APG Architect Manuel utilisateur
Architect™Assembly Instructions for Topper and Tech Mounts
For use with apg®Minota®Cash Drawer
Architect™Topper
Hardware by SpacePole®/
Ergonomic®Solutions
Step 1: Prior to placement onto the cash drawer, route cords
for devices to be mounted on Topper through and around half-
moon support extensions.
Step 2: If attaching a device to the center location (Figure 1),
add the mount and hardware now.
•For devices that are not mounted, cords can be routed through
an open hole or placed in a pass-through plug (Figure 2).
•If using Architect configured mounts by SpacePole®the flange
ring fits on the underside of the Topper, with the bolts coming
through the top from the peripheral base.
•Keep cords secure and flat against underside of Topper to allow
for proper fit when placing on cash drawer, included cable ties
and adhesive pads can be used for this process.
•Locations adjacent to the center mount, with 4 pilot holes, can
be drilled with a ¼” bit to allow for adjusted hardware/device
positions.
Architect™Tech Mount instructions on back
C-000-085 support@apgsolutions.com | www.apgsolutins.com | 1 of 2
Figure 1 Figure 2 Figure 3 Figure 4
Step 3: If pairing the Topper with the customer facing Tech Mounts skip to instructions on back
now.
Step 4: Place Topper onto the cash drawer, aligning back inner two tabs to rest against the back of
drawer.
•Topper should push and snap into place.
•The open ‘garage’ area behind the drawer is for additional cord and power management.
Step 5: Insert solid plugs into open holes on the top and back of Topper (Figure 3 and Figure 4).
Step 6: Devices can be connected to mounts or placed on Topper in preparation for use.
C-000-085 [email protected] | www.apgsolutions.com | 1 of 2
Architect™Tech Mounts
Step 1: Before connecting the Tech Mounts to the Topper,
attach device hardware to the Tech Mounts following the
same step as with Topper.
-Attaching hardware is much easier than after being connected to
the Topper.
Step 2: Start connection of Tech Mounts to Topper using 2
tee-nuts, shown in Figure 5, per mount. Start by inserting,
and twisting, tee-nut from inside the mount. The two raised
grips around the hold will capture and hold the side notches
on tee-nut, see Figure 6.
-Position the connectors in two holes diagonal of each other, two
holes will remain open.
Step 3: Connect Tech Mount by positioning against
corresponding holes on Topper and rotate thumb screws,
from inside the Topper, into tee-nuts to secure the mounts.
-A coin can be used to help turn thumb screw - you do not need
to overtighten.
Step 4: Place Topper and connected Tech Mounts onto the
cash drawer, aligning back inner Topper tabs to rest against
the back of drawer.
Step 5: Attach peripheral device(s) to hardware on Tech
Mounts, connect and route cables/wires through open hole(s)
into the ‘garage’ area. Connect your Minota® cash drawer,
printer, and other devices according to your technology
setup.
-If Tech Mounts do not have attached devices the main hole can
be filled with a solid plug, Figure 7.
Step 6: The Architect is sized and designed for an Epson TM-
m30II printer to nest between both Tech Mounts, there is a
3/8” gap under the Topper edge to pass cords to and from
the printer, see Figure 8.
*Tech Mounts can be
positioned and mounted
in an open position
C-000-085 [email protected] | www.apgsolutions.com | 2 of 2
Figure 8
Figure 7
Figure 6
Figure 5
Table des matières
Autres manuels APG Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
