Apogee SU-100 Manuel utilisateur

APOGEE INSTRUMENTS, INC. | 721 WEST 1800 NORTH, LOGAN, UTAH 84321, USA

TEL: (435) 792-4700 | FAX: (435) 787-8268 | WEB: APOGEEINSTRUMENTS.COM

OWNER’S MANUAL

ULTRAVIOLET SENSOR

Model SU-100

(including SS model)

TABLE OF CONTENTS

Owner’s Manual ................................................................................................................................................................................................................ 1

Certificate of Compliance .................................................................................................................................................................................... 3

Introduction ............................................................................................................................................................................................................. 4

Sensor Models ......................................................................................................................................................................................................... 5

Specifications........................................................................................................................................................................................................... 6

Deployment and Installation.............................................................................................................................................................................. 7

Operation and Measurement............................................................................................................................................................................. 9

Maintenance and Recalibration.......................................................................................................................................................................12

Troubleshooting and Customer Support......................................................................................................................................................14

Return and Warranty Policy ..............................................................................................................................................................................15

CERTIFICATE OF COMPLIANCE

EU Declaration of Conformity

This declaration of conformity is issued under the sole responsibility of the manufacturer:

Apogee Instruments, Inc.

721 W 1800 N

Logan, Utah 84321

USA

for the following product(s):

Models: SU-100

Type: Ultraviolet Sensor

The object of the declaration described above is in conformity with the relevant Union harmonization legislation:

2014/30/EU Electromagnetic Compatibility (EMC) Directive

2011/65/EU Restriction of Hazardous Substances (RoHS 2) Directive

Standards referenced during compliance assessment:

EN 61326-1:2013 Electrical equipment for measurement, control and laboratory use – EMC requirements

EN 50581:2012 Technical documentation for the assessment of electrical and electronic products with respect to the

restriction of hazardous substances

Please be advised that based on the information available to us from our raw material suppliers, the products manufactured

by us do not contain, as intentional additives, any of the restricted materials including cadmium, hexavalent chromium, lead,

mercury, polybrominated biphenyls (PBB), polybrominated diphenyls (PBDE).

Further note that Apogee Instruments does not specifically run any analysis on our raw materials or end products for the

presence of these substances, but rely on the information provided to us by our material suppliers.

Signed for and on behalf of:

Apogee Instruments, May 2016

Bruce Bugbee

President

Apogee Instruments, Inc.

INTRODUCTION

Ultraviolet (UV) radiation constitutes a portion of the electromagnetic spectrum from 100 to 400 nm, and is further

subdivided into three wavelength ranges: UV-A (315 to 400 nm), UV-B (280 to 315 nm) and UV-C (100 to 280 nm). Much of the

UV-B and all of the UV-C wavelengths from the sun are absorbed by the Earth’s atmosphere. There are also many artificial UV

light sources available that output a select wavelength range or offer a broadband UV radiation source.

Most UV sensors designed for sunlight measurements are sensitive to UV radiation in the UV-A and UV-B ranges. Apogee

Instruments SU-100 UV sensors detect UV radiation from 250 to 400 nm and are calibrated in photon flux units of micromoles

per square meter per second (µmol m-2 s-1). The output can also be expressed in energy flux units of watts per square meter

(W m-2, equal to Joules per second per square meter).

Typical applications of UV sensors include incoming UV radiation measurement in outdoor environments (not recommended

for continuous outdoor deployment) or in laboratory use with artificial light sources (e.g., germicidal lamps).

Apogee Instruments SU-100 UV sensors consist of a photodiode and signal processing circuitry mounted in an anodized

aluminum housing, and a cable to connect the sensor to a measurement device. Sensors are potted solid with no internal air

space, and are designed for UV radiation measurement in indoor or outdoor environments. The SU-100 outputs an analog

voltage that is directly proportional to UV radiation incident on a planar surface (does not have to be horizontal), where the

radiation emanates from all angles of a hemisphere.

Sensor model number and serial number are located near the

pigtail leads on the sensor cable. If you need the

manufacturing date of your sensor, please contact Apogee

Instruments with the serial number of your sensor.

SENSOR MODELS

The SU-100 UV sensor is the only stand-alone UV sensor offered by Apogee Instruments. Additional models are covered in

their respective manuals.

Model

Signal

SU-100 Self-powered

SU-420 USB

SPECIFICATIONS

Calibration Traceability

Apogee SU-100 UV sensors are calibrated through side-by-side comparison to the mean of four Apogee model SU-100

transfer standard UV sensors under high intensity discharge metal halide lamps. The transfer standard UV sensors are

calibrated through side-by-side comparison to an Apogee model PS-200 spectroradiometer under sunlight (clear sky

conditions) in Logan, Utah. The PS-200 is calibrated with a LI-COR model 1800-02 Optical Radiation Calibrator using a 200 W

quartz halogen lamp. The 1800-02 and quartz halogen lamp are traceable to the National Institute of Standards and

Technology (NIST).

Spectral Response

SU-100

Sensitivity 0.20 mV per µmol m-2 s-1; 0.61 mV per W m-2

Calibration Factor

(reciprocal of sensitivity)

5.0 µmol m-2 s-1 per mV; 1.65 W m-2 per mV

Calibration Uncertainty ± 10 % (see Calibration Traceability below)

Measurement Repeatability less than 1 %

Non-stability

(Long-term Drift)

less than 3 % per year

Non-linearity less than 1 % (up to 300 µmol m-2 s-1)

Response Time less than 1 ms

Field of View 180º

Spectral Range 250 nm to 400 nm (see Spectral Response below)

Directional (Cosine)

Response ± 10 % at 75º zenith angle

Temperature Response Approximately 0.1 % per C

Operating Environment -40 to 70 C; 0 to 100 % relative humidity

Dimension 24 mm diameter; 28 mm height

Mass 75 g (with 5 m of lead wire)

Cable

5 m of two conductor, shielded, twisted-pair wire; additional cable available in multiples of 5 m;

santoprene rubber jacket (high water resistance, high UV stability, flexibility in cold conditions); pigtail

lead wires

Spectral response estimate of Apogee SU-100

UV sensors. Spectral response measurements

were made at 10 nm increments across a

wavelength range of 200 to 450 nm in a

monochromator with an attached electric light

source. Measured spectral data were

normalized at 350 nm.

DEPLOYMENT AND INSTALLATION

Mount the sensor to a solid surface with the nylon mounting screw provided. To accurately measure PPFD incident on a

horizontal surface, the sensor must be level. An Apogee Instruments model AL-100 Leveling Plate is recommended to level

the sensor when used on a flat surface or being mounted to surfaces such as wood. To facilitate mounting on a mast or pipe,

the Apogee Instruments model AL-120 Solar Mounting Bracket with Leveling Plate is recommended.

To minimize azimuth error, the sensor should be mounted with the cable pointing toward true north in the northern

hemisphere or true south in the southern hemisphere. Azimuth error is typically less than 1 %, but it is easy to minimize by

proper cable orientation.

In addition to orienting the cable to point toward the nearest pole, the sensor should also be mounted such that

obstructions (e.g., weather station tripod/tower or other instrumentation) do not shade the sensor. Once mounted, the

green cap should be removed from the sensor. The green cap can be used as a protective covering for the sensor when it

is not in use.

Nylon Screw: 10-32x3/8

Model AL-100

Nylon Screw: 10-32x3/8

Model AL-120

Cable Connectors

Apogee started offering in-line cable connectors on some

bare-lead sensors in March 2018 to simplify the process of

removing sensors from weather stations for calibration by

not requiring the full cable to be uninstalled back to the data

logger.

The ruggedized M8 connectors are rated IP67, made of

corrosion-resistant marine-grade stainless-steel, and

designed for extended use in harsh environmental

conditions.

Inline cable connectors are installed 30 cm from the head

(pyranometer pictured)

Instructions

Pins and Wiring Colors:All Apogee connectors have six

pins, but not all pins are used for every sensor. There may

also be unused wire colors inside the cable. To simplify data

logger connection, we remove the unused pigtail lead colors

at the data logger end of the cable.

If you ever need a replacement cable, please contact us

directly to ensure ordering the proper pigtail configuration.

Alignment: When reconnecting your sensor, arrows on the

connector jacket and an aligning notch ensure proper

orientation.

Disconnection for extended periods: When disconnecting

the sensor for an extended period of time from a station,

protect the remaining half of the connector still on the

station from water and dirt with electrical tape or other

method.

A reference notch inside the connector ensures

proper alignment before tightening.

When sending sensors in for calibration, only send the short

end of the cable and half the connector.

Tightening: Connectors are designed to be firmly finger-

tightened only. There is an o-ring inside the connector that

can be overly compressed if a wrench is used. Pay attention

to thread alignment to avoid cross-threading. When fully

tightened, 1-2 threads may still be visible.

Finger-tighten firmly

OPERATION AND MEASUREMENT

Connect the sensor to a measurement device (meter, datalogger, controller) capable of measuring and displaying or

recording a millivolt signal (an input measurement range of approximately 0-40 mV is required to cover the entire range of

UV from the sun). In order to maximize measurement resolution and signal-to-noise ratio, the input range of the

measurement device should closely match the output range of the UV sensor. DO NOT connect the sensor to a power

source. The sensor is self-powered and applying voltage will damage the sensor.

VERY IMPORTANT: Apogee changed all wiring colors of our bare-lead sensors in March 2018 in conjunction

with the release of inline cable connectors on some sensors. To ensure proper connection to your data device,

please note your serial number or if your sensor has a stainless-steel connector 30 cm from the sensor head then

use the appropriate wiring configuration below.

Wiring for SU-100 Serial Numbers range 0-2481

Wiring for SU-100 Serial Numbers 2482 and above or with a cable connector

Red: Positive (signal from sensor)

Black: Negative (signal from sensor)

Clear: Shield/Ground

Black: Negative (signal from sensor)

Clear: Shield/Ground

White: Positive (signal from sensor)

Sensor Calibration

The SU-100 has a standard UV calibration factor of exactly:

5.0 µmol m-2 s-1 per mV

Multiply this calibration factor by the measured mV signal to convert sensor output to UV in units of µmol m-2 s-1:

Calibration Factor (5.0 µmol m-2 s-1 per mV) * Sensor Output Signal (mV) = UV (µmol m-2 s-1)

5.0 * 35 = 175

UV-B Measurements and Spectral Errors

Apogee Instruments model SU-100 UV Sensors measure ultraviolet radiation between 250 and 400 nm in micromoles of

photons per square meter per second. Although the UV radiation between 280 and 315 nm (UV-B) is critically important in

photochemical and photobiological reactions, less than 3 % of the UV photons are in this range. Because only a small fraction

of the photons are in the UV-B range, the SU-100 cannot be used to selectively measure UV-B radiation. The SU-100 is

sensitive to UV-B radiation, but it is included with the UV-A radiation to provide a total measurement of UV radiation.

In addition to naturally occurring UV radiation from the sun, there are many electric light sources that emit UV radiation (e.g.,

cool white fluorescent, metal halide, mercury arc, and germicidal lamps). Although the relative wavelengths of UV radiation

differ among sunlight and electric lights, the error estimates shown in the table below indicate that the SU-100 provides

reasonable estimates of UV radiation coming from electric lamps (table provides spectral error estimates for UV radiation

measurements from radiation sources other than clear sky solar radiation). For common lamps, the error is less than 10 %.

The SU-100 is particularly useful for determining the UV filtering capacity of the transparent plastic and glass barriers that are

commonly used below electric lamps.

Example of UV measurement with an Apogee UV sensor. Full sunlight yields

UV radiation on a horizontal plane at the Earth’s surface of approximately

175 µmol m-2 s-1. This yields an output signal of 35 mV. The signal is

converted to UV radiation by multiplying by the calibration factor of 5.0

µmol m-2 s-1 per mV.

Full Sunlight

175 µmol m-2 s-1

Sensor Output

35 mV

Table des matières

Autres manuels Apogee Accessoires

Apogee

Apogee SQ-640 Manuel utilisateur

Apogee

Apogee Apogee Duet Manuel utilisateur

Apogee

Apogee SQX Series Manuel utilisateur

Apogee

Apogee SP-214 Manuel utilisateur

Apogee

Apogee ensemble Manuel utilisateur

Apogee

Apogee Apogee Duet Manuel utilisateur

Apogee

Apogee SU-221 Manuel utilisateur

Apogee

Apogee Apogee Duet Manuel utilisateur

Apogee

Apogee Symphony Mk II Manuel utilisateur

Apogee

Apogee SQX Series Manuel utilisateur

Apogee

Apogee Symphony Mobile Manuel utilisateur

Apogee

Apogee ensemble Manuel utilisateur

Apogee

Apogee ensemble Manuel utilisateur

Apogee

Apogee SQ-421X Manuel utilisateur

Apogee

Apogee SQ-618 Manuel utilisateur

Apogee

Apogee Quartet Manuel utilisateur

Apogee

Apogee SO-110 Manuel utilisateur

Apogee

Apogee Element 24 Manuel utilisateur

Apogee

Apogee SQ-212 Manuel utilisateur

Apogee

Apogee SQ-222 Manuel utilisateur

Apogee

Apogee symphony i/o mk II Manuel utilisateur

Apogee

Apogee ONE Manuel utilisateur

Apogee

Apogee ONE Manuel utilisateur

Apogee

Apogee Symphony I/O Mode d’emploi

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur