AMPLIFIED ENGINEERING fatbox G3 Manuel utilisateur
THE MANUAL
If it is for demanding HSPA+ M2M and IoT
deployments that require Security with
Smart Remote access., the FATBOX G3
router is a hardy and robust gateway suited
for Ethernet and Serial Port equipped
devices. Lab tested and certied for CE and
FCC part 15.
EDITION 01.2 / DEC 2015
DESIGNED IN AUSTRALIA. ASSEMBLED IN USA.
fatbox G3
Table of Contents
SAFETY OF USE 3
ABOUT 4
G3 SPECIFICATIONS 4
HARDWARE 5
BOARD INTERFACE 6
SETTING UP 7
SIM INSTALLATION 7
LOGGING IN 8
WEB MANAGEMENT 9
QUICK START 9
LAN ETHERNET 10
WAN CELLULAR 11
PORT FORWARDING 12
DYNAMIC DNS 13
IPSEC VPN 14
SERIAL PORT 16
MANAGEMENT 17
SYSTEM STATUS 19
CONTACT US 20
fatbox G3
SECURITY + INTEGRATION
SAFETY OF USE
fatbox G3
!
ALL CONDITIONS
POWER SET UP
SIM CARD
CONFIGURING THE
ROUTER
All specialist electronic devices must be operated with due care to avoid damage or injuries and should be installed and
operated by a trained personnel.
DO NOT OPERATE THIS EQUIPMENT IN ENVIRONMENTS CONTAINING POTENTIALLY EXPLOSIVE GASES OR LIQUIDS, EXAMPLE,
GAS STATIONS AND CHEMICAL PLANTS AND EXPLOSIVE STORES.
Inadequate current or dips in voltage may cause the device to fail to connect to data services even if the LEDs are lighted up.
Supply over 30 VDC will damage the device
Never remove or insert SIM card when device has PWR switched in“ON”position. Damage caused to device or SIM in such case
will not be warranted.
Do not reboot/power-down the device until the writing process is acknowledged as completed.
fatbox G3
CELLULAR INTERFACE
· HSPA+ 14.4Mbps downlink and 5.76Mbps uplink
over 850/900/1900/2100MHz bands
· GSM 850/900/1800/1900 for GPRS and EDGE
· LTE (EU/Asia) option available on request
· RX Diversity antenna for optimum performance
MANAGEMENT
OPERATING CONDITIONS
· Designed for maximum uptime from available
network
· End-to-End PING connectivity testing with
Reboot
· Congurable PPP keep-alive function
· IP rewall
· IPSEC (PSK) VPN for secure networking
· DYNDNS and Port Forwarding
· SMS to Reboot function to remotely reboot
router (LUA Script)
· AT over Ethernet LAN e.g. to send SMS from a
PLC
- AT over serial (custom rmware)
· 12~24VDC (0.4/0.2A/0.1A @12VDC
Peak/Nominal/Idle)
· -40°C ~ +75°C Operating Temperature
NETWORK
ROBUSTNESS
SECURITY
NETWORKING
MANAGEMENT
POWER
TEMPERATURE
OPERATING SYSTEM
· Linux on ARM Cortex-A9 (IMX6 Solo/Dual/Quad options)
SERIAL INTERFACE
· RS-232/RS-485 ±15kV ESD Protected
· Integrated TCP Serial server
LAN INTERFACE
· 2 X 10/100BaseT Ethernet port
· 24VDC POE (Passive Input)
USER CUSTOM PROGRAMMING
· Lua scripting for user programed functionalities
· Available 2GB of on-board ash data storage
· Reduce cost and time to remotely manage equipment
GPS (FUTURE OPTION - PLS CONTACT US)
· Serial or Ethernet access to GPS data
· User on-board application to GPS data
1.1
G3 SPECIFICATIONS
ABOUT
SECURITY
The core thinking behind
the G3 hardware and
software design is the
layering of security in the
modes of access.
INTEGRATION
Lower system cost while
improving reliability
by integrating simple
user scripts to automate
simple data or input
monitoring and alerts
management
G3 DUO FOCUS
ABOUT
1.2
HARDWARE
VERSION SPECIFICATIONS
PERIPHERALS INCLUDED
fatbox G3
The FATBOX G3 is available in two versions.
INTERFACE
- LAN
- SERIAL
- I/O
- USB
DIMENSION
- L
- W
- H
INTEGRATED
MOUNTING
WEIGHT
· GSM antenna (with 2M wire)
High-gain outdoor antenna option
· CAT-5 LAN cable (3M)
· Power supply unit (230/110VAC to 24VDC 0.5A)
OEM
114mm
108mm
19mm
110g
STANDARD
149mm
111mm
37mm
375g
101mm
129mm
STANDARD VERSION
With rugged anodized
aluminium chassis
NOTE: The client is required
to have their own mounting
screws (M3 size) to suit the
surfaces the G3 will be on.
OEM VERSION
ABOUT
1.3
BOARD INTERFACE
fatbox G3
FRONT PLATE
BACK PLATE
cell1
signal
gps
cell2
amplified
engineering
fatbox G3
R
eth1dc eth0 serial dip
1 2 3 4TX RX IN GND
D- D+
amplified
engineering
fatbox G3
Power
Serial Input Port (4-way plug in terminal)
USB port
Antenna Port 2
GPS Antenna
Antenna Port 1
System Reset
Press <1 second, soft reset the router
Press >5 seconds, will revert
parameters to Factory Default
This is a 4-way general purpose
switch available to user application
program. DIP #4 (right-most) is
dedicated as ‘TEST MODE’ * which
is activated when DIP #4 is in ‘OFF/
down’ position during power up.
*
During ‘TEST MODE’, after power up is
stable (e.g. 1 minute) a program will
monitor a switch (contact between #3
and #4 of Serial Input Port)
Press #1, if INPUT (#3 of Serial Input
Port) is working, LED ‘YES’ will blink
once
Press #2, with a‘loop back’ wire
connected between #1(TX) and #2(RX)
of the Serial Input Port. The LED ‘YES’
will blink twice
Press #3, once a 3G/GPRS/EDGE session
is established, LED ‘YES’ will blink three
times
(Left to Right)
1 – TX output of serial port
2 – RX input of serial port
3 – INPUT, general purpose input port, switch to GND (pin 4) to activate
4 – GND
single: connection poor
dual: connection good
AUTOPING/
IPSEC/ Custom
Program
AUTOPING/
Custom Program
LED: POWER ON GENERIC ‘YES’ GENERIC ‘NO’ SIGNAL STRENTH LEVEL
Main LAN Port ETH0
(default: 192.168.1.1)
Second LAN Port ETH1
(default: 10.1.1.1)
DIP Switch
SETTING UP
fatbox G3
2.1
SIM INSTALLATION
WHAT YOU’LL NEED
1
3G Data Enabled micro SIM
Card
2
PC/Laptop with an
Ethernet port
3
SIM card network details –
APN/USERNAME/PASSWORD.
You would need to get this
information from
your operator.
INSERTING THE SIM CARD
STEP 1 of 6 - Dismantle the casing cover and slide out the PCB. Avoid touching the electronics, handle the board by the edges.
STEP 2 of 6 - Insert your micro SIM card into the SIM card slot. Push the metal latch left/right to lock/unlock.
Reassemble the metal casing.
STEP 3 of 6 - Connect the power adapter/antenna and plug the Ethernet cable to your pc.
STEP 4 of 6 - Power up the FATBOX G3.
(SIM card’s
orientation
ts as shown)
2.2
LOGGING IN
SETTING UP
fatbox G3
FATBOX CONSOLE
192.168.168.1 /cgi-bin/F ATBOX
Username
Password
LOGIN
fatbox G3
When you have connected
up the hardware to the
box, the web console can
be accessed at the address
192.168.1.1
For Security, after your rst
successfull log in, you will
be prompted to change
your username &
password.
The default username is:
admin
The default password is:
fatbox12345
STEP 5 of 6 - Launch your browser and enter address as 192.168.1.1
STEP 6 of 6 - Log in.
fatbox12345
admin
WEB
MANAGEMENT
fatbox G3
3.1
QUICK START
fatbox G3
MENU OPTIONS
Quick Start
LAN Ethernet
WAN Cellular
Port Forwarding
Dynamic DNS
IPSEC VPN
Serial Port
Management
System Status
Logout
Basic Settings for FATBOX 3G router for 3G WWW access
255.255.255.0
192.168.168.1
LAN Netmask
LAN IP Address
LAN (eth1 and eth0) Port Settings
3G HSUPA Cellular Settings
your_apn
APN
User Name (PAP/CHAP only)
Password (PAP/CHAP only)
SIM PIN Code (If required only)
UPDATE
Sets the IP address of LAN port on FATBOX
G3
Mask for setup range of subnet IP
addresses
Please check with your operator on this.
Setup the PIN code (usually 4-8 digit
numerics) if SIM PIN lock is enabled
This saves the settings onto the G3.
The Quick Start tab brings
all the settings you need to
establish an immediate
connection into a single
page.
WEB
MANAGEMENT
fatbox G3
3.2
LAN ETHERNET
fatbox G3
MENU OPTIONS LAN (eth0 + eth1) Port Settings
255.255.255.0
192.168.168.1
1
100
150
0
1c:bd:0e:00:00:01
LAN Netmask
DHCP Start
LAN Masquerade
DHCP Limit
Specic LAN device Masquerade
LAN IP Address
DHCP Disabled 1= disabled 0=enabled
e.g. xxx.xxx.xxx Start
xx.xx.xx.xx.xx.xx/xxx
xx.xx.xx.xx.xx.xx
Limit
1= Enabled, 0=Disabled
Advanced Settings
eth MAC
Quick Start
LAN Ethernet
WAN Cellular
Port Forwarding
Dynamic DNS
IPSEC VPN
Serial Port
Management
System Status
Logout
Sets the IP address of LAN port on FATBOX
G3
Setup the FATBOX G3 to automatically
assign IP addresses to your connected LAN
devices.
This would be the starting address for con-
nected devices. For the example above, the
rst device connected would be assigned
192.168.1.100.
This would be the limit for number of con-
nected devices. For the example above, the
last device connected would be assigned
192.168.1.150
This is to enable/disable masquerade
Sets the Ethernet MAC address of the
FATBOX G3
IP masquerading allows internal machines
that don’t have an ocially assigned IP ad-
dresses to communicate to other networks
and especially the Internet. Set this to the
specic device on your network.
UPDATE
Autres manuels pour fatbox G3
1
Table des matières
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité