Anderson RB600 Guide de dépannage

This Quick start up guide does not replace in any way or form the

user manual of this unit.The intension of this document is for use

when setting up the machine after delivery to the dealer and before

the machine is transferred to the end user.This document should

be used as achecklist and memory aid for employees already

familiar with the guidelines in the user manual.Failure to operate

the product correctly can result in damage to the product, personal

property, and cause serious injury.This guide should not be

transferred to the owner of the machine.

QUICK START UP

RB600

After receiving your machine you will want to set it up to be ready for any demo

opportunity or sale that may come along.Besides that, you want to be sure that the

machine is in factory condition, free of damage from transport and defective parts due

to the transport from our factory to your dealership.This is aquick guide that will help

you to be up and ready in ashort time.Before using the machine you must grease and

oil all points on the wrapper that require it.

Basics:

Round bale wrapper

•4 or 5ft bale

•1 stretcher (30’’)

•Computer & remote

•Mechanical plastic cut and hold

Note: Before pressure washing the machine be sure to remove the computer

QUICK START GUIDE

RB600

QUICK START GUIDE

RB600

When the machine is to be delivered to the user there are steps you must follow to be sure they are

comfortable with wrapping their first bale. These steps are also important if you are doing a live demo.

Setup is very important to bale size as this machine is not set to a specific bale at the factory.

1) Know your bale size before you start. Asking can help but an actual measurement of

the bale is sometimes necessary.

2) Be sure that everything is greased (if left for more than 3 months outside without use

the machine needs to be fully greased and oiled.

3) Your remote control is charged and tested operational (see user manual on machine for

functions).

The stretcher pole has 3 positions. Be sure that the position is

not over the height of the bale or under it. (This part is normally

removed for shipping so be sure to install it correctly to wrap

your bales)

Set the cone rollers for 4 or 5 foot

long bale.

Put plastic in the

stretcher. There is only

one way to put the plastic

through. See the diagram

to the left. This is a

sticker found on the

machine as well.

Turn on the computer.

1) Pull the emergency stop button (1), the blue

light (2) will come on.

2) Press the power button on the remote (3),

when the screen is ON push the power button

(3) again

3) Make sure the M.C. LED light (4) on the

receiver’s control panel is ON.

QUICK START GUIDE

RB600

Hook the machine up to atractor to test it.

Attach the machine’s hoses to the tractor as

shown.Be sure that your tractor is adjusted

at aflow rate of 8GPM at 2000 PSI.

Or, if equipped with aHonda power unit,

make sure it is full of gas and oil.

Starting and Aligning the wrapper

1) If equipped with an Honda engine, put the

ignition key in the ON position and press the

start engine button on the remote.

2) Before wrapping you need to align the

wrapper, press the alignment key (5) on the

remote control.

3) When the alignment menu appears on the

remote control screen, press the same key (5)

asecond time, the alignment will start and the

screen should display Alignment in progress (it

can take up to 2minutes).

Receiver

Remote

Emergency control box

Start Wrapping

1) Make sure the blue button’s light (2) is on,

which means that the alignment is finished.

2) Push the wrap key (6), the wrapper’s table will

make the set number of rotation and

unloading will happen automatically, and will

engage the plastic cutter.

3) If the remote is not charged or missing you can

wrap automatically by pressing the blue

button (2).

QUICK START GUIDE

RB600

The RB500 is equipped with amechanical cut and hold system.The mechanical cut and

hold works on arack and pinion system that stretches alarge spring as the table turns.

The trigger for the release of the system is under the table and is activated as the table

dumps.If the plastic isn’t cut or not completely cut you want to make sure the blade is

sharp and free of rust first.Then you can check if the trigger hits the plate at the right

time and adjust it if need be.

Activated too early Activated at the right time

Fine tuning adjustment

Basic adjustment

Activation plate

Table des matières

Autres manuels Anderson Matériel agricole

Anderson

Anderson WRAPTOR Manuel utilisateur

Anderson

Anderson IFX720 Manuel

Anderson

Anderson RB-400 Manuel utilisateur

Anderson

Anderson RB-400 Manuel utilisateur

Anderson

Anderson RB580 Manuel utilisateur

Anderson

Anderson RB-200 Manuel utilisateur

Anderson

Anderson RB-200 Manuel utilisateur

Anderson

Anderson 680HS Manuel utilisateur

Anderson

Anderson RB-500 Manuel de l'opérateur

Anderson

Anderson 680HS Manuel utilisateur

Anderson

Anderson RB580 Manuel utilisateur

Anderson

Anderson RBM1400 Manuel utilisateur

Anderson

Anderson TRB1000 Guide de configuration

Anderson

Anderson RB-200 Manuel utilisateur

Anderson

Anderson RB580 Manuel utilisateur

Anderson

Anderson NutriWrap 780 SB Manuel utilisateur

Anderson

Anderson GB series Manuel utilisateur

Anderson

Anderson TSR-3450 Manuel utilisateur

Anderson

Anderson Fusion720 Manuel utilisateur

Anderson

Anderson Fusion720 Manuel utilisateur

Anderson

Anderson TRB-2000 Manuel utilisateur

Anderson

Anderson RB 680 Manuel utilisateur

Anderson

Anderson Double stretcher Manuel utilisateur

Anderson

Anderson NWS-660 Manuel utilisateur

Manuels Matériel agricole populaires d'autres marques

GSi

GSi PNEG-2314 Manuel utilisateur

Checchi & Magli

Checchi & Magli TEXDRIVE Manuel utilisateur

Amazone

Amazone Cenius 4003-2TX Manuel utilisateur

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manuel utilisateur

Cima

Cima BLITZ Instructions d'utilisation et d'entretien

Amazone

Amazone CombiDisc 3000 Instructions d'installation

HE-VA

HE-VA Disc-Roller XL Contour Manuel utilisateur

AGT

AGT AGT-SSFM Manuel utilisateur

Milestone

Milestone 72-84 Manuel utilisateur

KUHN

KUHN Hector 3000 Manuel utilisateur

Krone

Krone X-Disc 6200 Manuel utilisateur

Eliet

Eliet DZC450 Manuel utilisateur

Taarup

Taarup BIO+ B4000 Manuel utilisateur

Garland

Garland SHAKER 310 DPG Manuel utilisateur

stable comfort

stable comfort StableWall System Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

International

International 710 Manuel utilisateur

Ashland

Ashland HDW-3217-14 Manuel utilisateur