Amcrest A4-W Caractéristiques techniques

-1-

* Please read through the manual before using.

* To avoid a choking hazard, keep all small parts out of reach of small children.

* Never leave the drone unattended during battery charging.

* Never throw any batteries in a fire.

* Never fly the drone near other people.

* Keep all body parts away from the drone while the rotor blades are spinning.

Battery requirements for transmitter:

4 X 1.5V “AAA” size batteries (not included)

The drone is equipped with a Li-Poly rechargeable battery,

Please also pay attention to the following safety precautions:

* Do not leave the battery near a direct heat source such as fire or space heaters.

* Do not strike or throw the battery against any hard surface.

* Do not immerse the battery in water. Always store the battery in a cool dry place.

* When recharging the device, only use the battery charger intended for this product.

* Do not allow the battery to set on the charger for over 90 minutes.

* Do not operate your drone without a fully charged battery.

* Do not directly solder the battery to the device or pierce it with a nail or other sharp object.

* Do not transport or store the battery together with other metal objects.

* Never leave a charging battery unattended.

Note:

* Always dispose of old batteries responsibly

SKYVIEW DRONE MODEL A4-W

FLIGHT MANUAL

Safety Precautions

Flight Time: 7 minutes

Charge Time: 90 minutes

Allow the battery to charge fully before operation.

Find the Quick Flight Guide on Page 4

Video Tutorials: amcrest.com/a4drone

-2-

Battery Protection

Maintenance

Battery Installation & Charging

Controller

* Never try to repair circuitry. No serviceable circuitry are located inside the drone or transmitter.

* To avoid a choking hazard, keep all deteachable parts out of reach of small children.

* The drone is very powerful when taking off. Make sure to move the throttle forward gradually

to avoid it rising too quickly.

* After initial flight, turn off the drone first before you turn off the controller.

* Do not put the battery in high temperature or near extreme heat source.

* To avoid injury or damage, the drone should be flown 2 meters / 7 feet from people

or other obstacles.

* Children should only fly the drone under adult supervision. Always keep the drone

in clear sight while operating.

* Always make sure to turn off the power of the controller and drone when not in use.

The drone is equipped with low-voltage protection. When the batteries for the drone are low, the

internal programmed control system will automatically stop electrical supply to the drone’s rotors.

When the batteries are low, bring the drone to an area where you can begin charging the battery.

Allow the battery to charge fully before flying the device again.

* Clean the drone with a clean, dry soft cloth only.

* To avoid irreparable damage, keep the drone dry and away from water. Do not fly in

rainy conditions.

* Check the drone and accessories for any damage. If damage is found, do not use the

drone until it is repaired.

Battery installation should be done under adult supervision only!

Do not mix old and new batteries.

Do not mix different types of batteries.

To install the batteries: Open the cover of battery case, insert 4 X 1.5V AAA batteries,

according to indicated polarity (batteries not included).

Battery cover

4 X 1.5V AAA

batteries

Charging

Drone

Remove the battery from the drone and insert one side of the USB connector into the battery, and

the other side into any computer USB port.

The drone will come with a set of 4 replacement

rotor blades. These rotor blades will be denoted by two

different types; (A) type and (B) type rotors. You will see

the “A” and “B” letters on the canopy of the unit. When

replacing the blades of the device be sure to replace the

new blades into the rotors on the motor according to

their specific rotor types.

Throttle /Left Stick

Speed Select

Headless mode

Right Stick/Rudder

Go Back

Power light

Push in once to change

speed (Listen to beeps)

Slow speed - one beep

Medium speed - two beeps

High speed - three beeps

Press one time to unlock the drone

press again for slowly landing

Press for 3 seconds for emergency stop

Take picture/record video

Camera light

Press one time for taking picture,

press for 3 seconds for recording video

The light will flash while taking picture

and remian on while recording video.

Press once to go into headless mode,

press again to quit headless mode. For

more information on Headless mode refer

to the “Headless Mode” section of this manual.

-3-

360° Stunt Flip

Press down once (one beep

sounds) and then control rudder

to perform flip function

Trim button

Takeoff/Land

Trim buttons on the

controller are used to help

balance the drone while in

flight. For more information

on trim, refer to pg. 5

Allow the battery to charge fully before operation. A fully charged battery will provide

about 7 minutes of flight time per charge. When the green light on the battery disappears,

the battery will be fully charged and ready for use. Charging a battery should take no longer

than 90 minutes.

Power On/Off

Turns the controller

on/off.

Note: There are two ways you can operate the drone, one with the included controller and one

via the Amcrest SkyView app. For more information on how to setup your drone on the

Amcrest Skyview app refer to page 9.

Press once to automatically

direct the drone towards a

backwards direction.

Quick Flight Guide

Operation and Control

2. Hold the left stick/throttle

down on the controller.

Continue holding until the end

of step 3.

5. To pair the drone, move the

left stick/throttle up and down.

If successful, the LED lights

on the drone will stop flashing

and stay solid. If unsuccessful,

turn off each device and restart

from step 2.

6. After the drone is paired to

the controller, press the

takeoff/land button on the

top left of the controller to

start the motor.

To launch, move the left

stick/throttle up.

To land, press the takeoff/

land button.

3. Turn on the controller.

The power button is on the

bottom of the controller.

Release the left stick/throttle.

4. Turn on the drone. The

power button is on the

side of the drone.

Once the drone is turned on

the LED lights will begin to

flash indicating the drone is

ready to be paired to the

controller.

Rightside fly

Leftside fly

Rise

Drop

Up and down Forward and Backward

Left Spin and Right Spin Leftside and Rightside

Forward

Backward

-4-

Left Spin Right Spin

Press

The red LED lights indicate the front of the drone, the green LEDs

lights indicate the rear of the drone.

1. Place the drone onto a

level surface.

Trim Fine Tuning

Operation and Control

-5-

Forward/backward

fine-tuning

Leftside/rightside

fine tuning

Left/right spin

fine tuning

Backward

Trim

Forward

Trim

Leftside

Trim

Rightside

Trim

Backward

Trimmer

Forward

Trimmer

LeftSide

trimmer

RightSide

trimmer

Left spin

Trim

Right spin

Trim

Left Spin

trimmer

Right Spin

trimmer

Trim is used to balance the

drone while in flight.

Radical Flips & Rolls

Auto Calibration

Before you perform a flip or roll on your drone, make sure you have

enough space to prevent damage or injury to others.

-6-

You can perform flips and rolls with your drone in any speed setting.

To perform a flip or roll with your drone push in on the right stick/rudder. You will hear a click

and a beep will sound. Move the right stick/rudder in the direction you want to flip or roll.

To enable this function, turn on the drone and the controller.

Press the throttle and rudder sticks both to a 45° angle

as shown in the image to the right. Hold this position for 10

seconds and a light will flash on the drone.

Release the throttle and rudder. The lights on the drone

will remain on until thecalibration process is complete.

Press this button To quit this function.

(move in any direction)

Left flip

Right flip

Forward flip Backward flip

Push in on the right stick/rudder and

move it to the left.

Push in on the right stick/rudder and

move it to the right.

Push in on the right stick/rudder and

move it up. Push in on the right stick/rudder and

move the down.

While in flight, locate the Go Back button on your

controller and press the button once to initiate. Once

initiated, the drone will automatically be directed towards

a backwards direction.

To control the drone up and down when using the Go

Back function, use the Left Stick/Throttle. To cancel this

function, move the Right Stick/Rudder in any direction.

This is not a GPS drone. This feature will not return or land in its original

location when pressed. Keep your eyes on the drone when using this feature.

Go Back Function

Forward

Left Right

Backward

Headless Mode

HOW TO GET ENABLE/DISABLE HEADLESS MODE?

Press the button on controller(as shown in Figure A on the right)

when pressed you will hear a beep sound indicating the drone is in

headless mode. To quit headless mode, press it again and you will

hear another beep sound indicating that headless mode has been disabled.

HOW TO RECOGNIZE THE " FORWARD

SIDE" UNDER HEADLESS MODE?

When the drone initially takes off and the LED

lights on the device stop flashing the drone will

have its front side to the front direction of the controller.

The red LEDs on the drone indicate the front/forward side,

the green LEDs indicate the rear of the drone.

If you want to reset the orientation of headless mode,

you need to turn off the device and auto calibrate it.

-7-

Headless mode is used to align the drone’s movements to be

relative to the controller no matter which way the drone is facing.

Figure A.

-8-

Camera:

Normal camera:

HOW TO REVIEWING PHOTOS/VIDEOS ON A COMPUTER

Insert the microSD card into device.

The drone comes equipped with a built-in 720p (1280*720) camera which can be used

to record data during flight. This camera is located on the front side of the drone. To store

data retained during flight, the drone also has a built-in microSD card slot which can support

up to a 32GB microSD card. All data retained by the device will be stored via a microSD card

and can be viewed via a mobile device or computer.

To review photos and videos, please insert one end of

the data cable into the USB port of the drone. Insert

the other end into a USB port on the computer. Open

"File Explorer" and locate the related file from which

you can view photos and videos.

Note: The drone is not compatible

with microSD cards aboce 32GB

To record video while using the drone’s controller, you must enable record mode on the drone.

Record mode can be enabled by flying the drone or by pressing and holding the Photo/Video

button, located on the top right corner of the drone’s controller for 3 seconds.

Once recording mode has been enabled, press and hold the Photo/Video button for 3 seconds

to start recording video. Once recording has begun, the drone will have a flashing blue light on

the bottom. This indicates the drone is actively recording video. To store the recording, you must

end the recording. If you do not end the recording properly the footage will not be saved to the

microSD card.

To end a recording, press and hold the Photo/Video button again for 3 seconds. This will stop

the drone from recording video. Once a recording has been stopped the flashing blue light will

disappear and a solid red light will be visible on the bottom of the drone. Once the recording has

been stopped, the footage will be saved to the microSD card and will be available to review.

Recording/Snaphot

Photo/Video Button

1. SOFTWARE DOWNLOAD AND INSTALLATION

2. USING INSTRUCTION

1). Insert a fully charged battery into the drone and turn it on. (The power button is on the

side of the drone.)

2). The drone will begin to flash red and green indicating the drone is ready to be synced.

3). To sync the drone to the app, go to “Settings” on your mobile device and enable WI-FI.

4). Locate the hotspot network for your drone. It will be labeled, “SKYVIEW 720P XXXXXX”.

5) Tap on the network and allow your mobile device to connect to the hotspot for your drone.

6). Open the Amcrest SkyView app and tap the “FLY” icon on the main menu to access

begin flying.

- Search ‘Amcrest SkyView’ from App Store or Google Play Store.

- Download and install it to your mobile device.

-9-

2. Tap on the

Launch button in the

lower left hand

corner of the screen

to start the drone.

(The rotor blades will

begin to spin.)

3. Use the forward

throttle button to launch

the drone. (For more

information on flight

controls, refer to the

flight controls section of

the manual.)

4. When you are

ready to land the

drone, find a clear,

safe place to land and

tap on the Landing

button. (To perform an

emergency landing,

press the STOP

button.

Launch Functions

1. Make sure the

drone is placed

on a level

surface.

App User Guide

Throttle

- Use throttle to initially launch the

drone. Moves the drone upward.

2. Throttle Down - Moves the drone downward.

Rotate Left

- Rotates the drone head to the

left.

Rotate Right

- Rotates the drone head to the

right.

Forward - Moves the drone forward.

Back

- Moves the drone backward.

Move Left

- Moves the drone to the left.

Move Right

- Moves the drone to the right.

9. Forward Trim - Used to balance the drone

while flying in a forward direction.

10. Backward Trim - Used to balance the

drone while flying in a backward direction.

11. Left Rotate Trim - Used to balance the

drone when performing a left rotation.

12. Right Rotate Trim - Used to balance the

drone when performing a right rotation.

13. Left Trim - Used to balance the drone

when performing a left turn.

14. Right Trim - Used to balance the drone

when performing a right turn.

15. Launch - Used to start the motor on the

drone.

16. Stop - Used as an emergency stop. Will

stop the drone completely while in operation.

17. Landing - Used to land the drone while in

flight.

3478

-10-

Flight Controls

Table des matières

Autres manuels Amcrest Drone

Amcrest

Amcrest OB1-M Manuel utilisateur

Manuels Drone populaires d'autres marques

Ryze

Ryze Tello Manuel utilisateur

PowerVision

PowerVision PowerRay Manuel utilisateur

Force1

Force1 rogue F72 Manuel utilisateur

Zerotech

Zerotech DOBBY Manuel utilisateur

Protocol

Protocol VIDEODRONE AP Manuel utilisateur

dji

dji Matrice M210 Manuel utilisateur

MAKE

MAKE Terry Kilby Manuel utilisateur

SYMA

SYMA X440 Manuel utilisateur

RUKO

RUKO F11 Manuel utilisateur

SYMA

SYMA X5UW(720P) Manuel utilisateur

Dynali

Dynali 25 H Mode d’emploi

dji

dji PHANTOM 4 Manuel utilisateur

Atlas

Atlas AtlasPRO Manuel utilisateur

Twodots

Twodots TVVIN BOARD Manuel utilisateur

GDU

GDU SAGA Manuel utilisateur

Ares

Ares ETHOS QX 130 Manuel utilisateur

Walkera

Walkera ZHUN Manuel utilisateur

dji

dji WIND-4 Manuel utilisateur