Aprimatic Over Manuel
INSTALLATION AND MAINTENANCE MANUAL
FOR SWING DOOR
Over – Over Evo – Over Heavy
2 www.Aprimatic.it
1. INTRODUCTION
Before you begin to install or start an automatic pedestrian doors, an inspection must be carried out on site by qualified
personnel, for making measurements of the compartment wall, door and drive.
This inspection is to assess the risk and to select and implement the most appropriate solutions according to the type of
pedestrian traffic (intense, narrow, one‐way, bi‐directional, etc..), The type of users (elderly, disabled, children, etc..), in the
presence of potential hazards or local circumstances.
To assist installers in applying the requirements of European Standard EN 16005 concerning the safe use of automatic
pedestrian doors, we recommend consulting the guides E.D.S.F. (European Door and Shutter Federation) available on
www.edsf.com.
1.1 GENERAL SAFETY INSTRUCTION
This installation manual is intended for professionally competent personnel only. Before installing the product, carefully read
the instructions.
Bad installation could be hazardous. The packaging materials (plastic, polystyrene, etc.) should not be discarded in the
environment or left within reach of children, as these are a potential source of hazard.
Before installing the product, make sure it is in perfect condition. Do not install the product in an explosive environment and
atmosphere: gas or inflammable fumes are a serious hazard risk.
Before installing the automations, make all structural changes relating to safety clearances and protection or segregation of
all areas where there is risk of being crushed, cut or dragged, and danger areas in general.
Make sure the existing structure is up to standard in terms of strength and stability. Aprimatic srl is not responsible for failure
to use Good Working Methods in building the frames to be motorised or for any deformation occurring during use.
The safety devices (safety sensor, photocells, etc.) must be installed taking into account: applicable laws and directives, Good
Working Methods, installation premises, system operating logic and the forces developed by the motorised door.
Apply hazard area notices required by applicable regulations.
Each installation must clearly show the identification details of the automatic pedestrian door.
1.2 EC MARKING AND EUROPEAN DIRECTIVES
Aprimatic automations for swing pedestrian door, are designed and manufactured in compliance with the
safety requirements of the European standard EN 16005 and are CE‐marked in accordance with the
following European Directives:
Low Voltage Directive (2006/95/EC) and the Electromagnetic Compatibility Directive (2004/108/EC).
The automation APRIMATIC also include a Declaration of Incorporation according to the Machinery Directive (2006/42/EC).
Pursuant to Machinery Directive (2006/42/CE) the installer who motorises a door or gate has the same obligations as the
manufacturer of machinery and as such must:
‐prepare the technical file which must contain the documents indicated in Annex V of the Machinery Directive; (The
technical file must be kept and placed at the disposal of competent national authorities for at least ten years from the date of
manufacture of the pedestrian door);
‐draft the EC declaration of conformity in accordance with Annex ll‐A of the Machinery Directive and deliver it to the
customer;
‐affix the CE marking on the power operated door in accordance with point 1.7.3 of Annex l of the Machinery
All data and information contained in this manual have been drawn up and checked with the greatest care. However
APRIMATIC . cannot take any responsibility for eventual errors, omissions or inaccuracies due to technical or illustrative
purposes.
APRIMATIC reserves the right to make changes and improvements to their products. For this reason, the illustrations and the
information appearing in this document are not definitive.
This edition of the manual cancels and replaces all previous versions. In case of modification will be issued a new edition.
3 www.Aprimatic.it
2. TECHNICAL DATA
OVER OVER EVO OVER HEAVY
Automation type: LIGHT
(for internal use, not exposed to wind
pressure)
Automation type: SPRING
(with closing spring) Automation type: HEAVY
Dimensions: 82 x 117 x 443 mm
(Height x Depth x Length)
Dimensions: 135 x 118 x 503 mm
(Height x Depth x Length)
Dimensions: 104 x 118 x 463 mm
(Height x Depth x Length)
200 kg x 0,8 m
220 kg x 0,8 m
300 kg x 0,8 m
Opening and closing time: 2 – 6 s Opening and closing time: 2 – 6 s Opening and closing time: 2 – 6 s
Duty class:
Continuous operation
Intermittent operation: S3 = 100%
Duty class:
Continuous operation
Intermittent operation: S3 = 100%
Duty class:
Continuous operation
Intermittent operation: S3 = 100%
Power supply: 100–240 Vca 50/60 Hz
Rated power: 40 W
Stand‐by: 8 W
Power supply: 100–240 Vca 50/60 Hz
Rated power: 70 W
Stand‐by: 8 W
Power supply: 100–240 Vca 50/60 Hz
Rated power: 70 W
Stand‐by: 8 W
Rated load: 20 Nm Rated load: 23 Nm Rated load: 40 Nm
Protection rating: IP 20 Protection rating: IP 20 Protection rating: IP 20
Operating temperature:
‐15 °C +50 °C
Operating temperature:
‐15 °C +50 °C
Operating temperature:
‐15 °C +50 °C
Parameter Settings:
Buttons and Display
Parameter Settings:
Buttons and Display
Parameter Settings:
Buttons and Display
Connections to control and safety
devices:
Dedicated connecting terminals
Connections to control and safety
devices:
Dedicated connecting terminals
Connections to control and safety
devices:
Dedicated connecting terminals
Power output for accessories:
12 Vdc (1 A max)
Power output for accessories:
12 Vdc (1 A max)
Power output for accessories:
12 Vdc (1 A max)
Memory for settings and saving:
Micro SD standard
Memory for settings and saving:
Micro SD standard
Memory for settings and saving:
Micro SD standard
PC connection: Micro USB standard PC connection: Micro USB standard PC connection: Micro USB standard
Function selector device with
transponder key: FSD1
Function selector device with
transponder key: FSD1
Function selector device with
transponder key: FSD1
Battery power device for emergency
opening: OVER
Battery power device for emergency
opening: OVER HEAVY
Battery power device for emergency
opening: OVER HEAVY
Signal of door position ‐Signal of door position
N.B. The technical data above refer to average conditions of use and cannot be certain in each case. Each automatic entrance
variables such as: friction, balancing and environmental conditions that may substantially change both the duration and the
quality of the operation of the automatic or some of its components, including the automation. The installer must to adopt
adequate safety coefficients for each particular installation.
4 www.Aprimatic.it
3. STANDARD INSTALLATION
Rif. Code Description
1
42605/001
42605/003
42605/002
OVER automation (Light) for swing doors
OVER EVO automation (Spring) for swing doors
OVER HEAVY automation (Heavy) for swing doors
2 42605/051 Sliding arm
3 SD3 Infrared safety sensor
4 OS1 Unidirectional microwave opening sensor
5 42605/060 Electronic function selector with transponder key
‐42605/070
42605/071
Battery power device for OVER automation
Battery power device for OVER EVO and OVER HEAVY automation
Note: Components and codes are those most commonly used in systems for automatic swing doors. The full range of
equipment and accessories is also available in the sales list.
The given operating and performance features can only be guaranteed with use of APRIMATIC accessories and safety
devices.
1
5
2 4
3
5 www.Aprimatic.it
4. ASSEMBLY PROCEDURE OF THE AUTOMATION
Check the stability, the weight of the leaf and that the movement is smooth and without friction (if necessary to reinforce the
frame). Any closing door device must be removed or completely deactivated.
Check the correct operation in case of installation on doors that divide environments at different pressures.
4.1 INSTALLATION OF OVER AUTOMATION WITH SWSA SLIDING ARM
Use the sliding arm to pull with doors which open inside (view from the automation).
Remove the cover and fix the automation in a stable and leveled way to the wall using the measurements shown in the
figure; refer to the axis of the door hinges.
Fix the sliding arm on the door as shown in the figure. Insert the sliding arm in the guide and fix to the automation.
Note: if necessary, you can change the measure H, between the automation and the door, by replacing the spacer, using the
codes listed in the table.
(H) OVER automation
28 Sliding arm + Spacer 17mm
45 Sliding arm
62 Sliding arm + Spacer 51mm
Move the door manually, and verify the correct opening and closing smoothly.
Adjust the opening mechanical stop inside the sliding arm.
CLOSING OF THE AUTOMATION COVER
Insert the cover profile to the base profile and attach it to the heads. To prevent the cover from being opened without the
use of a tool, you can remove the pins inserted into the cover, and secure the cover to the heads at the holes, using the
screws 2,9 x9,5 not supplied by us.
6 www.Aprimatic.it
4.2 INSTALLATION OF OVER AUTOMATION WITH ARTICULATED ARM
Use the articulated arm to push with doors which open outside (view from the automation).
Remove the cover and fix the automation in a stable and leveled way to the wall using the measurements shown in the
figure; refer to the axis of the door hinges.
Fix the bracket of the articulated arm on the door, using the measurements shown in the figure.
Note: if necessary, you can change the measure H, between the automation and the door, by replacing the spacer, using the
codes listed in the table.
(H) OVER automation
28 Articulated arm+ spacer H17
45 Articulated arm
62 Articulated arm + spacer H51
Fix the articulated arm to the automation, and fix the other end of the articulated arm to the door.
Move the door in the closed position, and adjust the length of the half‐arm [A] so that the angle between the two half‐arms
[A] and [B] is the greater possible.
(*) To increase the opening force it is possible to reduce the angle and reduce the measurement of fixing of the articulated
arm, as shown in figure.
Move the door manually, and verify the correct opening and closing smoothly.
Install the opening mechanical stop (not supplied by us).
Note: the mechanical stop on the floor must be fixed in a visible position and must not create tripping hazard.
CLOSING OF THE AUTOMATION COVER
Insert the cover profile to the base profile and attach it to the heads. To prevent the cover from being opened without the
use of a tool, you can remove the pins inserted into the cover, and secure the cover to the heads at the holes, using the
screws 2,9 x9,5 not supplied by us.
7 www.Aprimatic.it
4.3 INSTALLATION OF OVER EVO AUTOMATION WITH SLIDING ARM
Use the sliding arm to pull with doors which open inside (view from the automation).
If the door has the hinge on the right, disassemble the gear motor group from the automation and move the spring group
from the left side to the right side of the automation, as shown in the figure.
Factory setting Hinge on the right
8 www.Aprimatic.it
Remove the cover and fix the automation in a stable and leveled way to the wall using the measurements shown in the
figure; refer to the axis of the door hinges.
Fix the sliding arm on the door as shown in the figure. Insert the sliding arm in the guide and fix to the automation (use the
screw M8 x 50)
Note: if necessary, you can change the measure H, between the automation and the door, by replacing the spacer, using the
codes listed in the table.
(H) OVER EVO automation
30 Sliding arm + spacer H17
47 Sliding arm
64 Sliding arm + spacer H51
PRE‐CHARGING OF THE CLOSING SPRINGS
Tighten the screw [a] and compress the springs of about X = 10 mm, as shown in the figure.
Move the door manually, and verify the correct opening and closing force.
Adjust the opening mechanical stop inside the sliding arm.
CLOSING OF THE AUTOMATION COVER
Attach the cover profile to the base profile. To prevent the cover from being opened without the use of a tool, you can
secure the cover to the heads at the holes, using the screws 2,9 x9,5 not supplied by us.
9 www.Aprimatic.it
4.4 INSTALLATION OF OVER EVO AUTOMATION WITH ARTICULATED ARM
Use the articulated arm to push with doors which open outside (view from the automation).
If the door has the hinge on the left, disassemble the gear motor group from the automation and move the spring group
from the left side to the right side of the automation, as described in chapter 4.5.
Hinge on the left Factory setting
Remove the cover and fix the automation in a stable and leveled way to the wall using the measurements shown in the
figure; refer to the axis of the door hinges.
Fix the bracket of the articulated arm on the door, using the measurements shown in the figure.
Note: if necessary, you can change the measure H, between the automation and the door, by replacing the spacer, using the
codes listed in the table.
(H) OVER EVO automation
30 Articulated arm + spacer H17
47 Articulated arm
64 Articulated arm + spacer H51
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels Aprimatic Système d'ouverture de porte
