Ancona 450 CFM Manuel utilisateur

Table des matières

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur

IMPORTANT SAFETY INSTRUCTIONS

Carefully read the following important information regarding

installation safety and maintenance.

Keep these instructions for future reference.

RANGE HOOD

USER INSTRUCTIONS

MODEL:

Wall Mount

Pyramid Rim 450 CFM

30 Inches

2016-01-20 MAAN1106-01

2

Manual Push Button

Push the ‘Stop’ button, and the motor will stop.

Push the ‘Low’ button and the motor runs at low speed.

Push the ‘Mid’ button and the motor runs at mid speed.

Push the ‘High’ button and the motor runs at high

speed.

Push the ‘Light’ button and lights will come on. Push it

again and the light will turn off.

This range hood requires 2 incandescent lamps.

•

•

•

•

•

3

GENERAL INSTALLATION INSTRUCTIONS

PREPARATION

A: GENERAL

Carefully unpack the hood but do not remove any

protective film until after installation to avoid

accidental damage or scratching. Place filters

somewhere safe for the same reason.

Check for damage, and lay out the hood pieces and

parts.

Range hoods do not come with wall or ceiling screws,

as the type of structure determines the type of screws.

Check that you have the right tools. In addition to

marking and measuring tools, a hammer, screwdrivers,

pliers and scissors, you may need sheet metal sheers,

and wire strippers. Safety glasses are recommended.

B: ELECTRICAL CONNECTION

This range hood must be grounded. If the dwelling

wiring is not 2-wire with a ground wire, a ground must

be provided by the installer.

Install a 5.08 X 10.16 cm (2” X 4”) wall outlet box and

3-blade 125 Volts, 15 amp grounded receptacle.

Use wire nuts to connect incoming ground, neutral and

hot.

Push wires into the junction box and replace cover. Be

sure wires are not pinched.

C- INSTALLATION DISTANCE FROM TOP OF

RANGE

Hood should be placed at a minimum of:

–61 cm (24”) for electric cooking surface

–

76 cm (30”) for gas cooking surface

4

WALL MOUNTED RANGE HOOD INSTALLATION

Wall Mounted range hoods can be ducted outside (exhaust

mode) or vented internally (recirculation mode)

DUCTED EXHAUST MODE INSTALLATION (Pic 7a &7b)

In exhaust mode hood models, the kitchen vapors are purified by

the metal anti-grease filters and carried outside through a ducting

system.

To begin, choose where the ductwork should run between the hood

and the outside of your home. The straighter and shorter the duct

run, the more efficient the performance.

RECIRCULATING MODE INSTALLATION (Pic 8)

Recirculation kits are available for the Rapido II models.

The kitchen vapors are purified by the metal anti-grease filters and

an activated carbon filter, then conveyed back into the kitchen.

In order to transform your cooker hood from the exhaust version to

the recirculation version, you need to purchase a recirculation kit

separately and then carry out the installation instructions enclosed

with the kit.

TO REDUCE THE RISK OF FIRE, USE ONLY METAL

DUCTWORK.

Note: Range hoods pictured in this manual are generic to

represent all models.

Pic 7a

Pic 7b

Pic 8

.

RECIRCULATING MODE INSTALLATION (Pic 8)

5

WALL MOUNTED STAINLESS STEEL RANGE HOOD

INSTALLATION

Make the holes that correspond with the centre of the cooktop, so that the

lower part of the hood, which is to be assembled afterwards, is arranged at

least 61 cm (24”) from the stove top for electric models and at least 76 cm

(30”) for gas models. (See Pic 9)

Installing range hood hook: Drill 3 holes in a suitable place according to

size of hook, use screws to fix the hook on the wall.

Installing chimney bracket: drill 2 holes according to size of inside chimney

bracket in a suitable position, the position of bracket should be flush with the

top of the outside chimney. (See Pic 10)

Fix the damper on the top vent of hood with 4 screws (See Pic 4), then

install the ducting pipes onto the damper. (See Pic 11) - If the ventilation

system is equipped with an external air duct with a different diameter, apply

a reduction fitting. However for maximum performance and safety 6” Ø

ducting is recommended.

Use 2 screws to fix two chimneys together with the outside chimney bracket,

make sure inside chimney is moving freely. (See Pic 12)

Install the chimneys on the hood. (See Pic 13)

Fix the chimney and hood together with two screws. (See Pic 14) –This step

is just for the models which have holes on bottom of outside chimney.

Hang the hood on the range hood hook. (See Pic 15)

Pull out the inside chimney and adjust height according to the position of

inside chimney bracket on the wall, then fix the inside chimney on the

bracket with two screws. (See Pic 16)

6