Ammeter EPM-14 Manuel utilisateur
AMMETER
EPM-14
1 ......... This display shows to measured current.
2........... ESC button to exit from a menu any time.
3 ........... DOWN button.
4 ........... UP button.
5 ........... SET button. It is used to enter into the menu and to save the values.
If SET button is pressed for 3 seconds in the measurement mode,
you can enter into menus.
EPM-14 Menu Settings
After making the connections of the device as given in user manual, voltage is
supplied. Required settings must be done by using menus in order to have the
correct measurements and applications.
Current Transformer Menu
In this menu, current transformer ratio and current transformer secondary
value is set.
Precautions For Installation and Safe Use
- Failure to follow those instructions will result in death or serious injury.
- Disconnect all power before working on equipment.
- When the device connected to the network, do not remove the back panel.
- Do not try to clean the device with solvent or the like.Only clean the device
with dried cloth.
- Verify correct terminal connections when wiring.
- Electrical equipment should be serviced only by your component seller.
- Only for rack panel mounting.
- The fuse should be used F type and current boundary value must be 6A.
General Information
EPM-14 is designed to measure the current of the single phase systems.
Applications of EPM-14
1) It can measure Current in single phase systems.
2) You can observe demand and max. demand value of measured current with
2 different periods, also the calculation time for demand and max. demand value
can be determined from the dE-t (demand time) menu.
3) Current transformer ratio can be programmed,
[1....1000 (for X/5A), 1....5000 (for X/1A)]
4) A password can be arranged from CodE menu in order to prevent
change of the setting by unauthorized person.
Specific Functions of Buttons:
While device is in the measurement mode, some buttons and button groups have
below special functions.
In order to set CT ratio. In the measurement mode;
Press SET button (Ctr is displayed.)
Press ESC button one by one until CAnC is displayed.
Press SET button while SAUEis displayed. (If you press ESC button
or select CAnC option instead of SAUE, new data is cancelled
and the previous data is set.)
Find 4th digit value by scrolling UP/DOWN buttons.
Press SET button (4th digit of display blinks. If you set 3rd digit value
incorrect, you can set again by pressing ESC button.)
Press SET button for 3 secs.(trF menu is displayed)
Press SET button (Ctr menu is displayed)
Find 1st digit of the value which you want
to enter by scrolling UP/DOWN buttons.
Find 2nd digit value by scrolling
UP/DOWN buttons.
Press SET button (2nd digit of display
blinks. If you set 1st digit value incorrect,
you can set again by pressing ESC
button)
Find 3rd digit value by scrolling UP/DOWN buttons.
Press SET button (3rd digit of display blinks. If you set 2nd digit
value incorrect, you can set again by pressing ESC button.)
1
2 3 4 5
: When DOWN button is pressed, 1st demand value is displayed.
: When UP button is pressed, 1st max. demand value is displayed.
+: When ESC and DOWN buttons are pressed at the same time,
2nd demand value is displayed.
+: When ESC and UP buttons are pressed at the same time, 2nd
max. demand value is displayed.
+: When DOWN and UP buttons are pressed at the same time,
all demand and max. demand values are reset.
Current Transformer Ratio
In this menu, current transformer ratio is set.
[1 ...... 1000 (for X/5A), 1 ...... 5000 (for X/1A)]
Note: If the current transformer is not used between the system and
EPM-14, CT ratio must be set as 1.
For example: If a current transformer with 30 A / 5 A is used between
the system and EPM-14, CT ratio must be set as 6. (30/5=6)
Press SET button (Mosy left digit of display blinks)
By using UP/DOWN buttons, find SAUE
Current transformer secondary value setting
In this menu, current transformer secondary value can be set as 5A
or 1A.
Note: If the secondary value is changed from 5A to 1A, Ctr
(current transformer ratio) value is set as 5 times of previous value
automatically. If the secondary value is changed from 1A to 5A,
Ctr (CT ratio) value is set as 1/5 times of the previous value
automatically.
In order to set secondary value; in the measurement mode,
Press SET button SEC is displayed. (New value is entered but it is not
executed yet. In order to set the new value, please follow below steps)
Press ESC button one by one until CAnC is displayed.
Press SET button while SAUEis displayed. (If you press ESC button
or select CAnC option instead of SAUE, new data is cancelled
and the previous data is set.)
Press SET button for 3 secs. (trF menu is displayed)
Press SET button (Ctr menu is displayed.)
Set the secondary current value by using
UP/DOWN buttons
Press SET button (active secondary
value is displayed on display)
By using UP/DOWN buttons, find SAUE
By using UP/DOWN buttons, find SEC
menu.
1
No responsibility is assured by the manufacturer or any of its subsidiaries
for any consequences arising out of the use of this material.
AMMETER
EPM-14
dE-t (Demand Time - Demand calculation time) Menu:
2
dE-1 (1st Demand Time - 1st Demand calculation time) Menu
dE-1 demand time can be set between 1-60 minutes which is
independent from dE-2. In this time interval, 1st demand and 1st
max. demand value are calculated.
dE-2 (2nd Demand Time - 2nd Demand calculation time) Menu
dE-2 demand time can be set between 1-60 seconds which is
independent from dE-1. In this time interval, 2nd demand and 2nd
max. demand value are calculated.
In order to set demand calculation time; in measurement mode,
Press SET button. dE-1 or dE-2 is displayed (new value is entered but
it is not executed yet. In order to set the new value, please follow below
steps)
Press ESC button one by one until CAnC is displayed.
Press SET button while SAUEis displayed. (If you press ESC button
or select CAnC option instead of SAUE, new data is cancelled
and the previous data is set.)
Press SET button for 3 secs. (trF menu is displayed)
Press SET button (dE-1 menu is displayed)
By using UP/DOWN buttons, set 1st digit
By using UP/DOWN buttons, set 2nd
digit.
Press SET button (2nd digit of display
blinks. If you set 1st digit incorrect, you
can set again by pressing ESC button).
Press SET button (Most left digit of display blinks)
By using UP/DOWN buttons, find SAUE
By using UP/DOWN buttons, find dE-t menu.
By using UP/DOWN buttons, select dE-1 or dE-2
Factory Set Values
Ctr - 0001
SEC - 5A
dt1 - 15
dt2 - 30
CodE EnbL - no
CodE - 1234
Technical Features
Operating Voltage (Un) : 24 ... 250 V AC/DC
Frequency (Hz) : 45-65 Hz
Auxiliary Supply Power Consumption : < 4 VA
Measurement input power consumption : < 1VA
Iin : 0.005-5.5A~ (for X/5A)
0.005-1.1A~ (for X/1A)
Class : %0.5±1digit [(%10-%110) x full scale]
Current Transformer Ratio : 1 ... 1000 (for X/5A)
1 ... 5000 (for X/1A)
Ambient Temperature : -5°C; +70°C
Display : Red LED display
Dimension : PR-19
Equipment Protection Class : Double Insulation-Class II ( )
Box Protection Class : IP 54
Terminal Protection Class : IP 00
Box Material : Non-flammable
Installation :
Panel Mounted
Wire cross section (for terminal block) : 4 mm2
Weight :
0.34 kg
Installation Category : Class III
Panel Cut-outs : 91x91mm
Complies with EN-61010-1 standard.
Panel Cut-outs
91mm
91mm
Type PR 19 (96x96)
70mm
Wall 79.3mm
90mm
Type 19
50mm
Dimensions
70mm
79.3mm
90mm
Type PR 19 (96x96)
96mm
96mm
Connection Diagram
In order to activate the user password; in the measurement mode,
Press ESC button one by one until CAnC is displayed.
Press SET button while SAUEis displayed. (If you press ESC button
or select CAnC option instead of SAUE, new data is cancelled
and the previous data is set.)
Press SET button for 3 seconds (trF menu is displayed.)
Press SET button (EnbL menu is displayed.)
Press SET button, EnbL is displayed. (New value is entered but it is
not executed yet. In order to set the new value, please follow below
steps.)
By using UP/DOWN buttons, find SAUE
Activating the user password
This menu is used to activate the user password.
After activating the user password, if SET button is pressed for
3 seconds in order to enter to the menu, a user password is
required.
By using UP-DOWN-SET buttons, enter the
password. If you enter wrong password
device display shows Err message. In this
case press SET button then repeat
processes again.
Press SET button (Most left digit of display blinks)
By using UP/DOWN buttons, find CodE menu
By using UP/DOWN buttons, find yES
menu
In order to change the user password; in measurement mode,
Press SET button for 3 secs. (trF menu is displayed)
Press SET button (EnbL menu is displayed.)
By using UP/DOWN buttons, find CodE menu
By using UP/DOWN buttons, find CHnG menu.
By using UP-DOWN-SET buttons, enter
old password. If you enter wrong
password device display shows Err
message. In this case press SET button
then repeat processes again.
By using UP-DOWN-SET buttons, enter
new password.
By using UP-DOWN-SET buttons, enter
re-enter new password. If you enter
wrong password device display shows
Err message. In this case press SET
button then repeat processes again.
Press SET button (Most left digit of display blinks)
Press ESC button one by one until CAnC is displayed.
Press SET button while SAUEis displayed. (If you press ESC button or
select CAnC option instead of SAUE, new data is cancelled and the
previous data is set.)
By using UP/DOWN buttons, find SAUE
Press SET button, no is displayed.
Press SET button CHnG is displayed. (New value is entered but is not
executed yet. In order to set the new value, please follow below steps.)
User Password Settings
User password is set and activated in this menu. In order to
prevent the devices settings from unauthorized access, it is
necessary to set up a 4 digits user password and then activate
it. This menu has 2 submenus.
Changing the User Password
In this menu, user password can be changed.
Note: Factory set value for user password is 1234
A4451/Rev.2
PR-19
kl
KL
L
Un
6 A
Current
Measurement
Input Auxiliary
Supply
11 12
1 2
Autres manuels Ammeter Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur