Apera PC60-Z Manuel utilisateur

2401T-F Conductivity/Temp. Electrode

User Manual

Brief Introduction

Apera Instruments 2401T-F Conductivity Electrode is featured with a proprietary platinum black sensor

for accurate readings in a wide conductivity range up to 200 mS/cm, along with a built-in temperature

sensor for automatic temperature compensation.

Technical Specifications

Range

0 to 200 mS/cm, 32 to 122°F (0 to 50°C)

Housing

Lead-free Glass

Constant

K=1.0

Connector

BNC/RCA

Cable length

3 Ft

Dimension

ø12*145 mm

Temperature sensor

30KΩ thermistor

Operating temperature

32 to 176°F (0 - 80°C)

How to Install the Electrode

1. Find the conductivity BNC socket (where it shows Cond) on the conductivity meter; Open the

rubber cap; Insert the BNC connector of the electrode to the BNC socket while twisting clockwise

until it’s locked.

2. Find the RCA socket (where it shows temp.) on the pH meter; Open the rubber cap; Insert the

black RCA connector of the electrode to the RCA socket directly.

3. After connecting the new electrode to your meter, adjust the meter’s constant K to 1.0 according

to the instruction of your meter’s manual. Then perform a 2 to 3-point calibration to ensure the

accuracy.

How to Use the Electrode

1. There is a proper amount of deionized water in the cap on top of the electrode. The conductivity

sensor is soaked in it to keep its sensitivity.

2. Before measuring, loosen the bottle cap, then pull out the electrode while twisting

counterclockwise. Place the storage bottle at a safe position.

3. Rinse the electrode with distilled or deionized water and blot-dry it with clean tissue or filter paper.

Rinse the electrode again with your test solution if possible for the best result. Never rub the

sensor.

4. Insert the electrode into your sample solution and stir it for a few seconds in the solution to

remove potential air bubbles. Then wait for the stable reading and take the measurement.

5. After measurement, insert the electrode back into the storage cap and twist it on. If the water in

the cap is contaminated, rinse out the storage cap and fill in new deionized or distilled water.

How to Maintain the Electrode

1. Always rinse the electrode with distilled or deionized water before and after each test and

calibration.

2. For organic residues, rinse the electrode with warm detergent water; For calcium and magnesium

sediments, use 10% lemon acid to clean them off.

3. Store the electrode in the storage cap filled with distilled or deionized water when not in use.

4. Keep the electrode connector clean and dry. Use cotton balls with isopropyl alcohol to clean if it

gets dirty and then blow-dry it. This is to prevent a potential short circuit, which will undermine the

electrode’s performance.

Limited Warranty

We warrant this electrode to be free from defects in material and workmanship and agree to repair or

replace free of charge, at the option of APERA INSTRUMENTS, any malfunctioned or damaged

product attributable to responsibility of APERA INSTRUMENTS for a period of SIX MONTHS from the

delivery.

This warranty does not cover any damages due to:

Accidental damage, transportation, storage, improper use, failure to follow the product instructions,

unauthorized repair, normal wear and tear, or any other actions or events beyond our reasonable

control.

APERA INSTRUMENTS (Europe) GmbH | Wilhelm-Muthmann-Str.18, 42329 Wuppertal, Germany

info@aperainst.de | www.aperainst.de | Tel.: +49 202 51988998

Autres manuels pour PC60-Z

Table des matières

Autres manuels Apera Instrument de mesure

Apera

Apera TDS20 Manuel utilisateur

Apera

Apera 201DJ-C Manuel utilisateur

Apera

Apera LabSen 232 Manuel utilisateur

Apera

Apera EC400S Manuel utilisateur

Apera

Apera PC60-Z Manuel utilisateur

Apera

Apera TN400 Manuel utilisateur

Apera

Apera PH60S Manuel utilisateur

Apera

Apera 2310T-S Manuel utilisateur

Apera

Apera LabSen 371 Manuel utilisateur

Apera

Apera PH400S Manuel utilisateur

Apera

Apera PH700 Manuel utilisateur

Apera

Apera SX811-SS Manuel utilisateur

Apera

Apera SX811-BR Manuel utilisateur

Apera

Apera ORP60-Z Manuel utilisateur

Apera

Apera ORP60 Manuel utilisateur

Apera

Apera DO850 Manuel utilisateur

Apera

Apera 201DJ-C Manuel utilisateur

Apera

Apera LabSen 252 Manuel utilisateur

Apera

Apera DJS-0.1-C Manuel utilisateur

Apera

Apera PC60-Z Manuel utilisateur

Apera

Apera PC60 Manuel utilisateur

Apera

Apera 2310T-F Manuel utilisateur

Apera

Apera PH60 Manuel utilisateur

Apera

Apera PC60-Z Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur