Apricorn Aegis Bio 3.0 Manuel utilisateur

User’s Manual

Aegis Bio 3.0

Windows is a registered trademark of Microsoft Corporation.

All other trademarks and copyrights referred to are the property of their

respective owners.

Distribution of modied versions of this document is prohibited without

the explicit permission of the copyright holder.

Distribution of the work or derivative work in any standard (paper) book

form for commercial purposes is prohibited unless prior permission is

obtained from the copyright holder.

DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR

IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,

INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,

ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH

DISCLAIMERS ARE HELD TO BE LEGALLY INVALID

Contents

About the Aegis Bio 4

Package contents 4

Fingerprint Sensor 5

Swiping your Finger 5

Basic LED States 5

Aegis Bio - Connections 6

Before you begin 6

Connecting the Aegis Bio 6

Connecting the Aegis Bio with USB Y-Cable 7

Getting Started - Out of the Box 8

Unlocking the Aegis Bio 9

Locking the Aegis Bio 9

Complete Re-set 9

Formatting the Aegis Bio After a Complete Re-set 10

Formatting for Windows 10

Formatting for Mac 11

Enrolling a new nger 12

Hibernating, Suspending or Logging off from the OS 13

Troubleshooting 14

Technical Support 15

Warranty and RMA information 15

About the Aegis Bio

Package contents

When security matters, trust your

data to the Aegis Bio.

Designed for those that demand the

highest level of protection for their

data, the Aegis Bio fuses leading

edge technology in biometric

authentication and encryption with a

rugged, portable design to produce

a truly remarkable drive.

Quick Start Guide

Basic LED States

LOCK RED LED

UNLOCK GREEN LED

ADMIN BLUE LED

4ENROLL Button

Solid RED = Standby, swipe nger to unlock

Flashing RED = Error

Solid BLUE / Flashing GREEN = Ready to enroll ngerprint

Solid GREEN = Drive unlocked

Flashing GREEN = Disk activity

Aegis Bio 3.0

Swiping your Finger

To successfully swipe your nger,

start your swipe by placing your

ngertip on the downward facing

arrow at the top of the biometric

sensor. Swipe your nger in a

downward motion across the

sensor. If your swipe is successful

the GREEN LED will start to icker.

Start

swipe

here

Aegis Bio with integrated USB 3.0 cable

Padded Travel Pouch

Auxiliary Y-USB Extension cable

Quick Start Guide

Fingerprint Sensor

Basic LED States

LOCK RED LED

UNLOCK GREEN LED

ADMIN BLUE LED

4ENROLL Button

Solid RED = Standby, swipe nger to unlock

Flashing RED = Error

Solid BLUE / Flashing GREEN = Ready to enroll ngerprint

Solid GREEN = Drive unlocked

Flashing GREEN = Disk activity

Swiping your Finger

To successfully swipe your nger,

start your swipe by placing your

ngertip on the downward facing

arrow at the top of the biometric

sensor. Swipe your nger in a

downward motion across the

sensor. If your swipe is successful

the GREEN LED will start to icker.

Start

swipe

here

Aegis Bio - Connections

Before you begin

Be sure to review the following information before you begin to use the

Aegis Bio.

Attention: Use only the included cables with your Aegis Bio. You

might damage the drive if you use a cable not included with the

Aegis Bio.

The Aegis Bio is designed for portable use without an AC power adapter

and in most cases will be able to power on a single USB port. In the event

that the Aegis Bio is unable to power on a single USB connection, use the

included USB Y-cable.

Connecting the Aegis Bio

1. Attach the integrated USB cable of theAegis Bio drive to an available USB

port on your computer, as shown below.

2. At least one of theAegis Bio LEDs should turn on, indicating that theAegis

Bio is receiving power.

If none of the LEDs

turns on, use the

included USB Y-cable.

Refer to directions on the

following page

Connecting the Aegis Bio with USB Y-Cable

If none of the Aegis Bio LEDs power on a single USB connection, use the

included USB Y-cable.

1. Attach theAegis Bio’s integrated USB cable to the female connector of

the USB Y-cable.

2. Connect the two male USB connectors to two available

USB ports on your computer.

3. At least one of theAegis Bio LEDs should turn on, indicating that the

Aegis Bio is powered.

Getting Started - Out of the Box

1. Attach the integrated USB cable of

theAegis Bio to an available USB

port on your computer. TheAegis

Bio LEDs will show Solid BLUE and

Flashing GREEN indicating that the

drive is ready to enroll your ngerprint.

2. Swipe your Finger. The BLUE LED

will turn off while the GREEN LED

starts to icker briey as the Aegis Bio

processes your ngerprint.

Wait until the BLUE LED turns back

to Solid BLUE and the GREEN LED

returns to its ashing state.

3. Continue to repeat Step 2 until both

the BLUE and GREEN LED are

in a solid state, indicating that your

ngerprint is fully enrolled.

NOTE: The number of attempts will vary depending on the quality of

the ngerprint read. For most people six swipes will be sufcient.

If there is a problem with a ngerprint read, the BLUE LED will turn off and

the RED LED with start to ash.

4. To enroll more ngerprints, press the ENROLL button within 15

seconds from your last successful ngerprint enrollment and repeat

the process in steps 2 and 3.

NOTE: A maximum of 5 ngerprints can be stored. There is a 15 second

timeout between entering ngerprints. If the ENROLL button is not pressed

again after the last ngerprint, the unit will assume no more ngerprints will

be entered and return to a standby state.

Once 5 ngerprints have been stored, all three LEDs will turn on. After 2

seconds the GREEN and BLUE LED will turn off with just the Solid RED

LED showing. At this point no more ngerprints can be enrolled.

NOTE: Once enrolled, ngerprints cannot be un-enrolled

individually. To remove enrolled ngerprints, a complete re-set

of the drive is required.

TIP: We highly recommend that you enroll at least three

different ngers to ensure access to the drive in the case

that your primary nger cannot be used.

Unlocking the Aegis Bio

Locking the Aegis Bio

Complete Re-set

To lock the Aegis Bio after it has been unlocked, use the directions below.

1. Press the ENROLL button until the RED LED turns on. The drive

will check for disk activity. If no data has been written to the drive for 2

seconds, the drive will lock. If data is being written to the drive, it will wait

until the disk activity has been nished before locking the drive.

2. TheAegis Bio LED will go from GREEN to Solid RED when locked.

NOTE: If you use the safely remove hardware button (Windows) or

Eject device (Mac), theAegis Bio will lock and dismount but the LED

will remain GREEN. You will need to physically remove and re-plug the

USB cable before being able to access the drive.

Once your ngerprints are enrolled, you can unlock the Aegis Bio using the

directions below.

1. Attach the integrated USB cable of theAegis Bio to an available

USB port on your computer. TheAegis Bio LED will show Solid RED

indicating that the drive is locked and is in Standby mode.

2. Swipe your Finger. The RED LED will turn off while the GREEN LED will

start to icker briey as the Aegis Bio processes your ngerprint.

3. You will know that your ngerprint has been accepted once the GREEN

LED stops ickering and turns Solid GREEN. The drive is now

unlocked and ready for use.

NOTE: The complete re-set will delete all stored ngerprints and will

change the encryption key used to secure the drive.

THIS WILL ERASEANY DATA ON THE DRIVE. USE WITH CAUTION.

1. Hold down the ENROLL button and plug theAegis Bio USB cable into

your computer. The LED will alternate RED / BLUE.

2. Release the ENROLL button, then within 5 seconds repress and hold the

ENROLL button for 15 seconds. The LED will alternate between RED /

BLUE / GREEN during the 15 seconds.

3. When the drive successfully re-sets, the GREEN LED will stay on for 3

seconds, then will change to Solid BLUE with the GREEN LED ashing.

You can now release the ENROLL button.

4. The Aegis Bio has now been returned to its OUT OF THE BOX state

and is now ready to enroll ngerprints. Once ngerprints are enrolled

the Aegis Bio will need to be partitioned and reformatted before use.

Formatting the Aegis Bio After a

Complete Re-set

After a complete re-set, follow the instructions on page 8 “Getting

Started” to enroll your ngerprints. Once your ngerprints are enrolled

follow the directions below to format and partition your Aegis Bio.

Formatting for Windows

1. Right-click My Computer, and then click Manage from the Windows

desktop.

2. In the Computer Manage window, click Disk Management. In

the Disk Management window, the Aegis Bio is recognized as an

unknown device that is uninitialized and unallocated.

3. Do the following to make the drive recognized as a basic drive.

• If the Initialize and Convert Disk Wizard window opens, click

Cancel, then initialize the disk manually using the following

steps.

a. Right-click Unknown Disk, and then select Initialize Disk.

b. In the Initialize Disk window, click OK.

4. Right-click in the blank area under the Unallocated section, and

then select New Partition. The Welcome to the New Partition Wizard

window opens.

5. Click Next.

6. Select Primary partition and click Next.

7. If you need only one partition, accept the default partition size and

click Next.

8. Click Next.

9. Create a volume label, select Perform a quick format, and then click

Next.

10. Click Finish.

11. Wait until the format process is complete. The Aegis Bio will be

recognized and it is available for use.

Autres manuels pour Aegis Bio 3.0

Table des matières

Autres manuels Apricorn Stockage

Apricorn

Apricorn Aegis Secure Key Manuel utilisateur

Apricorn

Apricorn Xtreme Upgrade Manuel utilisateur

Apricorn

Apricorn ADVRX 500GB Manuel utilisateur

Apricorn

Apricorn Aegis Padlock A25-PL256 128GB Manuel utilisateur

Apricorn

Apricorn ADT 500GB Manuel utilisateur

Apricorn

Apricorn Aegis Padlock A25-PL128 250GB Manuel utilisateur

Apricorn

Apricorn AMKF-1 Manuel utilisateur

Apricorn

Apricorn EZ-BUS-DTS 1TB Manuel utilisateur

Apricorn

Apricorn Aegis Padlock Fortress Manuel utilisateur

Apricorn

Apricorn Aegis Mini A18-USB 100GB Manuel utilisateur

Apricorn

Apricorn Aegis Padlock Fortress Manuel du propriétaire

Apricorn

Apricorn Aegis Padlock SSD Manuel utilisateur

Apricorn

Apricorn Aegis Mini A18-FW 120GB Manuel utilisateur

Apricorn

Apricorn Aegis NetDock Manuel utilisateur

Apricorn

Apricorn EZ-BUS-DTC 250GB Manuel utilisateur

Apricorn

Apricorn ASK-256-4GB Manuel utilisateur

Apricorn

Apricorn Aegis Secure Key 3z Manuel utilisateur

Apricorn

Apricorn USB Storage Device Manuel utilisateur

Apricorn

Apricorn Aegis Padlock A25-PLE256 500GB Manuel utilisateur

Apricorn

Apricorn Aegis Padlock DT Manuel utilisateur

Apricorn

Apricorn EZ Storage Manuel utilisateur

Apricorn

Apricorn Aegis Padlock Manuel utilisateur

Apricorn

Apricorn Aegis Padlock DT Manuel utilisateur

Apricorn

Apricorn Aegis Padlock A25-PLE256S 128GB Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur