AnyTone AT-5555 Manuel utilisateur

AT-5555 RADIO USER’S MANUAL

TABLEOFCONTENTS

WARNIGN

RESET FUNCTION

FUNCTIONS & FEATURES

INSTALLATON

Where and how to Mount Your CB Radio

Antenna Installation

Power Connection

Basic Operation

Adjustment of SWR (Standing Wave Ratio)

HOW TO USE YOUR CB

LCD DISPLAY

FRONTPANEL

PEARPANEL

PRESS-TO-TALK MICROPHONE

FUNCTION MENU SETUP

OPERATING PROCEDURETORECEIVE

OPERATINGPROCEDURETOTRANSMIT

SPECIFICATION

WARNIGN

To use the radio, please connect the antenna to the location “B” on the back panel of the

equipment firstly and then set the SWR (Standing Wave Ratio) before transmitting. Failure

to do so may result in destruction of the power amplifier, which is not covered by the

guarantee.

Welcome to Use

Welcome to the world of new CB radios. The new AT-5555 Radio provides you with top

performance and best visual enjoyment. With the use of SMT technology to guarantee the

best stability, reliability and unprecedented quality, your multi-functional AT-5555 Radio

10-meter Radio is a new step in personal communication and is surely the best choice for

professional users of CB radios. Moreover, with multiple connecting ports in the radio,

AT-5555 Radio is ready for future upgrading and functions expanding. To ensure that you

use the radio to the fullest, please read this manual carefully before installing and using

your AT-5555 Radio.

RESET FUNCTION (Resume Factory Default)

This CB Radio introduces RESET FUNCTION to prevent accidents and provide a solution

for customers who changed some functions unconsciously and do not know how to

resume normal settings. The CB Radio will resume factory default once this function is

activated.

How to Operate:

Step 1: Power off the radio

Step 2: Press and hold FUNC and SCAN keys at the same time, then release followed

All former settings would be replaced by Factory Default value when LCD displays

"REND"

WARNING: All former settings would be replaced by Factory Default value after operating

the RESET FUNCTION.

FUNCTIONS & FEATURES

1. Big LCD which displays frequency and all kinds of information

2. DUAL-DIGITAL TUBE FOR CHANNEL DISPLAY

3.USE EL technology for backlight

4. PAǃCWǃAMǃFMǃUSBǃLSB mode

5. AǃBǃCǃDǃEǃF , 6 bands in total, with 60 channels at most in each band to be

programmed.

6. Frequency Tuning Step can be 10HZ, 100HZ, 1KHZ or 10KHZ.

7. Multiple CLARIFIER Operating Modes

8. Flexible menu functions and PC programming software to meet varied customer

demands

9. ECHO Function

Release the two keys when LCD displays "RES".

by power on the radio.

Step 3:

10. SQ, ASQ Function (FM and AM mode only)

11. RF GANI ADJUSTMENT

12. RF PWR ADJUSTMENT

13. SCAN FUNCTION

14. RB FUNCTION

15. NB/ANL FUNCTION

16. DW DUAL-WATCH FUNCTION

17. BEEP VOICE PROMPT

18. +10KHZ Function

19. SWRǃS/RFǃDC Voltage display function

20. TOT function

21. HIˉCUT FUNCTION

22. EMG CALL

23. SWR PROTECTION

24. POWER SUPPLIED VOLTAGE PROTACTION

25. Key-Lock Function

INSTALLLATON

WHERE AND HOW TO MOUNT YOUR MOBILE CB RADIO

a) You should choose the most appropriate setting from a simple and practical point of

view

b) Your CB radio should not interfere with the driver or the passengers.

c) Remember to provide for the passing and protection of different wires (e.g.: power,

antenna, accessory cabling) so that they do not in any way interfere with the driving of

vehicles.

d) To install your equipment, use the cradle (1) and the self-tapping screws [2] provided

(drilling diameter 5 mm). Take care not to damage the vehicle’s electrical system while

drilling the dash board.

e) Do not forget to insert the rubber joints [3] between the CB and its support as these

have a shock-absorbing effect which permits gentle orientation and tightening of the

set.

f) Choose where to place the microphone support and remember that the microphone

cord must stretch to the driver without interfering with the controls of the vehicle.

2) ANTENNA INSTALLATION



a) Choosing your antenna:



For CB radios, the longer the antenna, the better its results. Your dealer will help you with

your choice of antenna.

b) Mobile antenna:



-Must be fixed to the vehicle where there is a maximum of metallic surface(ground plane) ,

away from windscreen mountings.

-There are two types of antenna: Pre-Regulated Antenna which should be used on a good

ground plane (e.g. car roof or lid of the boot), and Adjustable Antenna which offer a much

larger frequency range and can be used on a smaller ground plane.

For an antenna which must be fixed by drilling, you will need a good contact between the

antenna and the ground plane. To obtain this, you should lightly scratch the surface where

the screw and tightening star are to be placed.

-Be careful not to pinch or flatten the coaxial cable (as this runs the risk of break down

and/or short circuiting).

-Connect the antenna to location (B).

c) Fixed antenna:

A fixed antenna should be installed in a space as clear as possible. If it is fixed to a mast,

it will perhaps be necessary to stay it, according to the laws in force (you should seek

professional advice). All AT-5555 antennas and accessories are designed to give

maximum efficiency to each CB radio within the range.

3) POWER CONNECTION



Your RADIO is protected against an inversion of polarities. However, before switching it

on, you are advised to check all the connections. Your equipment must be supplied with a

continued current of 12 volts (A). Today, most cars and lorries are negative earth. You can

check this by making sure that the negative terminal of the battery is connected either to

the engine block or to the chassis. If this is not the case, you should consult your dealer.

WARNING: Lorries generally have two batteries to supply a voltage of 24 volts, in which

case it will be necessary to insert a 24/12 volt converter into the electrical circuit. The

following connection steps should be carried out with the power cable disconnected from

the set.

a) Check whether the battery is of 12 volts.

b) Locate the positive and negative terminals of the battery (+is red and –is black).

Should it be necessary to lengthen the power cable, please use the same or a superior

type of cable.

c) It is necessary to connect your CB to a permanent (+) and (-). We advise you to

connect the power cable directly to the battery (as the connection of the CB cable to the

wiring of the car-radio or other parts of the electrical circuit may, in some cases, increase

the possibilities of interference).

d) Connect the red wire (+) to the positive terminal of the battery and the black (-) wire to

the negative terminal of the battery.

e) Connect the power cable to your CB radio.

WARNING: Never replace the original fuse (10A) by one of a different value.

BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING YOUR SET FOR THE

FIRST TIME(without transmitting or using the <<Push-To-Talk>> switch on the

microphone)

a) Connect the microphone

b) Check the antenna connections

c) Turn the set on by turning the volume knob clockwise

d) Turn the squelch knob to minimum

e) Adjust the volume to a comfortable level

f) Go to channel 20@D band by using either the UP or DN key on the microphone or the

rotary knob.

5˅ADJUSTMENT OF SWR(standing wave ratio)

WARNIGN: This must be carried out when you use your CB radio for the first time (and

whenever you re-position your antenna). The adjustment must be carried

out in an obstacle-free area.

5) Adjustment with a built-in SWR meter or external SWR meter

a) To connect the SWR meter

Connect the SWR meter between the CB radio and the antenna as close as possible

to the CB radio (use a maximum of 40cm cable)

b) To adjust the SWR meter 

-Set the CB to channel 20@D band in FM

-put the switch on the SWR meter to position CAL or FWD

-Press the <<Push-To-Talk>> switch on the microphone to transmit

-Bring the index needle to !by using the calibration key

- Change the switch to position SWR (reading of the SWR level). The reading on the

meter should be as near as possible to 1. If this is not the case, re-adjust your antenna to

obtain a reading as close as possible to 1.( An SWR reading between 1 and 1.8 is

acceptable).

-It will be necessary to re-calibrate the SWR meter after each adjustment of the antenna.

6) HOW TO USE INTERNAL SWR METER-Set CB to channel 20@D band in FM

-Press <<push-to-talk>> button on the microphone to transmit

-At the moment, LCD would display SWR value which should be as close as possible to 1.

If this is not the case, re-adjust your antenna to obtain a SWR value as close as possible

to 1 (an SWR reading between 1 and 1.8 is acceptable).

HOW TO USE YOUR CB RADIO

7 digits: Display frequency and any other information

Indicating bars: Indicate RX, RSSI, PA, PWR, SWR

The first decimal point: Appears when current channel is edited with SCAN DEL.

FUNC˖Appears after pressing FUNC key

AQ˖Appears when ASQ function is started (only for AM/FM)

RB˖Appears when Roger beep function is started (enabled)

NB/ANL: Appears when NB/ANL function is started (enabled)

BP˖Appears when BP function is started (enabled)

ECHO: Appears when ECHO function is started (enabled)

VOIC: Appears when VOIC function is started. It is disabled in this CB radio.

HIˉCUT˖Appears when HIˉCUT function is started

DW: Appears when DW function is started

10K: Appears when +10KHZ function is started

EMG: Appears when EMG channel is used

SWR: Appears when SWR is used

SRF: Appears when S/RF is used

SC: Appears when SCAN is used

PAǃCWǃAMǃFMǃUSBǃLSB: Indicate different operating modes

1. Appears when CLARIFIER function is FINE operation.

2. Appears when CLARIFIER FUNCTION is COARSE operation or RT operation.

3. Appears when CLARIFIER FUNCTION is transmitting frequency regulated.

<FRONTPANEL>

1. OFF/ON/VOLUME˄Inner Dual Concentric˅.

Turn clockwise to switch on the CB radio and set desired volume level. Under normal

operating state, the VOLUME control is used to adjust the output volume obtained either

by the transceiver speaker or the external speaker or the external PA speaker, if used.

2. SQUELCH (Outer Dual Concentric)

This control is used to cut off or eliminate receiver background noise in the absence of an

incoming signal. For maximum receiver sensitivity, it is desired that the control be

adjusted only to the point where the receiver background noise or ambient background

noise is eliminated. Turn fully anticlockwise then slowly clockwise until the receiver noise

disappears. Any signal to be received must now be slightly stronger than the average

received noise. Further clockwise rotation will increase the threshold level which a signal

must overcome in order to be heard. Only strong signals will be heard at a maximum

clockwise setting.

3. ECHO˄Inner Dual Concentric˅This switch is used to control echo effect.

4. TONE (Outer Dual Concentric)

This switch is used to control intervals of echo sound

5. RF GAIN˄Inner Dual Concentric˅

This switch is for adjusting sensitivity during reception. For long distance communications

RF GAIN should be set to maximum. RF GAIN can be reduced to avoid distortion, when

your correspondent is close by and when he does not have RF POWER. The normal

setting of this function is on maximum (fully clockwise).

6. RF POWER (Outer Dual Concentric)

Adjustment of the output power is for AM and FM mode only. Reducing the power is

allowed when communicating with a person who has no RF GAIN. The normal position of

this function is set to maximum, fully clockwise.

7. BAND SELECTOR

Rotate this switch to select A, B, C, D, E, F band of operation

8. MODE(PA/CW/AM/FM/USB/LSB)

This switch allows selecting the modulation mode PA, CW, AM, FM, LSB or USB. Your

modulation mode has to correspond with the one of your correspondent. The mode

selector changes the mode of operation of both transmitter and receiver simultaneously.

Frequency Modulation / FM: for nearby communications on a flat open field.

Amplitude Modulation / AM: Communication on a field with relief and obstacles in

middle distance (the most used).

Upper and Lower Side Band / USB-LSB: Used for long distance communications

(according to the propagation conditions).

9. CLARIFIERThis is frequency tuning knob which can be set as different modes (refer to CLA

Specifications in Functions Menu for more details)

10. PUSHThis is PUSH Key which can be set as different modes (refer to PSH specifications under

Functions Menu for more details)

11. CHANNEL SELECTOR

Rotate this switch to select any desired channel from forty citizens band channels. The

selected channel appears on the LED directly above the channel selector knob.

12. CHANNEL INDICATOR

Numbered LED indicates the selected channel you wish to operate on.

Table des matières

Autres manuels AnyTone Radio

AnyTone

AnyTone DORIS Manuel utilisateur

AnyTone

AnyTone AT-588 Manuel utilisateur

AnyTone

AnyTone GRACES Manuel utilisateur

AnyTone

AnyTone AM-580 Manuel utilisateur

AnyTone

AnyTone Ares Manuel utilisateur

AnyTone

AnyTone AT-310M Manuel utilisateur

AnyTone

AnyTone METIS Manuel utilisateur

AnyTone

AnyTone AT-500M Manuel utilisateur

AnyTone

AnyTone AT 778 Manuel utilisateur

AnyTone

AnyTone D578UV Manuel d'utilisation et d'entretien

AnyTone

AnyTone ARES II Manuel utilisateur

AnyTone

AnyTone Dual Band FM Transceiver Manuel utilisateur

AnyTone

AnyTone AT- 778UV Manuel utilisateur

AnyTone

AnyTone AT-3318UV Manuel utilisateur

AnyTone

AnyTone AT-5189 Manuel utilisateur

AnyTone

AnyTone AT-300M Manuel utilisateur

AnyTone

AnyTone AT-D578UV Guide de configuration

AnyTone

AnyTone AT-D868UV Mode d'emploi

AnyTone

AnyTone APOLLO I Manuel utilisateur

AnyTone

AnyTone AT-598 Manuel utilisateur

AnyTone

AnyTone AT-398UV Manuel utilisateur

AnyTone

AnyTone ARES II Manuel utilisateur

AnyTone

AnyTone DMR AT-D878U Manuel utilisateur

AnyTone

AnyTone AT-D578UV Manuel utilisateur

Manuels Radio populaires d'autres marques

EisSound

EisSound KBSound iSelect Manuel utilisateur

Midland

Midland 1001LWX Manuel utilisateur

Konig

Konig HAV-SR41 Manuel utilisateur

Roberts

Roberts exprssion Manuel utilisateur

VDigi

VDigi DD3.0 Manuel utilisateur

Radio Shack

Radio Shack 21-1863 Manuel utilisateur

Roberts

Roberts Stream 207 Manuel utilisateur

Sony

Sony Walkman SRF-M97 Manuel utilisateur

Stanley

Stanley FatMax FMC770 Manuel utilisateur

auna

auna DAB-Radio 10026947 Manuel utilisateur

SOUNDMASTER

SOUNDMASTER UR190 Manuel utilisateur

HYT

HYT TC-320 Manuel utilisateur

auna multimedia

auna multimedia Yellowstone 10026851 Manuel utilisateur

B-Tech

B-Tech GMRS-V2 Manuel utilisateur

Weierwei

Weierwei VEV-V8 Manuel utilisateur

SOUNDMASTER

SOUNDMASTER DAB750 Manuel utilisateur

Telefunken

Telefunken TF-1505 Manuel utilisateur

Makita

Makita LXRM03 Manuel utilisateur