Aperia Technologies Halo Connect Manuel utilisateur
USER MANUAL
IN-202UM
Keep this manual in the vehicle
for future reference.
Failure to follow the instructions and safety precautions
in this manual may result in the product detaching
from the vehicle, tire blowouts, and/or loss of vehicle
control, which may result in serious injury or death.
Safety
SAFETY WORDS AND SYMBOLS
Please pay attention to special symbols used through this manual
to convey important information. Hazard signal words such
as WARNING, CAUTION, or NOTICE are used throughout this
manual. Information accented by these words indicates a point of
emphasis and importance. The following denitions comply with
ANSI Z535.6 and indicate the use of signal words as they appear
within this manual.
OTHER HELPFUL WORDS AND SYMBOLS
The following symbols are used throughout the manual to help
guide you in your work with the Halo Tire Inator.
VISUAL CHECK
SOUND CHECK
A sound check symbol describes a
critical noise that should be heard and
and accompanying instructions that
should be followed.
A visual check symbol describes a critical
observation that the user should see and
accompanying instructions that should be
followed.
This is the safety alert symbol. It is used to
alert you to potential physical injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
WARNING indicates a hazardous situation
that, if not avoided, could result in serious
injury or death.
CAUTION indicates a hazardous situation
that, if not avoided, could result in minor or
moderate injuries.
NOTICE is used to address practices which
could result in damage to equipment or
property.
3
Safety
IMPORTANT SAFETY INFORMATION
The Halo and its components should be installed and maintained
in accordance with the instructions in this manual. Proper
installation and maintenance of the Halo is critical to ensure safe
use of the device. Failure to do so may result in injury or death,
tire damage or failure, and/or damage to other equipment or
property. Carefully read, understand and follow all safety related
information within this manual.
Regular tire pressure checks required.
The Halo is not intended to replace regular pressure-checks
and tire maintenance practices as specied by the FMCSA
in their Compliance, Safety, Accountability (CSA) Program.
Aperia encourages users to take care of their tires and Halos,
both of which are important to their safety.
DO NOT modify parts without authorization
DO NOT modify or rework parts without written authorization
from Aperia. Use ONLY Aperia authorized replacement parts.
Use of substitute, modied or replacement parts not authorized
by Aperia may not meet Aperia's specications and may
result in failure of the part and possibly injury or death. Obtain
authorized replacements by contacting customer support.
Use PPE and follow all safety regulations
To prevent injury, always use personal protective equipment
(PPE) and follow all federal, state, local and employer safety
regulations, as appropriate, when installing or maintaining
the Halo. PPE includes proper footwear, eye protection, and
gloves.
4
Roadside Call Instructions
If a roadside call occurs, please present the technician with
this user manual. Refer the technician to the Important Safety
Information and Halo Uninstallation sections. If additional
assistance is required, please contact Customer Support or
visit aperiatech.com/literature.
5
Contents
3 Safety
3 Safety Words and Symbols
4 Important Safety Information
6 Introduction
6 The Halo Tire Inator
6 Halo Benets
7 About this Manual
7 Online Product Literature
7 Contact Aperia
8 Getting Started
8 System Components
9 Installation Tools
10 Installation Overview
11 Halo Installation
11 Prepare the Vehicle
11 Verify Pressure and Orient Halo
12 Install Bracket - Tractor
14 Install Bracket - Trailer
16 Attach Hoses to Tire Valve Stems
18 Attach Hose(s) to Halo
20 Orient Halo on Bracket
21 Tighten Center Mounting Screw
22 Final Check
23 Halo Uninstallation
26 Halo Maintenance
26 Maintenance Table
26 Maintenance Actions
33 TorqueSpecicationsTable
INTRODUCTION
Tire under-ination is a well-known problem in the trucking
industry. Research from the Federal Motor Carrier Safety
Administration (FMCSA) shows that fewer than 55% of all truck
tires are within 5 PSI of their target tire pressure. This means
billions of dollars are lost each year due to increased fuel
consumption, tread wear, tire blowouts and other operational
issues. According to a eld test conducted by the U.S.
Department of Transportation, optimal tire ination can save a
eet over $2,200 annually per tractor-trailer while saving time
and improving safety.
The Halo Tire inflator
Aperia Technologies is proud to offer the Halo Tire Inator as
the leading retrot, auto-ination solution for both tractors and
trailers. The Halo is a completely mechanical, rotational pump,
compatible with dual or wide-base tires and is the rst standalone
tire ination technology for medium- and heavy-duty vehicles.
As an easy-to-install, bolt-on device, it can be mounted in 5-10
minutes per wheel-end and does not require connection to an
onboard air compressor.
Halo benefits:
Increases Fuel
Efciency
Reduces Tread
Wear Fewer Blowouts
Fleet Protability Prevents
Accidents Maximizes Up-Time
Extends Casing
Life
Simplied
Maintenance Reduces Emissions
6
ABOUT THIS MANUAL
This user manual is provided to support the installation and
maintenance of the Halo Tire Inator on new or in-service
tractors and trailers.
The descriptions and specications provided in this manual
are current at time of publication.
ONLINE PRODUCT LITERATURE
The most up-to-date version of the Halo User Manual
and additional product literature covering the installation,
maintenance, and service of accessories and add-on items
can be found online at:
www.aperiatech.com/literature
CONTACT APERIA
Contact Aperia Customer Support via phone or email for
technical or sales assistance.
Phone +1 (844) RUN-HALO
Websitewww.aperiatech.com
Sales [email protected]
Support [email protected]
7
Getting started
Tractor Bracket Kit Trailer Bracket Kit
One component or kit from each category is required for a
complete wheel-end installation.
SYSTEM COMPONENTS:
or
b
Inner Dual Hose
Outer Dual Hose
a
a
b
Wide-base Hose
Conversion Cap
a
a
b
b
HALO
BRACKET KIT
HOSE KIT
or
8
INSTALLATION tools
REQUIRED
• Impact driver and socket for hub nuts (Drive axle installs)
• Torque wrench (capable of measuring 15 to 50 ft-lb)
• Torque wrench (capable of measuring 100-250 ft-lb)
• Socket wrench
• Socket extension
• 5/8" socket (Halos with hex head center screw)
• 5/16" hex bit socket (Halos with socket head cap screw center screw)
• T50 Security Torx bit socket (Halos with tamper-resistant center screw)
• 1/2” deep socket (Trailer style hubcap installs)
• 5/8” xed wrench
• Channellock pliers
• Soapy water mixture in a spray bottle
Recommended
• Permanent marker/paint pen
9
INSTALLATION OVERVIEW
A general overview of the installation steps for the Halo Tire
Inator are shown below. Do not install without referring to the
"Install" section for complete details.
1a. VERIFY PRESSURE 1b.ORIENTHALO
(LEFT/RIGHT)
R
O
T
A
T
I
O
N
2.INSTALLBRACKET 3.ATTACHHOSE(S)TO
TIREVALVESTEM
4.ATTACHHOSE(S)
TOHALO
7.FINALCHECK
PSI
5.ORIENTHALOON
BRACKET
10
6.TIGHTENCENTERBOLT
Autres manuels pour Halo Connect
1
Table des matières
Autres manuels Aperia Technologies Outils électriques
