aquaBUBBLER AB12 Manuel utilisateur
Concrete
Pad
Ground
Work Timber
Floor
WASTE
W A TER
WASTE
W A TER
Identify Water & Drainage Points
Determine Installation Surface
Outdoor Indoor
Where installed in
frost-prone areas, unit
must be fitted with an
Anti-Freeze Valve.
Warranty will otherwise
be void.
Anti-Freeze Valve
1. Timber boxing foundation
2. Screws and washers
3. Bag of cement
4. Socket Extension Bar
5. 10mm threaded rod and nuts
6. Flexible head ratchet wrench
7. 43 mm hole saw
8. 15 mm hole saw
9. 10 mm socket
Plumbing Tools
Unit must be installed by a
CERTIFIED PLUMBER.
Failure to do so will void all warranties.
Decide Orientation
WALLWALL
WALKWAY
CORNER
If near a wall, locate Keyhole
OUTSIDE zone of inaccessibility
(marked as BLACK in illustration
below)
Assign Inlet / Outlet Location
WALL
Front
Pod
Is an Anti-Freeze
Valve Required?
1.
2.
3.
4.
5.
6.
7. 8. 9.
Keyhole
3
2
4
67
5
PRE - INSTALLATION
Classic / Universal / Universal 2 aquaBUBBLER
Locate Water Inlet & Waste Water
Outlet at back of unit (out of view),
or at either side if necessary.
PLease read Pre-installation at back page
ATTENTION: See next page for INSTALL GUIDE
au: 1300 213 7 74 nz: 0800 213 774 www.aquabubbler.com
Maximum Water Pressure: 1600 kPa
Maximum Temperature: 65°C
Installation must be in accordance with
AS/NZS 3500.1 & AS/NZS 3500.2
Location
1
Code: AB12 / ABUA13 / AB2UA14
Do not place Water
Inlet & Waste Water
Outlet under the Side
Pod: this will obstruct
wheelchair access.
[ Universal only ]
Water
Supply
Eliminate
particulate matter
(copper & brass
filings) before
connecting
to unit.
Water
Inlet
We recommended to
Installing Isolation Valve
on Water Inlet (not
supplied) externally for
easy maintenance.
DON’T Install S-Trap
below the pod !!
S -TrapIsolation Valve
Pod has its own
in-built S-Trap
Flush out the lines
3
2
4
DON’T FORGET
Seal all plumbing
Apply sealant to
T-junction pipe
ends before
inserting them
into other pipes
Check for leaks
Run taps and
adjust any
insecure
connections
SET UP FOR USE
Run the tap
Adjust water pressure
Rotate keyhole with a
5mm screwdriver to
adjust water pressure
until the pod is full
Advise client to check
water pressure 48 hours
aer installation, as it may
require re-adjustment
Leave T15 Post Torx
Security Screwdriver
with client
678
*Indicates correct gauges for anchor
system types listed; choice of anchor
system is at installer's discretion
Front of unit
BMP
will end up here
(between two holes)
Place Base Mounting Plate (BMP) halves
in position on the installation surface.
Position the BMP so that the Front of the
unit will be in the middle of 2 holes.
Mark anchor points on the surface
through BMP holes and drill out.
Fit o either 12mm threaded rods or
16mm dynabolts*
Remove PVC S-Trap inside to gain access
to the base of the unit.
Place unit over anchors, then place BMP
halves back inside unit over anchors and
secure in place.
PLease read Pre-installation at back page
ATTENTION: See next page for PRE-INSTALL GUIDE
au: 1300 213 7 74 nz: 0800 213 774 www.aquabubbler.com
5
Locate Internal Base Mounting Plates
Classic / Universal / Universal 2 aquaBUBBLER INSTALLATION
Mark
measurements
& dimensions
as indicated by
Schematic on
https://aquabubbler.com
1
Consult Schematic
Schematic
Download
Attach Side Pod
Connect pipe to tap fitting
Connect Black Director from Pod
to the Waste Pipe
Screw Side Pod to body with
a 5mm Allen Key (not supplied)
1
2
3
1
2
1
2
3
3
[ Universal only ]
Code: AB12 / ABUA13 / AB2UA14
Ce manuel convient aux modèles suivants
2
Autres manuels aquaBUBBLER Système d'eau
Manuels Système d'eau populaires d'autres marques
Spirotech
Spirotech SPIROVENT SUPERIOR S250 Manuel utilisateur
Culligan
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manuel utilisateur
A.O. Smith
A.O. Smith Dura-Max AJH - 1000A - P Manuel utilisateur
Microline
Microline T.F.C.-4 Manuel
Eureka Forbes
Eureka Forbes Aquaguard Select Manuel utilisateur
Cetetherm
Cetetherm AquaEfficiency Manuel utilisateur
