Amprobe ACD-14 PLUS Manuel utilisateur
1
MAX 600A
MAX
HOLD
ON
OFF
SELECT
MAX
COM
A
Hz
ACD-14 PLUS
!
!
A
600V CAT III
kM
Hz
℉
℉
©
m
n
%
kM
Hz
℉
©
m
n
%
Features of this instrument
1) Transformer Clamp Jaw for AC current magnetic field pick up
2) Hand/Finger Barrier to indicate the limits of safe access of the meter during
measurement
3) Push-buttons for special functions & features. Also as power ON/OFF buttons
for ACA function in Twin Display Models
4) Push-buttons for special functions & features on Slide-switch Selector functions
5) Input Jack for all functions EXCEPT non-invasive ACA current function
6) Common (Ground reference) Input Jack for all functions
7) Slide-switch Selector to turn the power ON/OFF and Select a function
8) 3-3/4 digits 4000 counts LCD display(s)
9) 3-3/4 digits display for ACA
10) Jaw trigger for opening the transformer clamp jaw
11) Jaw center Indicators, at where best ACA accuracy is specified
12) Jaw marking lines for ACA position error indication
➊
➓
➒
➑
➐
➏➎
➍
➌
➋
2
Limited Warranty and Limitation of Liability
Your Amprobe product will be free from defects in material and workmanship for 1
year from the date of purchase. This warranty does not cover fuses, disposable batteries
or damage from accident, neglect, misuse, alteration, contamination, or abnormal
conditions of operation or handling. Resellers are not authorized to extend any other
warranty on Amprobe’s behalf. To obtain service during the warranty period, return the
product with proof of purchase to an authorized Amprobe Test Tools Service Center or
to an Amprobe dealer or distributor. See Repair Section for details. THIS WARRANTY
IS YOUR ONLY REMEDY. ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED OR
STAUTORY - INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE
OR MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER SHALL NOT BE
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not
allow the exclusion or limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.
Repair
All test tools returned for warranty or non-warranty repair or for calibration should be
accompanied by the following: your name, company’s name, address, telephone number,
and proof of purchase. Additionally, please include a brief description of the problem or
the service requested and include the test leads with the meter. Non-warranty repair or
replacement charges should be remitted in the form of a check, a money order, credit
card with expiration date, or a purchase order made payable to Amprobe® Test Tools.
In-Warranty Repairs and Replacement – All Countries
Please read the warranty statement and check your battery before requesting repair.
During the warranty period any defective test tool can be returned to your Amprobe®
Test Tools distributor for an exchange for the same or like product. Please check the
“Where to Buy” section on www.Amprobe.com for a list of distributors near you.
Additionally, in the United States and Canada In-Warranty repair and replacement units
can also be sent to a Amprobe® Test Tools Service Center (see next page for address).
Non-Warranty Repairs and Replacement – US and Canada
Non-warranty repairs in the United States and Canada should be sent to a Amprobe®
Test Tools Service Center. Call Amprobe® Test Tools or inquire at your point of purchase
for current repair and replacement rates.
3
ACD-14 PLUS & ACD-14 TRMS-PLUS
Clamp-on Multimeter With Dual Display
Contents
Instrument Familiarization ............................................................................................ 1
Warranty and Repair ....................................................................................................... 2
Symbols ............................................................................................................................. 3
Introduction. ..................................................................................................................... 4
Warnings and Precautions ............................................................................................... 4
Unpacking and Inspection ............................................................................................... 5
Operation ......................................................................................................................... 5
Maintenance and Troubleshooting ................................................................................. 9
Battery Replacement. ..................................................................................................... 10
Specications ................................................................................................................. 10
Figures ............................................................................................................................. 15
SYMBOLS
Caution! Refer to the explanation in this Manual
Earth (Ground)
Double Insulation or Reinforced insulation
AC--Alternating Current
DC--Direct Current
Conforms to relevant Australian standards
Underwriters Laboratories Inc. [Note: Canadian and US.]
Complies with European Directives
Application around and removal from hazardous live conductors
is permitted
Do not dispose of this product as unsorted municipal waste
4
Introduction
The ACD-14 PLUS and ACD-14 TRMS-PLUS are digital clampmeters that measure both AC
and DC voltage, AC current, Resistance, Frequency, Continuity and Diode Test. Frequency
can be measured in the voltage and current modes.
WARNINGS AND PRECAUTIONS
Safety Information
• The ACD-14 PLUS Series Digital Clampmeters conform to EN61010-1:2001; EN61010-
2-032:2002; CAT III 600 V, class 2 and pollution deg.2
• This instrument is EN61010-1 certified for Installation Category III (600V). It is recom-
mended for use in distribution level and fixed installations, as well as lesser installa-
tions, and not for primary supply lines, overhead lines and cable systems.
• Do not exceed the maximum overload limits per function (see specifications) nor the
limits marked on the instrument itself. Never apply more than 600 Vdc/600 V ac rms
between the test lead and earth ground.
WARNING
• Before and after hazardous voltage measurements, test the voltage function on a
known source such as line voltage to determine proper meter functioning.
• Disconnect the test leads from the test points before changing meter functions.
• Inspect the Clampmeter, test leads and accessories before every use. Do not use any
damaged part.
• Never ground yourself when taking measurements. Do not touch exposed circuit ele-
ments or test probe tips.
• Do not operate the instrument in an explosive atmosphere.
• To reduce the risk of fire or electric shock, do not expose this product to rain or moi-
sture.
• The meter is intended only for indoor use. To avoid electrical shock hazard, observe
the proper safety precautions when working with voltages above 60 VDC or 30 VAC
rms. These voltage levels pose a potential shock hazard to the user.
• Before and after hazardous voltage measurements, test the voltage function on a
known source such as line voltage to determine proper meter functioning.
• Keep your hands/fingers behind the hand/finger barriers (of the meter and the test
leads) that indicate the limits of safe access of the hand-held part during measure-
ment.
• Inspect test leads, connectors, and probes for damaged insulation or exposed metal
before using the instrument. If any defects are found, replace them immediately.
• This Clamp-on meter is designed to apply around or remove from uninsulated
hazardous live conductors. Individual protective equipment must be used if
hazardous live parts of the installation could be accessible.
• Exercise extreme caution when: measuring voltage >20 V // current >10 mA // AC
power line with inductive loads // AC power line during electrical storms // current,
5
when the fuse blows in a circuit with open circuit voltage >1000 V // servicing CRT
equipment.
• Remove test leads before opening the case to change the battery.
• Disconnect circuit power and discharge all high-voltage capacitors before testing
resistance,continuity, diodes, or capacitance.
• To avoid false readings, which could lead to possible electric shock or personal
injury, replace the batteries as soon as the low battery indicator () appears.
Unpacking and Inspection
Your shipping carton should include:
1 Digital clamp meter
1 Carrying case
1 Test lead set (one black, one red)
1 Two coin cell batteries
1 Manual
If any of the items are damaged or missing, return the complete package to the place of
purchase for an exchange.
OPERATION CAUTION
The Hz button will alternate the display between the voltage function selected and
frequency reading.
Measuring DC Voltage - See Figure 1
1. Set the Function Switch to V.
2. Connect the test leads: Red to +, Black to COM.
3. Connect the test probes to the circuit test points.
4. Read the display, and if necessary, correct any overload (0L) conditions.
Measuring AC Voltage - See Figure 2
1. Set the Function Switch to V.
2. Connect the test leads: Red to +, Black to COM.
3. Connect the test probes to the circuit test points.
4. Read the display, and if necessary, correct any overload (0L) conditions.
6
Measuring AC Current - See Figure 3
1. Set the Function Switch to A position.
2. Open spring-loaded clamp by pressing the lever on left side of meter.
3. Position clamp around one wire or conductor and release the clamp lever. Make sure
that the clamp is entirely closed. The clamp must be positioned around only one con-
ductor. If it is placed around two or more current carrying conductors, the reading is
FALSE.
4. Read the displayed value, and if necessary, correct any overload (0L) conditions.
Measuring Frequency - See Figure 3
The Voltmeter detects the frequency of the voltage applied to the test leads.
1. Set-up AC voltage measurement and press the Hz button.
2. Read the frequency value on the display .
CAUTION
Using the Resistance, Continuity, Diode or Capacitance functions on a live circuit will
produce false results and may damage the instrument. In many cases the suspected
component must be disconnected from the circuit to obtain an accurate measurement
reading.
Measuring Resistance - See Figure 4
1. Set the Function Switch to Ω.
2. Connect the test leads: Red to +, Black to COM.
3. Turn off power to the circuit being measured.
4. Discharge any capacitors that may inuence the reading.
5. Connect the test probes across the resistance.
6. Read the display. If 0L appears on the highest range, the resistance is too large to be
measured or the circuit is an open circuit.
7
Continuity Testing - See Figure 5
1. Set the Function Switch to Ω and press the SELECT button until is displayed.
2. Connect the test leads: Red to +, Black to COM.
3. Turn off power to the circuit being measured.
4. Discharge any capacitors that may influence the reading.
5. Connect the test probes across the resistance or the two points of test.
6. Listen for the tone that indicates continuity (>10 Ω and < 120 Ω).
Testing Diodes - See Figure 6
1. Set the Function Switch to Ω and press the SELECT button until is displayed.
2. Connect the test leads: Red to +, Black to COM.
3. Turn off power to the circuit being measured.
4. Free at least one end of the diode from the circuit.
5. Connect the test probes across the diode noting polarity.
6. Read the display. A good diode has a forward voltage drop of about 0.6 V. An open
or reverse biased diode will read .0L.
Measuring Capacitance - See Figure 7
1. Set the Function Switch to Ω and press the SELECT button until is displayed.
2. Connect the test leads: Red to +, Black to COM.
3. Turn OFF power to the circuit being measured.
4. Discharge the capacitor using a 100 kΩ resistor.
5. Free at least one end of the capacitor from the circuit.
6. Connect the test probes across the capacitor.
7. Read the display.
8. Relative zero mode can be used to zero out the parasitic capacitance of the leads
and the internal protection circuitry of the meter when measuring low capacitance
in the order of Pico Farad (pF).
Measuring Temperature - See Figure 8
1. Set the Function Switch to °F / °C and press the SELECT button until correct tempera-
ture range is displayed.
2. Connect the thermocouple to the input jacks: + to +, - to COM.
You can also use a plug adapter TA-1A (optional purchase) with banana pins to type-K
socket to adapt other type-K standard mini plug temperature probes.
8
Measuring μA Current - See Figure 9
1. Set the Function Switch to and press the SELECT button for AC or DC is displayed.
2. Connect the test leads: Red to +, Black to COM.
3. Turn OFF power to the circuit being measured and break the circuit for connecting
test leads.
4. Turn ON the circuit and read the display.
μA Current function
Application notes:
The DCμA function is designed especially for HVAC/R ame sensor applications. The
0.1μA resolution is useful for identifying the minute current changes in ame detector
applications. Flame signal current check should indicate steady ame signal of at least
2μA for a rectication type, or 1.5μA for an ultraviolet type (8μA for self checking
systems). If a ame signal current with inadequate strength or uctuation beyond 10%,
check the following to avoid the risk of unwanted ame relay dropout :
1-1) For gas or oil flames (Minipeeper):
• Low supply voltage
• Detector location
• Defective detector wiring
• Dirty viewing windows
• Faulty Minipeeper
1-2) For oil flames (Photocell):
• Detector location & wiring
• Smoky flame or poorly adjusted air shutter
• Faulty Photocell
• Temperature over 165 °F (74 °C) at photocell
1-3) For gas flames (Flame Rod):
• Ignition interference (A flame signal current difference with the ignition both on
and off greater than 0.5μA indicates the presence of ignition interference)
• Insufficient ground (must be at least 4 times the detector area)
• Flame lifting off burner head (ground), or not continuously in contact with the
flamerod
• Temperature in excess of 600 °F (316 °C) at the flame electrode insulator causing
short to ground.
9
FEATURES
HOLD / MAX
The HOLD feature freezes the display when the button is pressed. The MAX feature
compares and displays the measured maximum value as fast as 30ms with auto-ranging
capability.
HOLD
Press the HOLD button momentarily toggles to hold mode for the ACA function. To
release the HOLD feature momentarily press the HOLD button.
MAX
Press the HOLD button for 1 second or more activates the MAX HOLD feature for the
ACA function. To release the MAX HOLD feature press the HOLD button for 1 second or
more.
Auto Power Off (APO)
When the meter is on, the Auto Power Off (APO) feature will switch the meter into a
sleep mode automatically to extend battery life after approximately 30 minutes of no
slide-switch nor push button operations. To wake up the meter from APO, press the
buttons momentarily or set the slide-switch to the OFF position and then slide back on
again. Always set the slide-switch to the OFF position manually when the meter is not in
use.
MAINTENANCE WARNING
To avoid electrical shock, disconnect the meter from circuit, remove the test leads from
the input jacks and turn OFF the meter before opening the case. Do not operate the
meter with open case.
Trouble Shooting
If the instrument fails to operate, check batteries and test leads etc., and replace as
necessary. Double check operating procedure as described in this user’s manual.
The voltage and resistance measurement circuits are protected by fusible resistors and
a parallel high resistance path. If the instrument voltage-resistance input terminal has
been subjected to high voltage transients (caused by lightning or switching surges in the
system), the series fusible input resistors will open like fuses and the voltmeter will read
approximately 85% of the actual value and cause the resistance range to not work. The
meter voltage reading (approximately 15% low) will let the user know that the meter has
been damaged, and the circuit under test is active.
Autres manuels pour ACD-14 PLUS
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Amprobe Multimètre
Amprobe
Amprobe 37XR-A Manuel utilisateur
Amprobe
Amprobe 30XR-A Manuel utilisateur
Amprobe
Amprobe AC75 Manuel utilisateur
Amprobe
Amprobe HD110C Manuel utilisateur
Amprobe
Amprobe AM-100 Manuel utilisateur
Amprobe
Amprobe AM90 Manuel utilisateur
Amprobe
Amprobe 5XP-A Manuel utilisateur
Amprobe
Amprobe ACD-14-PRO Manuel utilisateur
Amprobe
Amprobe 5XP-A Manuel utilisateur
Amprobe
Amprobe AM535 Manuel utilisateur
Amprobe
Amprobe ACDC-400 Manuel utilisateur
Amprobe
Amprobe AM-250 Manuel utilisateur
Amprobe
Amprobe CDM-1 Manuel utilisateur
Amprobe
Amprobe AM-140 Manuel utilisateur
Amprobe
Amprobe AM-500 Manuel utilisateur
Amprobe
Amprobe AD40B Mode d'emploi
Amprobe
Amprobe AD105A Manuel utilisateur
Amprobe
Amprobe 5XP-A Manuel utilisateur
Amprobe
Amprobe ACD-6 Pro Manuel utilisateur
Amprobe
Amprobe ac68C Manuel utilisateur
Manuels Multimètre populaires d'autres marques
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manuel utilisateur
PeakTech
PeakTech 4000 Manuel d'utilisation et d'entretien
YOKOGAWA
YOKOGAWA 90050B Manuel utilisateur
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manuel utilisateur
Fluke
Fluke 8846A Manuel d'utilisation et d'entretien
Tempo Communications
Tempo Communications MM200 Manuel utilisateur
