Arbiter Systems 921A Mode d’emploi

PD0020500A

Arbiter Systems, Inc

Model 921A Combustible Gas Meter

Filter Replacement Instructions

Equipment Required

1. Annual Filter Maintenance Kit, P/N: AS0035100, which includes the following:

-Breather Filter (1 each)

-Particulate Filters (5 each: 3 internal, 2 external replacements).

-Transformer In-Line Filter Kit, P/N: AS0026900 (1 each)

2. T10 TorxDriver

3. ¼” open-end wrench.

Procedure

To replace the Model 921A internal filters perform the following steps:

1. Using a T10 Torxdriver, remove the fourcorner screws from the rear panel.

2. Locate the three Particulate Filters (blue/white).

NOTE: Three Particulate Filters replace the Model 921A internal filters and the remaining two

are intended to replace those used externally when performing measurements. Replace the

Particulate Filters one at a time so that the corresponding flexible tubing removed is replace on

the correct filter. Gently move adjacent flexible tubing aside when disconnecting filter.

3. Disconnect the Particulate Filter using the plastic twist-lock Luer fitting. Gently remove the

fitting and attached tubing from the filter.

WARNING: DO NOT over tighten or use extreme downward pressure when re-attaching filter

and flexible tubing.

4. Install new Particulate Filter and gently re-install flexible tubing.

5. Locate the Breather Filter (cylindrical tube) which is located at the top front of unit, as

viewed from the rear.

6. Carefully maneuver the filter from its current position outward so that the flexible tubing can

be removed without interference.

PD0020500A

7. Disconnect one end of the Breather Filter using the plastic twist-lock Luer fitting. Gently

remove the fitting and attached tubing from the filter.

8. Using a ¼” open-end wrench, carefully remove the plastic fitting from the filter and set aside.

Do not lose this fitting, as it will be used to install the new filter.

9. Place a ¼” wrench on the fitting located o the opposite side of Breather Filter. Carefully

rotate filter until it disconnects from fitting.

10. Remove protective foil caps from new BreatherFilterand carefullyinstall it by reversingsteps

9, 8, 7 and 6.

11. Secure the rear panel.

12. Install the TransformerIn-line Filterin accordance withthe instructions included with the

Transformer In-Line Filter Kit, PD0017000

Table des matières

Autres manuels Arbiter Systems Instrument de mesure

Arbiter Systems

Arbiter Systems 940A Manuel utilisateur

Arbiter Systems

Arbiter Systems Portable Power Sentinel 933A Manuel utilisateur

Arbiter Systems

Arbiter Systems 931A Manuel utilisateur

Arbiter Systems

Arbiter Systems 1092A Manuel utilisateur

Arbiter Systems

Arbiter Systems 1133A Manuel utilisateur

Arbiter Systems

Arbiter Systems 1040C Guide d'installation

Arbiter Systems

Arbiter Systems 940A Manuel utilisateur

Arbiter Systems

Arbiter Systems 931A Instructions d'installation et d'utilisation

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur