Amprobe AM-560 Manuel utilisateur

AM-560

Advanced HVAC

Multimeter

AM-570

Industrial Multimeter

User Manual

EN FR ES

www. .com information@itm.com1.800.561.8187

English

AM-560

Advanced HVAC Multimeter

AM-570

Industrial Multimeter

User Manual

10/2017, Rev.4

www. .com information@itm.com1.800.561.8187

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and workmanship for one year from

the date of purchase unless local laws require otherwise. This warranty does not cover fuses,

disposable batteries or damage from accident, neglect, misuse, alteration, contamination, or

abnormal conditions of operation or handling. Resellers are not authorized to extend any other

warranty on the behalf of Amprobe. To obtain service during the warranty period, return the

product with proof of purchase to an authorized Amprobe Service Center or to an Amprobe

dealer or distributor. See Repair Section for details. THIS WARRANTY IS YOUR ONLY REMEDY.

ALL OTHER WARRANTIES - WHETHER EXPRESS, IMPLIED OR STATUTORY - INCLUDING IMPLIED

WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, ARE HEREBY

DISCLAIMED. MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL

OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since

some states or countries do not allow the exclusion or limitation of an implied warranty or of

incidental or consequential damages, this limitation of liability may not apply to you.

Repair

All Amprobe returned for warranty or non-warranty repair or for calibration should be

accompanied by the following: your name, company’s name, address, telephone number, and

proof of purchase. Additionally, please include a brief description of the problem or the service

requested and include the test leads with the meter. Non-warranty repair or replacement charges

should be remitted in the form of a check, a money order, credit card with expiration date, or a

purchase order made payable to Amprobe.

In-warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before requesting repair. During the

warranty period, any defective test tool can be returned to your Amprobe distributor for an exchange

of distributors near you. Additionally, in the United States and Canada, in-warranty repair and

replacement units can also be sent to an Amprobe Service Center (see address below).

Non-warranty Repairs and Replacement – United States and Canada

Non-warranty repairs in the United States and Canada should be sent to an Amprobe Service

Center. Call Amprobe or inquire at your point of purchase for current repair and replacement rates.

Non-Warranty Repairs and Replacement – Europe

*(Correspondence only – no repair or replacement available from this address. European customers please

contact your distributor.)

**single contact address in EEA Fluke Europe BV

www. .com information@itm.com1.800.561.8187

AM-560 Advanced HVAC Multimeter

AM-570 Industrial Multimeter

1Flash light

2LCD Display

3Push buttons (See making measurement for button functions)

4AM-570: Low-impedance button

AM-560: Backlight button

5Rotary switch

6SELECT button

7Input terminal for voltage, diode, capacitance, resistance,

continuity and temperature measurement

8COM (return) terminal for all measurements

9Input terminal for AC/DC mA/uA measurement

10 Input terminal for AC/DC A measurement to10A

4 46

www. .com information@itm.com1.800.561.8187

Screen Display

1Auto- or Manual- range

2Direct current

3Negative reading

4Alternate current

5True-rms value

6Low battery indicator

7Data hold

8Diode test

9Continuity test

10 Relative zero mode

11 Non-contact Voltage

detection mode

12 Measurement units

for Resistance

13 Measurement units

for Frequency

14 Measurement units for Voltage

15 Measurement units for Current

2 4

10 19 2011 21

13 12

14 15

81 2223

16 Measurement units for Capacitance

17 Duty cycle

18 Auto power off

19 Maximum / minimum reading

memory

20 Positive / negative peak

reading memory

21 Measurement unit for temperature

22 Low-pass filter

23 400KΩlow-impedance test

(AM-570 only)

24 Temperature measurement T1 or T2

25 Temperature measurement T1 - T2

26 Warning for error input terminals

connection for test leads

27 Hazardous Voltage presence

28 Analog bar graph display

www. .com information@itm.com1.800.561.8187

AM-560 Advanced HVAC Multimeter

AM-570 Industrial Multimeter

CONTENTS

SYMBOL.................................................................................................................2

SAFETY INFORMATION .........................................................................................2

UNPACKING AND INSPECTION .............................................................................3

FEATURES...............................................................................................................4

MAKING MEASUREMENT .....................................................................................5

Rotary Switch Positions ....................................................................................6

Function Buttons ..............................................................................................6

Measuring AC and DC Voltage ........................................................................9

Low Pass Filter...................................................................................................9

Measuring Frequency / Duty Cycle...................................................................11

Measuring AC and DC Current ........................................................................13

Measuring Resistance .......................................................................................14

Measuring Continuity ......................................................................................15

Measuring Capacitance ....................................................................................16

Measuring Diode...............................................................................................17

Measuring Temperature °C / °F ........................................................................18

Non-Contact Voltage Detection.......................................................................19

SPECIFICATIONS ....................................................................................................20

MAINTENANCE......................................................................................................24

BATTERY AND FUSE REPLACEMENT.....................................................................25

www. .com information@itm.com1.800.561.8187

SYMBOLS

Caution! Risk of electric shock.

Caution! Refer to the explanation in this manual

Alternating Current (AC)

Direct Current (DC)

The equipment is protected by double insulation or reinforced

insulation

Earth ground

Audible tone

Battery

Complies with European directives

Conforms to relevant Australian standards

Canadian Standards Association (NRTL/C)

Do not dispose of this product as unsorted municipal waste

Contact a qualified recycler

SAFETY INFORMATION

The meters comply with:

IEC/EN 61010-1 3rd Edition Pollution Degree 2, Measurement Category IV 600V

and Measurement Category III 1000V

IEC/EN 61010-2-31 for test leads

EMC IEC/EN 61326-1

Measurement Category IV (CAT IV) is for measurements performed at the

source of the low-voltage installation. Examples are electricity meters and

measurements on primary overcurrent protection devices and ripple control

units.

Measurement Category III (CAT III) is for measurements performed in the

building installation. Examples are measurements on distribution boards,

www. .com information@itm.com1.800.561.8187

circuit- breakers, wiring, including cables, bus-bars, junction boxes, switches,

socket-outlets in the fixed installation, and equipment for industrial use

and some other equipment, for example, stationary motors with permanent

connection to the fixed installation.

WARNING: Read before using

• To avoid possible electrical shock or personal injury, follow these

instructions and use the Meter only as specied in this manual.

• Do not use the Meter or test leads if they appear damaged, or if

the Meter is not operating properly. If in doubt, have the Meter

serviced.

• Always use the proper function and range for measurements.

• Before rotating the function range selection switch, disconnect

test probe from circuit under test.

• Verify the Meter’s operation by measuring on a known voltage

source.

• Do not apply more than the rated voltage, as marked on the Meter,

between the test probe or between any test probe and earth ground.

• Use the Meter with caution for voltages above 30 V ac rms, 42 V

ac peak, or 60 Vdc. These voltages pose electrical shock hazards.

• Disconnect circuit power and discharge all high-voltage capacitors

before testing resistance.

• Do not use the Meter around explosive gas or vapor.

• When using the test leads, keep your ngers behind the nger guards.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 AM-560 or AM-570 Multimeter

1 Pair of test leads

2 Temperature probes

1 Temperature adaptor

1 Velcro strap

1 9V (6F22) battery (installed)

1 Users manual

1 Carrying case

If any of the items are damaged or missing, return the complete package to

the place of purchase for an exchange.

www. .com information@itm.com1.800.561.8187

FEATURES

The multimeter designed for professional HVAC technicians. The AM-560

measures a complete range of electrical parameters and features. Key

functions include: temperature, capacitance to check the motor startup

capacitors, micro amps for flame sensor troubleshooting, and a low pass filter

to take accurate measurements on variable frequency drives. With a built-

in flashlight, and non-contact voltage detection, the AM-560 is the choice

multimeter for the professional HVAC technician. This meter is safety rated to

CAT IV 600V and CAT III 1000V for the most advanced HVAC troubleshooting

needs.

The Amprobe AM-570 is a fully featured multimeter designed for professional

electricians who need to maintain service or troubleshoot advanced electrical

systems. True-rms sensing accurately measures voltage on systems affected by

harmonics; built-in flashlight allows you to identify wires while working in

dark conditions, and non-contact voltage detection allows for quick go-no-go

checks without the need for an additional tool. The AM-570 also features dual

input temperature measurement, a low-impedance function to detect stray

voltage, and a low pass filter to accurately take measurements on variable

frequency drives. Safety rated to CAT IV 600V and CAT III 1000V for use in the

most industrial applications.

• Measurements: AC/DC Voltage up to 1000V, ac/dc current, Resistance,

Frequency, Capacitance, Temperature, duty cycle.

• Special Functions:

- Low Z - to detect “ghost” voltages (for AM-570 only)

- Low pass filter for variable frequency drives

- Non-contact Voltage detection

- Audible continuity

- Diode test

• Dual reading backlit LCD display with analog bargraph

• Events:

- Data hold

- MAX / MIN memory

- Peak hold (crest)

- Relative zero mode

• Built-in flash light

• Built-in test leads storage and “third hand holder”

• Warning against improper test leads connection

www. .com information@itm.com1.800.561.8187

• Auto and manual ranging

• Auto power off

• Low battery warning

• Velcro strap to hang a meter

• Safety: CAT IV 600V, CAT III 1000V

MAKING MEASUREMENT



1. Use the proper function and range for measurements.

2. To avoid possible electrical shock, personal injury or damages to the

Meter, disconnect circuit power and discharge all high-voltage capacitors

before testing resistance and diode.

3. Connecting test leads:

• Connect the common (COM) test lead to the circuit before connecting

the live lead;

• After measurement, remove live lead before removing the common

(COM) test lead from the circuit

4. Symbol “OL” is displayed on LCD when the measurement is out of range.

Rotary Switch Positions

Switch Position Measurement Function

/ AC voltage measurement / Low-pass filter (1kHz).

Use SELECT button to select alternate function.

/ NCV DC voltage measurement / Non-contact Voltage

detection.Use SELECT button to select alternate function.

/ / % DC millivolt measurement / Frequency / Duty cycle

Use SELECT button to select alternate function.

/ / Resistance / Capacitance / Continuity measurement.

Use SELECT button to select alternate function.

Voltage measurement of diode PN junction (diode test).

°C °F Temperature measurement.

Use SELECT button to select temperature unit °C or °F.

μA mA

10A

AC or DC current measurement.

Use SELECT button to select alternate function ac or dc

www. .com information@itm.com1.800.561.8187

Autres manuels pour AM-560

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Amprobe Multimètre

Amprobe

Amprobe AM-500 Manuel utilisateur

Amprobe

Amprobe AM-540 Manuel utilisateur

Amprobe

Amprobe 38XR-A Manuel utilisateur

Amprobe

Amprobe ac68C Manuel utilisateur

Amprobe

Amprobe 37XR-A Manuel utilisateur

Amprobe

Amprobe Hexagon 60 Manuel utilisateur

Amprobe

Amprobe AU92 Manuel utilisateur

Amprobe

Amprobe AM-510 Manuel utilisateur

Amprobe

Amprobe KWC-2000 Manuel utilisateur

Amprobe

Amprobe AMP-330 Manuel utilisateur

Amprobe

Amprobe ACD-11 Manuel utilisateur

Amprobe

Amprobe AM-250 Manuel utilisateur

Amprobe

Amprobe 30XR-A-D Manuel utilisateur

Amprobe

Amprobe ACD-14 PLUS Manuel utilisateur

Amprobe

Amprobe AM-120 TRMS Manuel utilisateur

Amprobe

Amprobe ACD-6 Pro Manuel utilisateur

Amprobe

Amprobe AM-510 Manuel utilisateur

Amprobe

Amprobe AM-560 Manuel utilisateur

Amprobe

Amprobe AM-6B Manuel utilisateur

Amprobe

Amprobe DM73C Manuel utilisateur

Amprobe

Amprobe 30XR-A Manuel utilisateur

Amprobe

Amprobe 15XP-A Manuel utilisateur

Amprobe

Amprobe ACDC-600A Manuel utilisateur

Amprobe

Amprobe PM51A Manuel utilisateur

Manuels Multimètre populaires d'autres marques

Agilent Technologies

Agilent Technologies 34420A Manuel utilisateur

Fluke

Fluke 83 Manuel utilisateur

Hameg

Hameg HM 8012 Manuel utilisateur

Mastech

Mastech MY70 Manuel utilisateur

Steren

Steren MUL-300 Manuel utilisateur

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuel utilisateur

PeakTech

PeakTech 4000 Manuel d'utilisation et d'entretien

YOKOGAWA

YOKOGAWA 90050B Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuel utilisateur

Fluke

Fluke 8846A Manuel d'utilisation et d'entretien

Tempo Communications

Tempo Communications MM200 Manuel utilisateur

Elenco Electronics

Elenco Electronics CM-1555 Manuel utilisateur

Mastech

Mastech MS8238C Manuel utilisateur

SDAR

SDAR 830A, 830B, 830D, 830C Manuel utilisateur

RS PRO

RS PRO RS-9519BT Manuel utilisateur

BGS technic

BGS technic 8890 Manuel utilisateur

Morris

Morris 57074 Manuel utilisateur