Amprobe AC75 Manuel utilisateur

AC75B

AC Digital Clamp Multimeter

Users Manual

99 Washington Street

Melrose, MA 02176

Fax 781-665-0780

TestEquipmentDepot.com

AC75B Clamp-on Multimeter

Contents

Safety Information ........................................................................................2

Symbols Used in this Manual........................................................................3

Introduction ..................................................................................................4

Making Measurements...............................................................................4

Additional Features ....................................................................................4

Product Maintenance ....................................................................................4

Maintenance...............................................................................................4

Cleaning.....................................................................................................4

Troubleshooting.........................................................................................5

Battery Replacement..................................................................................5

Repair ...........................................................................................................6

Specifications................................................................................................7

General Specifications................................................................................7

Environmental Specifications.....................................................................7

Electrical Specifications .............................................................................7

Safety Information

To ensure safe operation and usage of the meter, follow these instructions.

Failure to observe warnings can result in severe injury or death.

•To avoid possible electric shock or personal injury, follow these

guidelines:

•Do not use the meter if it is damaged. Before you use the meter,

inspect the case. Look for cracks or missing plastic. Pay particular

attention to the insulation surrounding the connectors.

•Inspect the test leads for damaged insulation or exposed metal.

Check the test leads for continuity.

•Replace damaged test leads before you use the meter.

•If this product is used in a manner not specified by the

manufacturer, the protection provided by the equipment may be

impaired.

•Do not use the meter if it operates abnormally. Protection may be

impaired. When in doubt, have the meter serviced.

•Do not operate the meter around explosive gas, vapor, or dust.

•Do not apply more than the rated voltage, as marked on the meter,

between terminals or between any terminal and earth ground.

•Before use, verify the meter’s operation by measuring a known

voltage.

•When measuring current, turn off circuit power before connecting

the meter in the circuit. Remember to place the meter in series with

the circuit.

•Do not attempt to repair this meter. There are no user serviceable

parts.

•Use caution when working above 30 V ac rms, 42 V peak, or 60 V

dc. Such voltages pose a shock hazard.

•When using the probes, keep your fingers behind the finger guards

on the probes.

•Connect the common test lead before you connect the live test lead.

When you disconnect test leads, disconnect the live test lead first.

•Remove test leads from the meter before you open the battery door.

•Do not operate the meter with the battery door removed or

loosened.

•To avoid false readings, which could lead to possible electric shock

or personal injury, replace the batteries as soon as the low battery

indicator (N) appears.

•Only use a 9 Volt battery, properly installed in the meter case, to

power the meter.

•To avoid the potential for fire or electrical shock, do not connect the

thermocouple to electrically live circuits.

•Disconnect circuit power and discharge all high-voltage capacitors

before testing resistance,continuity, diodes, or capacitance.

Symbols Used in this Manual

N Battery WRefer to the manual

TDouble insulated XDangerous Voltage

FDirect Current JEarth Ground

BAlternating Current RAudible tone

;Conforms to relevant

Australian standards. )Canadian Standards

Association

(Canadian and US)

P Complies with EU

directives , Application around and

removal from HAZARDOUS

LIVE conductors is

permitted.

Introduction

The AC75B digital clamp-on multimeter, is a fully featured meter that also

measures temperature using a Type K probe (included). The AC75B has full

Category safety ratings and is CAT III, 600 V.

Making Measurements

Measurement Functions

•AC and DC Volts (V/v) See Figure -4-

•Resistance (O) See Figure -5-

•Diode/Continuity (G/C) See Figure –6-

•DC Current (DC μA) See Figure –7-

•Capacitance (P) See Figure –8-

•Temperature (°C/°F) See Figure –9-

•AC Current (a) See Figure –11-

Additional Features

Auto Power Off/Auto Power Off Disable See Figures -2- and –3-

The meter will automatically shut itself off after approximately 10 minutes

after power is turned on, or no activity has occurred with the meter. The

meter will beep when it turns off. Turn the rotary dial to reactivate the

meter.

The Auto Power Off feature can be disabled to keep the meter from going to

sleep. Press the BACKLIGHT button and then switch the rotary knob to

power on the meter.

Backlight See Figure -12-

The AC75B backlight illuminates the entire display for easy measurement

viewing in dark work environments. The backlight is activated for 60

seconds once the button is pressed.

HOLD Measurements See Figure -10-

The HOLD button allows the meter to capture and continuously display a

measurement reading. To use the HOLD feature, make a measurement,

when the reading has stabilized, press the HOLD button. The measurement

value will be captured on the display. Press the HOLD button again to

release the value.

Product Maintenance

Maintenance

Do not attempt to repair this meter. It contains no user serviceable parts.

Repair or servicing should only be performed by qualified personnel.

Cleaning

To clean the meter, periodically wipe the case with a soft moistened cloth.

To avoid damage to the plastic components do not use benzene, alcohol,

acetone, ether, paint thinner, lacquer thinner, ketone or other solvents to

clean the meter.

Troubleshooting

If the meter appears to operate improperly, check the following items first.

1. Review the operating instructions to ensure the meter is being used

properly.

2. Make sure the battery is in good condition. The low battery symbol N

appears when the battery falls below the level where accuracy is

guaranteed. Replace a low battery immediately.

Battery Replacement

To replace the battery

1. Turn the meter off and remove the test leads.

2. Loosen the screw and remove the battery door.

3. Replace the battery using an alkaline 9 V battery. See General

Specifications for detailed battery specifications.

4. Replace the battery cover and tighten the screw. Recycle the battery

using approved methods.

XWWARNING

To avoid electrical, shock remove the test leads from both the meter and

the test circuit before accessing the battery or the fuses.

Specifications

General Specifications

Display: 3 ¾ digit large scale liquid crystal display (LCD)

Display Count: 4000 counts

Measuring Rate: 1.5 times per second

Overrange Display: 0o is displayed for Ωfunctions. Actual value is shown

for A, V, and temperature functions.

Automatic Power Off Time:Approximately 10 minutes after power on

Low battery indication: The Nsymbol is displayed when the battery

voltage drops below the operating level for accurate results.

Power: Single standard 9 V battery, NEDA160A.

Battery Life: 200 hours with an alkaline 9 V battery.

Environmental Specifications

Indoor Use

Calibration: One year calibration cycle

Operating Temperature:

0 °C to 30 °C at ≥80 % R.H.

30 °C to 40 °C at ≥75 % R.H.

40 °C to 50 °C at ≥45 % R.H.

Storage Temperature: -20 °C to 60 °C at 0 to 80 % R.H. (battery removed)

P, )

Overvoltage Category:

IEC 61010-1 CAT III - 600 V, CAT II 1000 V, Pollution Degree 2

EN61010-2-032

CAN/CSA C22.2 No. 1010.1-92

CAN/CSA C22.2 No. 1010.1B-92

CAN/CSA C22.2 No. 1010.2.032-96

Altitude: ≤2000 M (6562 Feet)

Conductor Size: ≤32 mm diameter (1.25 in)

EMC: EN61326-1.

Shock Vibration:Sinusoidal vibration per MIL-PRF-28800F (5 to 55 Hz, 3 g

maximum)

Drop Protection:4 foot drop to hardwood on concrete floor

Electrical Specifications

Accuracy: ±(% reading + number of digits) at 23 °C ±5 °C at <80 % R.H.

Temperature Coefficient: Add 0.2 x (Specified Accuracy)/°C, <.18 °C,

>28 °C.

DC/AC VOLTS

Range DC Accuracy AC Accuracy

4.000 V

40.00 V

400.0 V

1000 V dc/750 V ac

±(0.9 % + 2 dgt)

±(1.5 % + 5 dgt)

50 Hz to 500 Hz

Overvoltage Protection: DC 1000 V or AC 750 V rms

Input Impedance: 10 MΩ//less than 100 ρF

CMRR/NMRR: (Common Mode Rejection Ratio/Normal Mode Rejection

Ratio)

V ac

CMRR >60 dB at DC, 50 Hz/60 Hz

V dc

CMRR >100 dB at DC, 50 Hz/60 Hz

NMRR >50 dB at DC, 50 Hz/60 Hz

AC Conversion Type: Average sensing rms indication.

Resistance

Range Accuracy

2400.0 Ω±(1.0 % + 2 dgt)

4.000 kΩ

40.00 kΩ

400.0 kΩ

±(0.7 % + 2 dgt)

4.000 MΩ±(1.0 % + 2 dgt)

140.00 MΩ±(1.5 % + 2 dgt)

Overload Protection: 1000 V dc/750 V ac

Open Circuit Voltage: -1.3 V approx.

1<100 dgt rolling

210 dgt rolling

Diode Check and Continuity

Resolution Accuracy

10 mV ±(1.5 % + 5 dgt)

From 0.4 V to 0.8 V

Max Test Current: 1.5 mA

Max Open Current: 3 V

Overload Protection: 1000 V dc/750 V ac

Continuity: Built-in buzzer sounds when resistance is less than

approximately 100 Ω. Response time is approximately 100 msec

DC μA

Range Accuracy

400.0 μA

4000 μA ±(1.0 % + 2 dgt)

Voltage Burden: <5 mV/μA

Overload Protection: 1000 V dc/750 V ac

Resolution: 100 nA

Capacitance

Range Accuracy

4.000 nF ±(3.0 % + 20 dgt)

40.00 nF

400.0 nF

4.000 μF

40.00 μF

400.0 μF

14.000 mF

±(2.0 % + 8 dgt)

Overload Protection: 1000 V dc/750 V ac

1<50 dgt fluctuating

AC Current

Function Range AC Accuracy

0.0 to 399.9 A

(50 to 60 Hz) 400.0 to 600.0 A* ±(1.9 % + 5 digits)

*0.0 to 500.0 A Continuous

501 A to 600.0 A 10 minutes maximum followed by 10 minutes cooling

period.

Overload Protection: 1000 V dc/750 V ac

AC Conversion Type: Average sensing rms display

Position Error: ±1.5 % of reading

Temperature

Function Range Accuracy

-40 °C to 0.1 °C 1 % ±4 °C

°C 0 °C to 400.0 °C 1 % ±3 °C

-40 °F to 32 °F 1 % ±8 °F

32 °F to 750 °F 1 % ±6 °F

°F

750 °F to 1000 °F 1 % ±8 °F

Overload Protection: 1000 V dc/750 V ac

Table des matières

Autres manuels Amprobe Multimètre

Amprobe

Amprobe DM7C Manuel utilisateur

Amprobe

Amprobe AM-530 Manuel utilisateur

Amprobe

Amprobe 33XR-A Manuel utilisateur

Amprobe

Amprobe ACDC-400 Manuel utilisateur

Amprobe

Amprobe ACDC-400 Manuel utilisateur

Amprobe

Amprobe DM73C Manuel utilisateur

Amprobe

Amprobe CR50A Manuel utilisateur

Amprobe

Amprobe 34XR-A Manuel utilisateur

Amprobe

Amprobe ACD-14 PLUS Manuel utilisateur

Amprobe

Amprobe AM-6B Manuel utilisateur

Amprobe

Amprobe AM535 Manuel utilisateur

Amprobe

Amprobe DM73C Manuel utilisateur

Amprobe

Amprobe AMP-210 Manuel utilisateur

Amprobe

Amprobe AMP-330 Manuel utilisateur

Amprobe

Amprobe AM-1200 Manuel utilisateur

Amprobe

Amprobe AM-1250 Manuel utilisateur

Amprobe

Amprobe 38XR-A Manuel utilisateur

Amprobe

Amprobe ACD-10 TRMS-PLUS Manuel utilisateur

Amprobe

Amprobe AM-52 Manuel utilisateur

Amprobe

Amprobe ACD-11 Manuel utilisateur

Amprobe

Amprobe 37XR-A Manuel utilisateur

Amprobe

Amprobe 34XR-A Manuel utilisateur

Amprobe

Amprobe AM90 Manuel utilisateur

Amprobe

Amprobe AM-500 Manuel utilisateur

Manuels Multimètre populaires d'autres marques

Agilent Technologies

Agilent Technologies 34420A Manuel utilisateur

Fluke

Fluke 83 Manuel utilisateur

Hameg

Hameg HM 8012 Manuel utilisateur

Mastech

Mastech MY70 Manuel utilisateur

Steren

Steren MUL-300 Manuel utilisateur

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuel utilisateur

PeakTech

PeakTech 4000 Manuel d'utilisation et d'entretien

YOKOGAWA

YOKOGAWA 90050B Manuel utilisateur

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuel utilisateur

Fluke

Fluke 8846A Manuel d'utilisation et d'entretien

Tempo Communications

Tempo Communications MM200 Manuel utilisateur

Elenco Electronics

Elenco Electronics CM-1555 Manuel utilisateur

Mastech

Mastech MS8238C Manuel utilisateur

SDAR

SDAR 830A, 830B, 830D, 830C Manuel utilisateur

RS PRO

RS PRO RS-9519BT Manuel utilisateur

BGS technic

BGS technic 8890 Manuel utilisateur

Morris

Morris 57074 Manuel utilisateur