AnyTone Ares Manuel utilisateur
USER'S MANUAL
CONTENTS
FUNCTIONS & FEATURES..................................................................1
STANDARD ACCESSORIE..................................................................2
OPTIONAL ACCESSORIE ....................................................................2
INSTALLATION.....................................................................................2
GETTING ACQUAINTED......................................................................6
HOW TO USE YOUR RADIO ...............................................................8
SLIDE SWTICH.....................................................................................9
ERROE CODE ....................................................................................10
SPECIFICATIONS...............................................................................11
1
FUNCTIONS & FEATURES
FM/AM/PA mode
◆
Weather Channel 150-170MHz programmable(Optional)
◆
CTCSS/DCS Code(Optional)
◆
PWR, RX RSSI S-Meter
◆
PC programmable
◆
Echo Function
◆
SQ, ASQ Function
◆
RF Gain Adjustment
◆
Mike Gain Adjustment
◆
H/L power
◆
Programmable RB
◆
NB/ANL Function
◆
Offset Function
◆
Beep Voice Prompt
◆
+10KHz Function
◆
TOT Function
◆
HI-CUT Function
◆
Busy channel lock
◆
Monitor
◆
LED Brightness Adjustment
◆
SWR Protection
◆
Voltage Protection
◆
2
STANDARD ACCESSORIES
OPTIONAL ACCESSORIE
INSTALLLATON
Radio
Screws for
bracket
DC Power
Cable
USB Programming
Cable
External Speaker
Self-tapping
Screws
Microphone
Pads for
bracket
PadsAdjusting
screws
Microphone
Hanger
Mounting Bracket Non-slip
Mat
Spare Fuses
(10A,250V)
Choose the most appropriate setting from a simple and
practical point of view. Your radio should not interfere
with the driver or crash the driver's knee or leg when
rush brake.
Using the self-tapping screws and pads(2 sets) to x 1.
the bracket.
Put the Non-slip mat on the 2 ends of the bracket and put in the radio. Then insert2.
the adjusting screws and check careful each screws, make sure the screws and
machine will not loose when the car shaking.
Choose suitable angle by the 3 screw holes in the two ends of bracket.3.
3
Microphone connection
Plug microphone connector into jack.1.
Pull on the screw for microphone connector.2.
MIC
VOL
SQ
MIG
OFF
RFG
PA
FM
AM
B
CD
E
TONE
ARES
DATA
RX/TX
BAND
HH
DIM
MON
RF PWR
HI
NB/ANL
ANL
OFF
LO
OFF
+1OK
M
LL
OFF
BAND
AF
TX
PWR
+30dB
23
4
9
753
1
S G
1
MIC
VOL
SQ
MIG
OFF
RFG
PA
FM
AM
B
CD
E
TONE
ARES
DATA
RX/TX
BAND
HH
DIM
MON
RF PWR
HI
NB/ANL
ANL
OFF
LO
OFF
+1OK
M
LL
OFF
BAND
AF
TX
PWR
+30dB
23
4
9
753
1
S G
1
ANTENNA INSTALLATION
POWER CONNECTION
Before using this radio, please install a high efficent and harmonious adjusted
CB antenna, suitable antenna type and correct installation will bring excellent
communication.
To match with the radio, the antenna and cable shall with characteristic impedance of
50ohm, or the antenna system will not efcient enough and will disturb TV, radio or other
electronics.
Screw the antenna connector into the antenna jack.1.
Grounding the antenna system to ensure best performance of this radio.2.
This radio adopt 13.8V power supply, never connect it to 24V battery, And the 13.8V car
battery shall with sufcient current, or the LCD will become dark and Transmit power
will drop down.
The position of antenna can be put as following example:3.
WARNING:
▲ Connect antenna rstly before transmiting, or it might damage the radio.
▲ To avoid the risk of fire, electric shock, radio damage, all base station shall
equip of lightning protector
▲ Be sure choose a matching antenna, you may enquiry our dealers.
4
Connect positive red power cable with the + terminal of the battery.1.
Connect negative black power cable with the - terminal of the battery.2.
Connect the DC power cable to the transceiver's power supply connector.3.
▲ We suggest not use cigar lighter as it often bring down the voltage.
▲ Locate the power cable away from high temperature, moisture, portre and cable
insulator.
▲ Use a full power cable even it is longer than need, do not take off the fuse holder
from the cable.
Connected
to chassis
Replacing Fuse
This radio adopt 10A, 250V fuse.
If the fuse blows, determine the reason, then correct the problem.
After the problem is resolved, replace the fuse. If newly installed fuses continue to
blow, disconnect the power cable and contact your autho-rized dealer or an authorized
servicecenter:
Pull the two fuse cover in difference direction and open it.1.
,
IN-LINE
FUSE HOLDER
Replace the broke fuse with good one, and close the fuse holder.2.
Be sure to use suggested fuse, or it might damage the radio.3.
FUSE
IN-LINE
FUSE HOLDER
IN-LINE
FUSE HOLDER
IN-LINE
FUSE HOLDER
10A 250V FUSE
5
Install External Speaker
If use an external speaker, please choose 8ohm speaker with 3.50mm mono band
(doulbe cable) plug.
Locate the external speaker in a suitable place.1.
Plug into the speaker jack.2.
Install Microphone Hanger
Choose a ideal location which will not interfere
the driver. Using supplied self-tapping screws and
pads(2 sets) to x the hanger.
6
GETTING ACQUAINTED
Front Panel
No. Functions
1S-Meter
2 Control NB/ANL function on/off
3 Control power level
4 Control Monitor/10K on/off
5Control LED brightness
6 Choose H and L band group
7 TX/RX indicator
8 PC programming port
9 Channnel dispplay
10 Mike connector
11 Power on/off volume level control
12 Squelch level control
13 Control Mike gain level
14 Control RF gain level
15 Choose AM/FM/PA mode
16 Choose working band
17 Control echo rebound times
18 Control echo duration time
19 Channel Switch
MIC
VOL
SQ
MIG
OFF
RFG
PA
FM
AM
B
CD
E
TONE
ARES
DATA
RX/TX
BAND
HH
DIM
MON
RF PWR
HI
NB/ANL
ANL
OFF
LO
OFF
+1OK
M
LL
OFF
BAND
AF
TX
PWR
+30dB
23
4
9
753
1
S G
1
1
10 15 16 1912 1814
2 3 4 5 6 7 98
11 13 17
7
Microphone
Rear Panel
Channel Down Channel UP
Microphone cable
Mic
PTT
Connector
No. Functions
20 External SP Jack
21 External PA Jack
22 Antenna Jack
23 Power Supply Jack
20
23
22 21
ANT.
PA.SP. EXT.SP.
POWER
-
+
8
Squelch Control
RF Gain Control
Mic Gain Control
Working mode Control
Working Band Control
Echo times Control
Echo duration Control
When the radio is standby, turn SQ outter shaft clockwise to adjust squelch level.
When the radio is receiving, turn RFG outter shaft to adjust RF gain. Turn it clockwise
to increase gain, anti-clockwise to reduce gain.
When the radio is transmiting, turn MIG inner shaft to adjust RF gain. Turn it clockwise
to increase gain, anti-clockwise to reduce gain.
Turn the mode switch to choose AM/FM/PA mode.
Turn the band switch to choose A/B/C/D/E/F band.
When Echo function is on, turn Tone inner shaft to adjust echo rebound times. Turn
it clockwise to increase times, anti-clockwise to reduce times.
When Echo function is on, turn Tone outter shaft to adjust echo duration time. Turn it
clockwise to increase time, anti-clockwise to reduce time.
Channel Selection
Turn the channel knob to select desired channel.
Clockwise to increase, anti-clockwise to reduce channel.
HOW TO USE YOUR RADIO
OFF/ON Radio
Turn VOL clockwise to switch on the radio, the radio emit a beep. When the LED1.
displays frequency or channel, the radio is on.
Turn VOL anti-clockwise to switch off the radio, the radio is OFF when hear Ka2.
Ta from the switch.
Volume Control
When the radio is turned on, turn VOL clockwise will increase the volume, turn VOL
anti-clockwise will reduce the volume.
Note: Adjust the volume during communication to get suitable level.
Table des matières
Autres manuels AnyTone Radio
AnyTone
AnyTone AT-D868UV Mode d'emploi
AnyTone
AnyTone 868 Manuel utilisateur
AnyTone
AnyTone AT-5555 Manuel utilisateur
AnyTone
AnyTone D578UV Manuel d'utilisation et d'entretien
AnyTone
AnyTone ARES II Manuel utilisateur
AnyTone
AnyTone Dual Band FM Transceiver Manuel utilisateur
AnyTone
AnyTone METIS Manuel utilisateur
AnyTone
AnyTone 578 Go Box DIY Kit Manuel utilisateur
AnyTone
AnyTone AT-598 Manuel utilisateur
AnyTone
AnyTone AT-310M Manuel utilisateur
AnyTone
AnyTone AT-300M Manuel utilisateur
AnyTone
AnyTone AT- 778UV Manuel utilisateur
AnyTone
AnyTone AT-588 Manuel utilisateur
AnyTone
AnyTone AT-D578UV Manuel utilisateur
AnyTone
AnyTone AT888 Manuel utilisateur
AnyTone
AnyTone AT-398UV Manuel utilisateur
AnyTone
AnyTone SMART Manuel utilisateur
AnyTone
AnyTone AT 778 Manuel utilisateur
AnyTone
AnyTone DORIS Manuel utilisateur
AnyTone
AnyTone AM-580 Manuel utilisateur
