Araknis AN-620-SW Manuel utilisateur

AN-620-SW

Araknis 620 Switch Quick Start Guide

Welcome to Araknis Networks™

Thank you for choosing an Araknis 620 series managed switch. With multi-gigabit

connectivity on all ports, updated modern aesthetics, and a managed interface, the

Araknis 620 series switch is a sleek and highly capable addition to any network.

Series overview

Model Ethernet

Ports SFP+Ports

PoE

Budget

(Watts)

AN-620-SW-R-8-POE 8 2 240

AN-620-SW-R-24-POE 24 2 720

Unboxing

The package contains:

Switch Rubber feet for flat

surfaces (4)

Rack-mount kit:

ears (2), screws

(8)

Quick Start Guide

QRcard

AC power cord

Installing the switch

Rack mount Shelf mount

Caution: -.To avoid possible interference or damage, do not stack equipment on top

of the switch.

Rack mounting guidelines

lThe maximum ambient temperature of the space the switch is installed in should

not exceed 122 °F/50 °C.

lAllow to air flow through the rack.

lVerify all the leveling feet or casters are adjusted correctly and they come in

contact with the supporting surface. Always load heavier equipment at the

bottom of the rack.

lMake sure the rack is grounded and the equipment is surge protected.

lDo not overload the power equipment, or the switch. Check out our WattBox Best

Practices for more information.

Step 3: Connections

SFP+ ports

The SFP+ (Small Form Factor Pluggable plus) ports support up to 10 Gbps connection

and are typically used to connect switches together. Use SFP+ adapters for RJ45 or

multi-mode fiber cables (sold separately).

PoE budgeting

The PoE budget (Power over Ethernet) limits the amount of power available to all ports,

with a maximum of 60W on an individual port. Add the total number of possible watts

that the connected devices can consume to make sure everything can receive power

reliably. See the example below.



Model PoE budget

(Watts)

AN-620-SW-R-8-

POE 240

AN-620-SW-R-

24-POE 720

Total PoE budget available = 240

Total PoE device consumption = 47

Remaining PoE budget available = 193

LED states &reset procedures

Front

LED LED state Description

Power



On The switch is powered on.

Off The switch is powered off.

Speed/PoE



On The port is passing 2.5Gbps and/or PoE.*

Off The port is not passing 2.5Gbps and/or PoE.*

Link/Act



On The port detects a connection.

Blinking Packets are flowing through the port.

Off The port does not detect a connection or the

port is disabled.

*Configurable in the web interface.

Rear

LED LED state Description

RJ45 2.5G



On The RJ45 port is negotiating packets at 2.5Gbps.

Off

The RJ45 port is not negotiating 2.5Gbps but may be

passing traffic. Check the Link/Act LED to verify if packets

are flowing through the port.

SFP 10G



On The SFP port is negotiating packets at 10Gbps.

Off

The SFP port is not negotiating 10Gbps but may be

passing traffic. Check the Link/Act LED to verify if packets

are flowing through the port.

Link/Act



Blinking Packets are flowing through the port.

Off The port does not detect a connection.



Reset procedures

The reset button is on the back of the

switch.

Note: -__.The front and back power LEDs have the same behavior.

Reset button action LEDstate Description

Hold the reset button for 1-9

seconds Blinking slowly Restarts the switch

Hold the reset button for 10-

19 seconds

Blinking

moderately

Resets the username and

password to araknis.

Hold the reset button for

more than 20 seconds Blinking rapidly Resets the switch to factory

defaults.

Step 5: Configuration

Araknis switches can be configured through OvrC or the local interface. The local

interface is accessible using OvrC’s webconnect feature, typing the switch’s DHCP

address into your browser’s address bar, or using the switch’s default IP address.

Configuring the switch in OvrC

OvrC provides remote device management, real-time notifications, and intuitive

customer management, using your computer or mobile device. Setup is plug-and-play,

with no port forwarding or DDNS address required.

To add this device to your OvrC account:

1. Connect the switch to the internet.

2. Log into OvrC (www.ovrc.com).

3. Scan the site using an OvrC Pro

device, or add the switch manually

by entering the MAC address and

Service Tag.

Logging into the web interface

1. Log into the switch using the default

credentials:

Username araknis

Password araknis

2. You must update the password after

initial login.

Table des matières

Autres manuels araknis Changer

araknis

araknis AN-110-SW-C-5P Manuel utilisateur

araknis

araknis 300 - SERIES Manuel utilisateur

araknis

araknis 310 Series Manuel utilisateur

araknis

araknis AN-300-SW-F/R-8 Manuel utilisateur

araknis

araknis AN-210-SW-R-8-POE Manuel utilisateur

araknis

araknis 210 Series Manuel utilisateur

araknis

araknis AN-100-SW-R-5 Manuel utilisateur

araknis

araknis AN-100-SW-R-5 Manuel utilisateur

araknis

araknis AN-210-SW-F/R-8-POE Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

araknis AN-620-SW Manuel utilisateur

Manuels Changer populaires d'autres marques