AnaJet mP5i Manuel utilisateur
Service Manual
Version 1.1
User Manual
Copyright © 2014 Anajet LLC
Table of Contents
Cover ........................................................................................... 3
Chapter 1: Introduction ............................................................. 4
Capter 2: Adjustments .............................................................. 5
2.1 Carriage Belt Tension ...................................................................... 5
2.2 Table Belt Tension ............................................................................ 6
2.3 Table Motor Belt Tension Adjustment .......................................... 7
2.4 Carriage Encoder Adjustment ..................................................... 12
2.5 Wiper Height Adjustment ................................................................ 13
2.6 Table Z Axis Motor Limit Flag Adjustment ................................. 16
2.7 Obstruction Laser Sensor Adjustment ...................................... 20
2.8 Lubrication ....................................................................................... 26
2.8.1 Linear Guide Rail -Table ........................................................................................... 26
2.8.2 Linear Guide Rail - Carriage .................................................................................... 27
Chapter 3: Parts Replacement ................................................. 29
3.1 Damper Replacement ..................................................................... 30
3.2 Ink supply tube replacement ......................................................... 40
3.2.1 Removing Ink tubees ................................................................................................. 40
3.2.2 Replacing Ink tube system ........................................................................................ 47
3.3 Maintenance Station Replacement ............................................. 59
3.3.1 Maintenance Station Pump Replacement ............................................................... 62
3.3.2 Maintenance Station Wiper Assembly Replacement ........................................... 64
3.4 Ricoh Gen 4 Print Head Controller Replacement ...................... 66
3.5 Print head Replacement ................................................................ 68
3.6 Ricoh Carriage Controller Board Replacement ........................ 70
3.7 Ink Bay Assemblies ........................................................................ 72
3.7.1 Needle Plate-Pin Shift Assembly Replacement ..................................................... 72
3.7.2 Ink Needle Replacement (CMYK) ............................................................................ 76
3.8 Ink Slot Controller Board Replacement ..................................... 79
3.9 USB-ETH-CAN Switch Board Replacement ................................ 81
3.10 Table Motion Control Board Replacement ............................... 83
3.11 Carriage Motion Control Board Replacement ........................ 84
3.12 Power Supply Replacement ....................................................... 85
3.13 Control Panel Assembly Replacement ..................................... 87
3.13.1 Control Panel O-MAP Board Replacement ......................................................... 89
3.13.2 Control Panel I-O Board Replacement .................................................................. 90
3.13.3 Replacing LCD Screen ........................................................................................... 91
3.14 Button Assembly Replacement ................................................................................ 92
Part # ..................................................................................................................................... 94
Anajet mPower i-Series ServiceManual
2
Cover
mPower™Service Manual
Version 1.1
Copyright © 2014 AnaJet LLC. All rights reserved. Reproduction or repurposing of any of the contents is prohibited.
Anajet mPower i-Series ServiceManual
3
Chapter 1: Introduction
This manual is to be used in conjunction with Anajet mP5i & mP10i Printer User Manual. All
operational instructions, normal printer maintenance and troubleshooting guides can be found in
the User manual. This Service manual is intended to aid Anajet distributor's, technical and service
personnel in providing maintenance and basic repair service to there customers. The services
provided by distributor's service personnel are intended to be limited to the diagnosis, often with
the help of Anajet's Technical Support personnel, simple adjustments, and replacement of printer
circuit boards. Accordingly this service manual is limited to meet the objectives indicated above.
The majority of the hardware used in the Anajet mP5i & mP10i printer is english inch series.
There are however a few metric sized fasteners and care must be exercised when reassembling
hardware to insure the correct sizes are installed.
Anajet mPower i-Series ServiceManual
4
Capter 2: Adjustments
2.1 Carriage Belt Tension
Tools Needed
o7/16 Ratchet Wrench
oGates Belt Tension Meter or equivalent
1. Loosen the two hex head bolts using a 7/16 ratchet wrench. The two hex bolts will be located on the far
right underneath the belt pulley. See photo 2.1-1.
Photo 2.1-1
2. You can now adjust the belt tension by tightening or loosening the nut on the threaded rod. Use a 7/16
ratchet wrench to loosen and tighten the belt. See Photo 2.1-2
Photo 2.1-2
3. Once you have adjusted the tension, check the belt using a Gates belt tension meter or equivalent. Below
Anajet mPower i-Series ServiceManual
5
are the belt specifications needed for the meter.
Mass (M) - 001.4 g/mm
With (W) - 009.0 mm/r
Span (S) - 0800 mm
The belt tension should be set to 23.5 to 25.5 N (84.5 - 91 ozf). Measurements should be made on the rear
portion of the belt with the carriage positioned at either end of the travel. Once we reached the desired tension
we can retighten the two hex bolts under the pulley to lock it in place.
2.2 Table Belt Tension
Tools Needed
oPhillips Screw Driver
o11/32 Ratchet Wrench
o10/32 Allen Key / T-handle
oGates Belt Tension Meter or equivalent
1. Move the table to the home position by pressing the TABLE button (table should be inside the printer).
Remove the three Phillips screws from the bottom of the skirt and remove the skirt. See Photo 2.2-1
Photo 2.2-1
2. Remove the Two 10-32 screws (use a 11/32 ratchet wrench) and two 8-32 nuts (use 10/32 Allen
key / T handle) from the pleated screen mount and slide the pleated screen back to reveal the table belt
tensionor. See Photo 2.2-2
Anajet mPower i-Series ServiceManual
6
Photo 2.2-2
3. Loosen the table belt bracket nuts(use a 3/8 ratchet wrench). See photo 2.2-3. Adjust the belt tension by
tightening or loosening the adjustment nut on the threaded rod (use a 7/16 ratchet wrench). See Photo 2.2-3
Photo 2.2-3
4. Check the belt tension using a Gates belt tension meter or equivalent. Below are the belt specifications
needed for the tension meter.
Mass (M) - 001.4 g/m
With (W) - 009.0 mm/r
Span (S) - 0790 mm
Belt tension should be set to 25 to 30 N (90 to 108 ozf). Measurements should be made on the middle portion
of the belt with the table at the home position.
5. Once we reached the desired tension, we can now tighten the table bracket nuts and reassemble the
pleated screen mount and skirt by reversing the above steps.
2.3 Table Motor Belt Tension Adjustment
Tools Needed
o3/8th ratchet wrench
Anajet mPower i-Series ServiceManual
7
oGates Tension Meter
o3/32 Phillips screw driver
o7/16 ratchet wrench
1. The best way to adjust the tension in the Table motor belt is to remove the entire table guide assembly
from the printer. Before starting power down the printer. To remove the table guide assembly, we must first
unplug the cables connected to the table board. See photo 2.3-1 below
Photo 2.3-1
2. Once the cables have been unplugged from the table board we can now start removing the 8 hex screws
holding the table guide assembly in place. Use a 3/8 ratchet wrench to remove the 8 screws see Photo 2.3.2
and Photo 2.3.3 below.
Anajet mPower i-Series ServiceManual
8
Photo 2.3-2 Photo 2.3-3
You will now be able to remove the entire table guide assembly. We recommended using 2 people to remove
the assembly from the printer and place it on a separate table. Your printer should now look like this see
Photo 2.3.4 below.
Photo 2.3.4
3. To adjust the tension on the Motor belt we must first loosen the Table Belt. Begin by removing the 3
Phillips screws located underneath the table assembly. See Photo 2.3.5. When the 3 Phillips screws are
removed you can now remove the front table cover.
Anajet mPower i-Series ServiceManual
9
Photo 2.3.5
4. Remove the Two 10-32 screws (use a 11/32 ratchet wrench) and two 8-32 nuts (use 10/32 Allen key / T
handle) from the pleated screen mount and slide the pleated screen back to reveal the table belt tensionor.
See Photo 2.3.6 below.
Photo 2.3.6
3. Loosen the table belt bracket nuts(use a 3/8 ratchet wrench). Loosening the adjustment nut on the
threaded rod (use a 7/16 ratchet wrench). See Photo 2.3.7
Anajet mPower i-Series ServiceManual
10
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels AnaJet Imprimante
