AMTIFO A6 Manuel utilisateur
1. Useful accessories:
Thank you for buying our camera. In return for your purchase, we
would like to offer you a useful accessory.
2. Certificate:
This system was certified by: CE & FCC & EMC & RoHs &
Waterproof
3. Package Includes:
•Wireless License Plate Camera
•5 inch Monitor
•Power Cords (2)
•Bracket
•Cigarette lighter adapter
•T-Taps (2)
•Split connector adapter
•Antenna
•Screws
•Instruction manual
4. Working Range:
This system is designed mainly for cars, trucks, campers, SUVs, vans,
and minivans.
Vehicles under 33FT---High-Speed Driving Observation
Vehicles under 40FT---Slow-Speed Driving or Reversing
If your vehicle is too large or you encounter signal issues, please
contact us immediately and we will provide a solution.
5. Before installing, read the information below:
1) Please note the acceptable power supply voltage input to the
monitor and camera.
Monitor: Voltage range 9V-35V
Camera: Voltage range 9V-24V
Note:
1. If the power supply exceeds 24V it will cause the damage to the
camera. We recommend DC 12V to the monitor and camera.
2. If the positive and negative poles are reversed, the camera will be
burnt out
2）Before installation, you must test the device. Please reference the
image below.
A. Plug power cords to the monitor and connect the power wires to
camera (red-red, black-black).
B. Loosen the screws on green adapter, then insert the red wire
(copper wire) to the Positive(+) slot, and the black wire(copper
wire) to the Negative(-) slot.
C. Plug in the cigarette lighter and turn on the red switch. If you see
an image on monitor, it means that the display is functioning
properly.
Tips：
Test to make sure that your surroundings appear/display on the
monitor screen! Once you have confirmed the monitor works, you
are ready to install it.
If there is no image after you have installed the unit, check your
connections to the power source. PLEASE NOTE: if you reverse the
positive wire and negative wire, it will damage the camera so be
cautious. If you cannot verify which wire is positive, connect the
white wire to “ground” it (attach it to a metal part on vehicle) and
then test the positive wire. Grounding it will protect the camera.
6. Attach waterproof antenna
Identify the thin wire that connects to the camera (see below sample
image). This is the waterproof antenna. Since it is waterproof, you
can affix the antenna to the inside or outside of the vehicle and it will
not be affected by water or rain. We recommend attaching it near the
license plate. If your vehicle is quite long, the signal may not be
powerfully enough to reach the monitor so you may have to position
it closer for better transmission.
7. Wires connection
Please pay attention to the positive and negative poles of the wire. If
the positive and negative poles are reversed, it may surge and cause
the monitor to smoke. If the monitor is emitting smoke, please turn
off the power immediately and contact customer support.
(1) The monitor can be powered by a cigarette lighter.
(2) The camera can be powered by one of two methods.
a) If you plan to use the camera only when backing up, power it
by attaching it to the backup/reverse tail-light of your car.
b) If you plan to use the camera continuously (while driving and
reversing), power it by connecting it to the running
light/tail-light (the lights that is on continuously while driving).
If you have questions about this step or the power supplies in
your specific car make/model, email us.
(3) We have also provided an additional power cord that can be
connected to the ACC/Fuse/Radio etc. to power the monitor
Tips：Red wire to positive pole, black wire to ground.
Note :
1. If you supply power to the cigarette lighter, please turn off the
power through the red button of the plug when you are not use the
system. Failure to do so will cause the monitor to drain the battery on
the vehicle.
2. If there is no image after your installing, please check the
connections of power source. Or if you reversed the positive wire and
negative wire, caused the no image. Please be cautious. If you cannot
verify which wire is positive, you can connect the white/Black wire to
ground (metal part on vehicle), then to test and connect the red wire
to one of the back up light wire, if there is image appear on screen,it
means you did correctly.
3. In the light wires of most cars in the US, the red and black wire do
not represent the positive and negative poles. Many times the black
wire of the car lights is the positive pole, and the green or white wire
is the negative pole. please check it before installation. If the wrong
wire is connected and there is no image when connected, it means
that the positive and negative poles are connected reversely. Need to
unplug the power immediately and reconnect correctly. Otherwise it
will burn the camera.
8. Installation Video and Signal Repairing .
See the following link to watch an installation instruction video on
YouTu be: https://youtu.be/NJDAwiPhteI
If the code doesn’t work, you can search the video ID on YouTube:
NJDAw iPhteI or Video name: AMTIFO A6 Wireless Rear View
Camera System Operation Video on www.youtube.com or email us
for help with the link.
II. Signal Pairing
The system signals between the camera and the monitor arrive
already paired. If the signal is good, do not not attempt to pair it
again yourself. If you lose signals or if you change the camera and the
signal needs to be re-paired, read the below.
Pairing Steps:
Step 1 : Make sure the camera and monitor are powered on.
Step 2 : Touch the “Menu'' button of the monitor into menu mode
until “Pair” appears on the monitor, then press the ''+'' button to
pair the signal .
Step 3 : Wait for the image appearing .
9. The camera is made of waterproof material IP69
Waterproof
Table des matières
