APart-Audio ZONE4R Manuel utilisateur
ZONE4R
Instruction manual
Instruction manualZONE4R 1
ZONE4R Manual
2ZONE4 controls
Introduction
ZONE4R remote panel is designed for use with the Apart-audio ZONE4 preamplifier
only. Wiring is easy, using industry standard CAT5 (or higher) computer network
cable. Both T-568A and T-568B cable terminations can be used.
It is possible to use more than one ZONE4R remote panel per zone. Maximum
number of remote panels per ZONE4 preamplifier is 8 panels in any configuration
: e.g. 2 panels x 4 zones = 8 panels or 8 panels x 1 zone = 8 panels or any other
combination with a maximum of 8 panels in total.
Do not connect the ZONE4 or the ZONE4R remote panel to a computer network,
this will cause serious damage to the computer network and the ZONE4/R units !
Instruction manualZONE4R 3
Front panel and operation
4 5 6 7
1 2 3
4ZONE4 controls
1. Music level control: this knob has the same functionality as the music level
knob on the ZONE4 main unit. Turn the knob to adjust the music level. The
actual value is displayed on the screen ‘2’ for a few seconds. Push the knob to
mute the music, the mute status is indicated by led ‘4’.
2. Display: this shows the selected music (line) source ‘A to D’ or the music or
microphone levels. When a value has been edited, the display lights up more
strongly during a few seconds. After a few seconds, the display will show
the selected music source again. Please note that after some time of non-
operation, the intensity of the display will dim automatically.
3. Micro mix level control: this knob has the same functionality as the micro mix
level knob on the ZONE4 main unit. Turn the knob to adjust the micro mix
level. The actual value is displayed on the screen ‘2’ for a few seconds.Push the
knob to mute the micro mix, the mute status is indicated by led ‘7’.
Instruction manualZONE4R 5
4. Music level mute led: this led lights up when the music is muted.
5. Line input selector switches (music) : use these switches to scroll downward
through line input A to D. The selected input is shown in the display ‘2’.
6. Line input selector switches (music) : use these switches to scroll upward
through line input A to D. The selected input is shown in the display ‘2’.
7. Micro mix mute led: this led lights up when the micro mix is muted.
6ZONE4 controls
ZONE4R connector and wiring details
1. Ground connection (GND) -> connect to RJ45 pin 1 and 3 and 7 (colours : see
table below)
1234
Instruction manualZONE4R 7
1234
RJ45 pin1
2. Data connection (Rx B) -> connect to RJ45 pin 4 (colours : see table below)
3. Data connection (Tx A) -> connect to RJ45 pin 5 (colours : see table below)
4. Power supply (+12VDC) -> connect to RJ45 pin 2 and 6 and 8 (colours : see
table below)
RJ45 connections on rear of ZONE4 main unit ‘to zone remote wall panels’ :
8ZONE4 controls
Pin number RJ45 T-568A cable colour
code
T-568B cable colour
code
EUROBLOCK 4
(See picture above)
Pin 1: GND white – green white – orange connector 1
Pin 2: 12 VDC green orange connector 4
Pin 3: GND white – orange white – green connector 1
Pin 4: RX B blue blue connector 2
Pin 5: TX A white – blue white – blue connector 3
Pin 6 12 VDC orange green connector 4
Pin 7: GND white – brown white – brown connector 1
Pin 8: 12 VDC brown brown connector 4
Autres manuels pour ZONE4R
1
Table des matières
Autres manuels APart-Audio Panneau de contrôle
