Mount

C. Mounting template

D. Pack of four (4) machine screws

E. Pack of four (4) small machine screws

F. Pack of four (4) wood screws and four (4)

dry wall anchors

G. Large round rubber gasket

H. Smaller square rubber gasket

I. One double sided hex key

J. #2 Phillips head screw driver

Not included but needed:

Image 17

23. Remove Pendant Mount and hardware from

the box.

Image 18 Image 19

24. Using Mounting template, prepare the

mounting provisions for camera installation.

25. Place small gasket onto pendant dome as

shown in image 18.

26. Attach Dome to Pendant as shown in Image

19 using four machine screws provided.

27. Install large round rubber gasket onto

Pendant as shown in image 19. Be sure to

align the holes appropriately.

28. Run Ethernet Cable and outside power cable

(if necessary) through the Pendant.

29. Attach Pendant to the ceiling using the four

wood screws provided or any optional

hardware suitable for the mounting surface.

30. For installation of the camera, please

reference “Mounting the Camera”.

Autres manuels pour AV12186DN SurroundVideo

Autres manuels Arecont Vision Caméra IP

Arecont Vision

Arecont Vision Surround Video AV8185 Manuel utilisateur

Arecont Vision

Arecont Vision AV3110 Manuel utilisateur

Arecont Vision

Arecont Vision AV20185DN Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV5110 Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV2105 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Arecont Vision

Arecont Vision MegaDome AV1355 Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV5100-AI Manuel utilisateur

Arecont Vision

Arecont Vision AV10005 Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV3130 Manuel utilisateur

Arecont Vision

Arecont Vision Surround Video AV8365 Manuel utilisateur

Arecont Vision

Arecont Vision MegaDome AV2155 Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV3100-AI Manuel utilisateur

Arecont Vision

Arecont Vision AV10005DN Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV1305 Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV1300 Manuel utilisateur

Arecont Vision

Arecont Vision AV5100M Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV2100-AI Manuel utilisateur

Arecont Vision

Arecont Vision AV12186DN SurroundVideo Manuel utilisateur

Arecont Vision

Arecont Vision MegaDome AV3155 Manuel utilisateur

Arecont Vision

Arecont Vision MegaVideo AV3105 Manuel utilisateur

Arecont Vision

Arecont Vision MicroDome AV1455DN-S Manuel utilisateur

Arecont Vision

Arecont Vision MegaDome AV5155 Manuel utilisateur

Arecont Vision

Arecont Vision Surround Video AV8180 Manuel utilisateur

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur

Digitus

Digitus DN-16085-1 Manuel utilisateur