Amdi PARTNER2 Manuel utilisateur
PARTNER2™ AUGMENTATIVE COMMUNICATION DEVICES
INSTRUCTION SHEET
Congratulations on your purchase of the PARTNER2™ Entry-Level Communicator. THE PARTNER2 IS AN ENTRY-LEVEL
AUGMENTATIVE COMMUNICATOR THAT OFFERS HIGH QUALITY,RELIABLE PERFORMANCE AND MANY IMPORTANT FEATURES FOR A VERY LOW
PRICE.PARTNER2 IS MANUFACTURED TO THE HIGHEST COMMERCIAL STANDARDS TO PROVIDE MANY YEARS OF RELIABLE OPERATION.WE
FULLY GUARANTEE THE PARTNER2’S OPERATION FOR A FULL YEAR,INCLUDING PARTS AND LABOR.*
DISTINCTIVE FEATURES OF THE PARTNER2
DROP RESISTANT,ABLE TO WITHSTAND ROUGH HANDLING.
WATER RESISTANCE FOR EASY CLEANING.
THE SHATTERPROOF CASE IS MADE OF A HIGH IMPACT PLASTIC.
LIGHT WEIGHT AND PORTABLE (LESS THAN 2LBS.)
THE PARTNER2 GIVES YOU “REAL-VOICE”HIGH QUALITY AUDIO REPRODUCTION.
MESSAGES CAN BE STORED FOR UP TO 100 YEARS WITH NO POWER.
IN ADDITION TO THE BUILT IN MICROPHONE,SPEAKER AND RECORD SWITCH,1OUTPUT AND 1INPUT JACK IS PROVIDED FOR EXTERNAL HOOK UPS.
INTERCHANGEABLE OVERLAYS,COMPATABLE WITH MAYER JOHNSON BOARDMAKER™ SOFTWARE EXTEND USABILITY.
*SEE WARRANTY AGREEMENT FOR DETAILS.
GENERAL OPERATION:
All controls are located on the back of the PARTNER2.
The PARTNER2 augmentative communicator is a self-contained communication device, which permits the user to record and playback 2
messages of 16 seconds in length. Graphic overlays (picture cards) can be easily changed by simply sliding the overlay between the housing grid
and the message square through the slot on the top of the grid. Simple to operate, just turn the unit on, adjust the volume, select and push the
picture to activate the corresponding message.
BATTERY INSTALLATION
1. Make sure that the PARTNER2 is turned off. Set VOLUME control switch fully to the right, until it clicks off.
2. Turn the PARTNER2 over and lay the front of the unit on a flat stable surface.
3. To gain access to the battery compartment and expose the batteries, remove the two screws holding down the plastic battery
cover on the left side of the bottom of the unit.
4. Remove the old batteries and discard them in accordance with your local recycling laws.
5. Install the new batteries observing the proper polarity and using 4 new AAA batteries.
6. Then replace the battery compartment cover by placing the cover over the access hole and tighten down the two screws. Insure
the battery cover is secure.
RECORD OPERATION:
Note: It is important during any recording operation that the built in microphone located at the back of the PARTNER2 is clear and
open. 1. Turn the PARTNER2 ON. Turn the VOLUME control switch to the left, until it clicks ON.
2. Set the VOLUME control, turning to the left, until it reaches the center of the range.
3. Depress and hold the built-in recording button. The recording button must be engaged for the entire recording process.
4. Select one of the 2 message squares on the face of the PARTNER2 and depress and hold down that message square, then begin
to say your message into the built-in microphone located at the back of the PARTNER2. For the best results, you should speak
directly into the microphone and be about 6 to 9 inches away from it in a quiet room.
5. The remaining message square can be programmed in the same manner.
INPUT AND OUTPUT JACKS:
The Partner2 comes fully equipped with 2 external control jacks (see diagram –BACK VIEW), 1 - Input and 1 - Output. The two control jacks
on the back of the unit correspond to the two message squares on the front of the Partner2.
INPUT JACK:
The first jack labeled J1 on the back of the Partner2 is an Input jack (see diagram –BACK VIEW for jack
locations). It is for activating the first message square on the left. When the switch plugged into the Input
jack is activated, the message programmed into that message square will play.
OUTPUT JACK: The jack labeled J2 on the back of the Partner2 is an Output jack used to control low
voltage DC devices.
When the second message square on the right is depressed, the corresponding jack labeled J2 is shorted and
a low voltage device plugged into that jack will be activated.
PLAYBACK OPERATION:
1. Turn the PARTNER2 ON. Turn the VOLUME control switch to the left, until it clicks ON.
2. Set the VOLUME control, turning to the left, until the desired playback volume is reached.
3. Select one of the 2 message squares on the face of the PARTNER2 and depress that message square for message playback.
OVERLAY DESIGN AND LAYOUT:
There are several methods you can use to make overlays for the PARTNER2.
1. Draw or print corresponding icons or words on a sheet of 3.75” by 4.75” paper.
2. Develop your custom overlay using Mayer Johnson’s BOARDMAKER™ Software.
CLEANING THE PARTNER2
Note: DO NOT SUBMURGE THE PARTNER2 IN WATER... THE PARTNER2 IS WATER RESISTANT - NOT WATER PROOF.
1. Turn the PARTNER2 off.
2. Remove the overlay from the switch grid.
3. With a wet wash cloth and mild soap wipe the soiled areas clean.
4. To rinse, use a wet sponge (cold water) and wipe away the soapy area. DO NOT SUBMURGE under the water and do not
allow water to enter the external speaker, record jacks or speaker holes.
Care and Maintenance
The PARTNER2 is designed to automatically power down after a message is played. However, the power down mode is still an active mode and
drains some power from the battery, affecting battery life. Therefore, if the PARTNER2 is not going to be used for a long period (2 to 3 hours) it
is recommended that the unit be turned off.
If the PARTNER2 fails to operate, or operates incorrectly, follow these steps
1. Check if the batteries are installed correctly.
2. Check if the PARTNER2 is ON and a Message has been recorded. Also make sure there are no obstacles blocking the message
membrane switch
3. Turn the PARTNER2 OFF for 15 Seconds, then back ON and retry playback.
4. Replace the Batteries.
5. For further assistance, feel free to contact our technical support team at 1-866-ERI-7255.
95 Sherwood Avenue Phone: (631) 531-8888 1-888-353-2634
Farmingdale, NY 11735 Fax: (631) 531-8811 http://www.admi.net
Table des matières
Autres manuels Amdi Jouet
