Anritsu MT8220A Manuel utilisateur

UMTS Master™

Model MT8220A

High Performance Node B Analyzer

MAINTENANCE MANUAL

P/N: 10580-00127

REVISION: C

PRINTED: February 2008

490 JARVIS DRIVE

MORGAN HILL, CA 95037-2809

UMTS Master MT8220A MM i

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

3. Recommended Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4. Performance Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Spectrum Analyzer Frequency Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Spectrum Analyzer Internal Reference Frequency Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 4

Spectrum Analyzer SSB Phase Noise Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Spectrum Analyzer Spurious Response (Second Harmonic Distortion) . . . . . . . . . . . . . . . . . 6

Spectrum Analyzer Residual Spurious Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Spectrum Analyzer Displayed Average Noise Level (DANL) . . . . . . . . . . . . . . . . . . . . . . . . . 9

Input Related Spurious (IRS) Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Spectrum Analyzer Resolution Bandwidth Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Spectrum Analyzer Measurement Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

GPS Option Verification (Option 31) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

GSM/GPRS/EDGE Signal Analyzer Option Verification (Options 40 and/or 41) . . . . . . . . 19

GSM Burst Power, Frequency Error and Phase Error Tests . . . . . . . . . . . . . . . . . . . . . . . . . . 19

EDGE Burst Power, Frequency Error and Residual Error Tests . . . . . . . . . . . . . . . . . . . . . . 21

WCDMA/HSDPA RF Measurements (Option 44) Verification . . . . . . . . . . . . . . . . . . . . . . 22

Error Vector Magnitude (EVM) Verification (Options 45 or 65) . . . . . . . . . . . . . . . . . . . . . 29

5. Battery Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6. Battery Pack Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

7. Opening the UMTS Master Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

8. Real Time Clock (RTC) Battery Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

9. Main PCB Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

10. Spectrum Analyzer Module Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

11. LCD Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

12. LCD Backlight PCB Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

13. Keypad Membrane and PCB Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

14. Function Key Membrane and Switchpad Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

15. Accessories and Replaceable Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

16. ANRITSU Customer Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Appendix A Test Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Test Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

UMTS Master MT8220A MM 1

1. Introduction

This manual provides maintenance instructions for the UMTS Master Model MT8220A Spectrum Analyzer and W-

CDMA Tester. It describes the product and provides performance verification procedures, parts replacement procedures,

and a replaceable parts list.

2. Description

The MT8220A is a synthesizer-based handheld spectrum analyzer and W-CDMA tester.

3. Recommended Test Equipment

The following test equipment is recommended for use in testing and maintaining the UMTS Master.

Table 1. Recommended Test Equipment for Spectrum Analyzer Verification

Equipment Critical Specification Recommended Manufacturer/Model

Synthesizer Frequency: 0.1 Hz to 20 GHz

Power Output to +13 dBm Anritsu Model MG3692A or B with options

2A, 4, 22, 15 *

Power Meter Power Range: –70 to +20 dBm Anritsu Dual Channel Model ML2438A

Power Sensor Frequency: 10 MHz to 18 GHz,

–67 to +20 dB Anritsu Model MA2442D Quantity: 2

Frequency Reference Frequency: 10 MHz Symmetricom Model RubiSource T&M

Fixed Attenuator 10 dB Attenuation Aeroflex/Weinschel Model 1-10 Quantity: 2

Power Splitter Frequency: DC to 18 GHz Aeroflex/Weinschel Model 1870A

50 MHz Lowpass Filter Anritsu Model 1030-96

Adapter Frequency: DC to 20 GHz

N(m)-N(m), 50 Ohm Anritsu Model 34NN50A

Adapter Frequency: DC to 20 GHz

K(m)-N(f), 50 Ohm Anritsu Model 34RKNF50

50 Ohm Termination Frequency: DC to 18 GHz Anritsu Model 28N50-2

RF Coaxial Cable Frequency: DC to 18 GHz

N(m)-N(f), 50 Ohm Anritsu Model 15NNF50-1.5B

Coaxial Cable BNC Male to Male 50 Ohm Any

* Note that MG3692A models require option 15 to achieve power of +13 dBm. MG3692B models do not require option 15 to achieve

+13 dBm power.

2 UMTS Master MT8220A MM

Table 2. Recommended Test Equipment for Options Verification

Equipment Critical Specification Recommended Manufacturer/Model

Synthesizer Frequency: 0.1 Hz to 20 GHz

Power Output to +13 dBm Anritsu Model MG3692A or B with options

2A, 4, 22, 15 *

Vector Signal Generator Frequency: 100 kHz to 3 GHz Anritsu Model MG3700A with Options

MG3700A-002, MG3700A-021 **

Power Meter Power Range: –70 to +20 dBm Anritsu Dual Channel Model ML2438A

Power Sensor Frequency: 10 MHz to 18 GHz,

–60 to +20 dB Anritsu Model MA2482D with Option 1,

Quantity 2

Programmable Attenuator Frequency: DC to 2 GHz

Attenuation:

100 dB (in 1 and 10 dB step)

Anritsu Model MN63A

Fixed Attenuator Frequency Range: DC to 18 GHz

10 dB Attenuation Aeroflex/Weinschel Model 44-10.

Quantity 2

Power Splitter Frequency: DC to 18 GHz Aeroflex/Weinschel Model 1870A

RF Power Amplifier Frequency: 100 to 1000 MHz,

Gain: 35 dB min. Model TIA-1000-1R8

Two BNC(m) to N(f) adapters are required

Adapter Frequency: DC to 20 GHz

N(m)-N(m), 50 Ohm Maury Microwave Model 8828B

Quantity 2 (one if Anritsu Coupler and

Circulator are used)

Adapter Frequency: DC to 20 GHz

K(m)-N(f), 50 Ohm Anritsu Model 34RKNF50

Adapter Frequency: 881.5 MHz

BNC(m) to N(f), 50 Ohm Midwest Microwave Model ADT-2615-NF-

BNM-02, Quantity 2

Adapter Frequency: 881.5 MHz

SMA(m) to N(f), 50 Ohm Midwest Microwave Model ADT-2582-NF-

SMM-02, Quantity 4 (Required only if

Anritsu Coupler and Circulator are used.)

Adapter Frequency: 881.5 MHz

SMA(m) to SMA(m), 50 Ohm Midwest Microwave Model ADT-2594-MM-

SMA-02, (Required only if Anritsu Coupler

and Circulator are used.)

50 Ohm Termination Frequency: DC to 18 GHz Anritsu Model 28N50-2

High Power Load DC to 18 GHz, 10W Aeroflex/Weinschel Model M1418

Coupler Frequency: 881.5 MHz

Coupling Factor: 30 dB Midwest Microwave Model CPW-5140-30-

NNN-05 or CPW-5141-30-NNN-05

Alternative: Anritsu 1091-307 (Two

SMA(m) to N(f) adapters required.)

Circulator Frequency Range: 800 to 1000 MHz

Isolation: 20 dB min Meca Electronics, Inc. part number CN-

0.900

Alternative: Anritsu part number 1000-50

(Two SMA(m) to N(f) adapter and one

SMA(m) to SMA(m) adapter required.)

Coaxial Cable BNC Male to Male 50 Ohm Any

RF Coaxial Cable Frequency: DC to 18 GHz

N(m)-N(m), 50 Ohm Anritsu Model 15NN50-1.5B Quantity 3

GPS Antenna Magnet-mount with 15 foot cable Anritsu Model 2000-1410

* Note that MG3692A models require option 15 to achieve power of +13 dBm. MG3692B models do not require option 15 to achieve

+13 dBm power.

** Note that the MG3700A requires several factory custom test pattern files installed into its memory.

UMTS Master MT8220A MM 3

4. Performance Verification

The sections that are listed below contain tests that can be used to verify the performance of the UMTS Master Model

MT8220A.

A sample performance verification test record is provided on page 47.

Spectrum Analyzer Frequency Accuracy

The following test can be used to verify the CW frequency accuracy of the UMTS Master Spectrum Analyzer.

Procedure:

1. Connect the 10 MHz reference source to the Anritsu MG3692A Synthesized Signal Source. Do not connect the

10 MHz external reference to the MT8220A.

2. Connect the output of the source to the RF Input of the UMTS Master.

3. Connect the external power supply (Anritsu part number 40-168) to the UMTS Master.

4. Press and hold the On/Off key to turn on the UMTS Master.

5. Press the Shift key, the Preset key (1), and then the Preset soft key to reset the instrument to the default start-

ing conditions.

6. Turn on the 10 MHz Reference Standard and the Anritsu MG3692A Synthesized Signal Source.

7. Set the MG3692A output to 1 GHz CW, with an RF output level of –30 dBm.

8. Press the Amplitude key, then press the Reference Level soft key.

9. Use the keypad to enter –10 and select the dBm soft key.

10. Press the Freq key and select the Center Freq soft key.

11. Use the keypad to enter 1and select the GHz soft key.

12. Press the Span key, use the keypad to enter 10, and select the kHz soft key.

13. Press the BW key and select the RBW soft key.

14. Use the keypad to enter 100 and select the Hz soft key.

15. Press the VBW soft key and use the keypad to enter 30, then select the Hz soft key.

16. Press the Marker key, and select the Peak Search soft key.

17. Verify that the marker frequency is 1 GHz, ±1 kHz and record in the test records on page 48, Spectrum Analyzer

Frequency Accuracy.

18. Repeat Steps 7 through 16 for 7 GHz.

19. Verify that the marker frequency is 7 GHz ±7 kHz and record in the test records on page 48, Spectrum Analyzer

Frequency Accuracy.

NOTE: Before continuing, allow a 30-minute warm up for the internal circuitry to stabilize.

NOTE: If the unit fails the Spectrum Analyzer Frequency Accuracy test, perform the Spectrum Analyzer Internal

Reference Frequency Adjustment procedure page 4. If the unit still fails the Frequency Accuracy test after the

Internal Reference Frequency adjustment has been completed, replace the PCB assembly.

4 UMTS Master MT8220A MM

Spectrum Analyzer Internal Reference Frequency Adjustment

Use this procedure to adjust the frequency if the unit fails the Spectrum Analyzer Frequency Accuracy verification test

on page 3.

Procedure:

1. Connect the 10 MHz reference source to the Anritsu MG3692A Synthesized Signal Source.

2. Connect the output of the source to the RF Input of the UMTS Master.

3. Connect the external power supply (Anritsu part number 40-168) to the UMTS Master.

4. Press the On/Off key to turn on the UMTS Master.

5. Press the Shift key, the Preset key (1), and then the Preset soft key to reset the instrument to the default start-

ing conditions.

6. Turn on the 10 MHz reference source and the Anritsu MG3692A Synthesized Signal Source.

7. Set the MG3692A output to 7 GHz with an RF output level of –30 dBm.

8. Press the Amplitude key, then press the Reference Level soft key.

9. Use the keypad to enter –10 and select the dBm soft key.

10. Press the Atten Lvl soft key, use the keypad to enter 0 and press the dB soft key.

11. Press the Freq key and select the Center Freq soft key.

12. Use the keypad to enter 7 and select the GHz soft key.

13. Press the Span key, use the keypad to enter 10, and select the kHz soft key.

14. Press the BW key and select the RBW soft key.

15. Use the keypad to enter 100 and select the Hz soft key.

16. Press the VBW soft key and use the keypad to enter 30, then select the Hz soft key.

17. Press and hold the Shift key and press the 4, 6, and 8(from top) soft keys together to enter into the UMTS Mas-

ter Service Mode (Figure 1).

18. Press the Service Menu soft key, then the APP Service soft key.

19. Press the Calibration soft key, then the 10 MHz TXCO soft key.

20. Use the Up/Down arrow keys or the rotary knob to slowly adjust the displayed signal to the center of the dis-

play. Allow the signal to stabilize between adjustments, and repeat as necessary.

21. Turn the UMTS Master off, and then back on to exit Service Mode.

NOTE: Before continuing, allow a 30-minute warm up for the internal circuitry to stabilize.

Figure 1. MT8220A UMTS Master Service Key Sequence

UMTS Master MT8220A MM 5

Spectrum Analyzer SSB Phase Noise Verification

This test can be used to verify the single side band phase noise of the UMTS Master.

Procedure:

1. Connect the 10 MHz reference source to the Anritsu MG3692A Synthesized Signal Source.

2. Connect the output of the MG3692A Synthesized Signal Source to the RF In connector of the UMTS Master.

3. Connect the external power supply (Anritsu part number 40-168) to the UMTS Master.

4. Press the On/Off key to turn on the UMTS Master.

5. Press the Shift key, the Preset key (1), and then the Preset soft key to reset to the default starting conditions.

6. Turn on the 10 MHz reference source and the Anritsu MG3692A Synthesized Signal Source.

7. Set the MG3692A output to 7.09 GHz CW, with an RF output level of +13 dBm.

8. Press the Amplitude key, then press the Reference Level soft key.

9. Use the keypad to enter 0 and select the dBm soft key.

10. Press the Atten Lvl soft key, use the keypad to enter 15 and press the dB soft key.

11. Press the Freq key and select the Center Freq soft key.

12. Use the keypad to enter 7.090050 and press the GHz soft key.

13. Press the Span key, use the keypad to enter 110, and select the kHz soft key.

14. Press the BW key and select the RBW soft key.

15. Use the keypad to enter 1 and select the kHz soft key.

16. Press the VBW soft key and use the keypad to enter 3, then select the Hz soft key.

17. Press the Shift key and then press the Trace (5) key.

18. Press the # of Average soft key, use the keypad to enter 7, then press the Enter key.

19. Wait until the Trace Count indicator on the left side of the display shows 7/7.

20. Press the Marker key and select the Peak Search soft key.

21. Press the Delta On/Off soft key to turn Delta on.

22. Use the keypad to enter 10 and press the kHz soft key.

23. Subtract 30 from the dB value shown on the marker readout to convert the value to dBc/Hz (for example, if the

marker reads -80 dB, the value becomes -110 dBc/Hz). Record the dBc/Hz value in the test records in Appen-

dix A, Spectrum Analyzer SSB Phase Noise Verification.

24. Repeat Steps 22 and 23 for 20 kHz marker delta, 30 kHz marker delta and 100 kHz marker delta.

NOTE: Before continuing, allow a 30-minute warm up for the internal circuitry to stabilize.

6 UMTS Master MT8220A MM

Spectrum Analyzer Spurious Response (Second Harmonic Distortion)

The following test can be used to verify the input related spurious response of the UMTS Master.

Procedure:

1. Connect the 10 MHz reference source to the Anritsu MG3692A Synthesized Signal Source.

2. Connect one end of the 50 MHz Low Pass Filter to the output of the source and the other end to the UMTS Mas-

ter RF Input with the coaxial cable.

3. Connect the external power supply (Anritsu part number 40-168) to the UMTS Master.

4. Press the On/Off key to turn on the UMTS Master.

5. Press the Shift key, the Preset key (1), and then the Preset soft key to reset the instrument to the default start-

ing conditions.

6. Turn on the 10 MHz reference source and the Anritsu MG3692A Synthesized Signal Source.

7. Set the MG3692A output to 50.1 MHz CW, with an RF output level of –30 dBm.

8. Press the Amplitude key, then press the Reference Level soft key.

9. Use the keypad to enter –27 and press the dBm soft key.

10. Press the Atten Lvl soft key and enter 0, then press the dB soft key.

11. Press the Span key, use the keypad to enter 100, and select the kHz soft key.

12. Press the Shift key and then press the Trace (5) key.

13. Press the Detection soft key, and then the Peak soft key.

14. Press the BW key and select the RBW soft key.

15. Use the keypad to enter 1 and select the kHz soft key.

16. Press the VBW soft key and use the keypad to enter 10, then select the Hz soft key.

17. Press the Freq key and select the Center Freq soft key.

18. Use the keypad to enter 50.0 and press the MHz soft key.

19. Press the Shift key and then press the Trace (5) key.

20. Press the # of Average soft key, use the keypad to enter 5, then press the Enter key.

21. Wait until the Trace Count displays 5/5.

22. Press the Marker key and select the Peak Search soft key.

23. Record the amplitude for 50.1 MHz in the test records on page 48, Spectrum Analyzer Spurious Response (Sec-

ond Harmonic Distortion).

24. Press the Freq key and select the Center Freq soft key.

25. Use the keypad to enter 100.2 and press the MHz soft key.

26. Press the Shift key and then press the Trace (5) key.

27. Press the # of Average soft key, use the keypad to enter 5, then press the Enter key.

28. Wait until the Trace Count displays 5/5.

29. Press the Marker key and select the Peak Search soft key.

30. Record the amplitude for 100.2 MHz in the test records on page 48, Spectrum Analyzer Spurious Response

(Second Harmonic Distortion).

31. Calculate the Second Harmonic Level in dBc using the following formula:

Second Harmonic Level (dBc) = Amplitude @ 100.2 MHz - Amplitude @ 50.1 MHz

32. Record the calculated dBc value in the "2nd Harmonic Distortion" box in the test record and verify that it is -50

dBc or better.

NOTE: Before continuing, allow a 30-minute warm up for the internal circuitry to stabilize.

Table des matières

Autres manuels Anritsu Instrument de mesure

Anritsu

Anritsu IQproducer XG-PHS Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Anritsu

Anritsu MP1763C Manuel utilisateur

Anritsu

Anritsu AM-9000 Series Manuel utilisateur

Anritsu

Anritsu MS2711B Manuel utilisateur

Anritsu

Anritsu Field Master Pro MS2090A Manuel utilisateur

Anritsu

Anritsu Field Master Pro Manuel utilisateur

Anritsu

Anritsu MP1570A Manuel utilisateur

Anritsu

Anritsu MS9740A Manuel utilisateur

Anritsu

Anritsu IQ Fiber Master MT2780A Manuel utilisateur

Anritsu

Anritsu S331E Manuel utilisateur

Anritsu

Anritsu MT8212E Manuel utilisateur

Anritsu

Anritsu MS2830A Manuel utilisateur

Anritsu

Anritsu BTS Master MT8220T Manuel utilisateur

Anritsu

Anritsu MP1900A Series Manuel utilisateur

Anritsu

Anritsu Spectrum Master MS2721B Manuel utilisateur

Anritsu

Anritsu PIM Master MW8208A Manuel utilisateur

Anritsu

Anritsu ML2400A Series Manuel utilisateur

Anritsu

Anritsu MS2690A Manuel d'installation

Anritsu

Anritsu MP1595A Manuel utilisateur

Anritsu

Anritsu Site Master S810D Manuel utilisateur

Anritsu

Anritsu 11 Series Mode d'emploi

Anritsu

Anritsu Spectrum Master MS2721B Manuel du propriétaire

Anritsu

Anritsu MS2711B Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur