Ansr Audio Scan700 Manuel utilisateur
Scan700 Professional Wireless by Ansr Audio
s
To avoid potential damage from a leaking battery, remove batteries if the transmitters will
not be used for a long period of time.
equipment
sequipment
more on
AW-75
4
AW-75
22. DC OUT: Use this to connect the supplied cable from the receiver to the microphone or
transmitter for charging.
10. RF Level Indicator: 5- segment meter glows to indicate RF signal strength. For this, more is
better. If no signal is indicated, your receiver will mute.
11. AF Level Indicator: 5- segment meter glows to indicate RF signal strength. Will move with
your voice level. Try to keep louder passages from staying in the red.
15. Volume Control: Use rotary control to adjust the receiver output level to match with the input
sensitivity of an audio mixer or an amplifier.
manually.
Scans upward to find the next interference-free channel.
(1/4 inch)
1/4 inch
Effectively limits the operating area of the system to help eliminate outside interference.
The higher the squelch control, the smaller the service area of the system. If you need to adjust this,
set the squelch to minimum (larger area), raise until signal is affected, and then back off to make sure
that the required operating area is covered, but not alot more.
5
AW-71
4. AW-71 Handheld Microphone
1. Grille: Protects the microphone capsule and helps reduce breath sounds and wind noise.
2. LCD Display: Displays channel number and battery power level
3. Power: Press for 4 seconds to power the transmitter on or off.
4. Battery Compartment: Insert two AA dry or rechargeable batteries into the compartment
and make sure that the polarity of batteries is correct.
5. Channel up or down Button:
Press power button for 1 second to
set LCD display flashing. (A)
Press channel △ or ▽ button to
change channel up or down. (B)
6. Battery Cover: Unscrew to expose battery compartment and channel selector.
7. Antenna: Permanently connected, helical antenna.
8. Charging Input: If inserted battery is rechargeable, it can be charged by using the supplied
DC-plug cable connection to DC out on the front of the receiver.
CHANNEL
(A) (B)
CHANNEL
1
2
5
6 4
7 8
3
condenser element is clear
and precise. Rechargeable AA batteries are included, but good quality alkalines may also be used,
just in case someone forgets to recharge the transmitter.
The bodypack transmitter operates in UHF band frequency with
PLL synthesized control. UHF 700 preprogrammed selectable frequencies to avoid interfer-
ence. Various uni-directional electret condenser cartridge options. Use 1.5V x 2 AA size dry or
rechargeable batteries for low operating cost.
1. Power: Press for 4 seconds to power the transmitter on or off.
2. Mini XLR Connector: The included electret lapel microphone is inserted into the connector
on transmitter.
3. Antenna: Permanently connected, helical antenna.
4. LCD Display: Displays channel number and battery
power level
5. Channel ?or ? Button:
Press power button for 1 second to
let LCD display flashing. (A)
Press channel △ or ▽ button to
change channel forward or backward. (B)
6. Mic/Line Selector: The switch sets the audio input either to microphone level or line level.
7. Gain: The rotary control adjusts the input audio level of the transmitter. The gain adjustment
range is 10dB.
8. Mic Unit/cable: Microphone connection
9. Battery Compartment: Insert two AA dry or rechargeable batteries into the compartment and
make sure that the polarity of batteries is correct.
10. Belt Clip: Secures the bodypack, may be worn with the antenna either up or down. Be sure the
bodypack is secured before use.
11. Charging Input: The inserted rechargeable batteries are charged by using the supplied
DC-plug cable connection to DC out on the receiver. Charge time depends on depth of discharge.
(A) (B)
AW-72
WIRELESS
7
LINE MIC
AC/DC
ADAPTER
• Plug the DC 12V 500mA power supply into
the power connector on the back of the
receiver.
• Connect the receiver output to the audio
mixer or amplifier input, using a standard
audio cable with 3-pin XLR connectors or ¼
in. phone plugs. Never use the balanced and
unbalanced audio outputs at the same time!
This may cause signal loss or increased
noise.
• Matching the Mic / Line selector position of
receiver with the audio Mixer before
connecting with Mixer.
For Mic (-20dB)
For Line (0dB)
•
6.1 Connecting the Receiver
AC/DC
ADAPTER
Balanced or unbalanced audio cable
AUDIO MIXER
AMPLIFIERLOUDSPEAKER
SET UP
6. Set Up
.
¼ in.
¼ in.
8
Press the ”SET” button for 2 seconds until
“MUTE” is shown and the LCD display is
flashing, then release the button.
Pressing the △ or ▽ to select the “MANUAL”
mode.
MANUAL MODE
SET UP
• Adjust the channel setting of the transmitter
according to the receiver’s channel setting.
• Select the Channel
Press power button for 1 second to set LCD
display flashing.
Press channel △ or ▽ button to change
channel forward or backward.
CHANNEL
BATT.
CHANNEL
BATT.
CHANNEL
BATT.
9
Press the ”SET” button for 2 seconds until
“MUTE” shows and the LCD display is
flashing, then release the button.
Using the △ or ▽ button to select the
“SCAN” mode.
up
AUTO-SCAN MODE SET UP
4
• Adjust the channel setting of the transmitter
according to the receiver’s channel setting.
• Select the Channel
Press power button for 1 second to let LCD
display flashing.
Press channel △ or ▽ button to change
channel forward or backward.
CHANNEL
BATT.
CHANNEL
BATT.
CHANNEL
BATT.
you
next
Ce manuel convient aux modèles suivants
3
Manuels Système de microphone populaires d'autres marques
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur
Alpha Technologies
Alpha Technologies RBMS Manuel utilisateur
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur
Shure
Shure UA844 Manuel utilisateur
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur
Pyle
Pyle PDWM5000 Manuel utilisateur