Amada AH Series Manuel utilisateur
Z07M0875E-07
OPERATION MANUAL
WELDING HEAD
AH Series
AH Series
Thank you for purchasing our Welding Head AH Series.
This operation manual describes its method of operation and precautions for use.
Read this operation manual carefully prior to use. Store appropriately for ready reference.
Contents
1. Special Precautions
(1) Safety Precautions....................................................................... 1
(2) Precautions for Handling.............................................................. 4
2. Features ........................................................................................... 5
3. Installation and Connection
(1) Installation ................................................................................... 6
(2) Connection .................................................................................. 7
4. Operating Method
(1) Stroke and Welding Force Adjustments........................................ 8
(2) Adjustment of Cylinder Descending Speed .................................. 9
(3) Lower Electrode Alignment .......................................................... 10
(4) Adjustment of the Timing to Start a Welding Current Flow............ 10
(5) Pressure Diagram........................................................................ 11
(6) Maintenance Management........................................................... 11
5. Product Specifications
(1) Specifications............................................................................... 12
(2) Welding Cable ............................................................................. 13
6. Outline Drawings ............................................................................. 14
-1-
AH Series
1. Special Precautions
1. Special Precautions
Before using, be sure to read this
operation manual to operate this
machine correctly. This operation
manual may include some items that do
not correspond to your use. However,
you are kindly requested to read only
the items related to your use.
(1) Safety Precautions
These precautions are shown for safe
use of our products and for
prevention of damage or injury to
operators or others. Be sure to read
each of them, since all of them are
important for safety.
The meaning of the words and
symbols is as follows.
！DANGER
Denotes operations and practices that
may imminently result in serious injury
or loss of life if not correctly followed.
！WARNING
Denotes operations and practices that
may result in serious injury or loss of
life if not correctly followed.
Denotes operations and practices
that may result in personal injury or
damage to the equipment if not
correctly followed.
！CAUTION
These symbols denote
“prohibition”.
They are warnings
about actions out of
the scope of the
warranty of the product.
！These symbols denote
actions which
operators must take.
Each symbol represents
the contents that give
notice of DANGER,
WARNING, or
CAUTION to the
operator.
-2-
AH Series
Otherwise, an electric shock or injury will occur. When
internal inspection or repair is required, make contact with us.
Do not disassemble, repair, or modify this machine in
any case.
！DANGER
！
！
！
！WARNING
When welding, keep your fingers and hands away from
the electrodes.
Do not put your hands between the electrodes.
The welded part of a workpiece, electrodes and electrode
holder are very hot. Do not touch them; otherwise you may
be burnt.
Do not touch any welded part or electrodes during
welding and just after welding finished.
Application of a voltage out of the specified range can
cause fire and electric shock.
Apply the specified power supply.
Continuous operation after occurrence of a trouble such as
burning smell, abnormal sound, abnormal heat, smoke, etc. can
cause electric shock and fire. If such a trouble occurs,
immediately consult us or your distributor.
Stop the operation if any trouble occurs.
The welding machine generates a magnetic field and has
effects on the operation of the pacemaker while it is turned on.
A person who uses a pacemaker must not approach the
welding machine or walk around the welding shop while the
welding machine is in operation, without being permitted by
his/her doctor.
Persons with pacemakers must stay clear of the welding
machine.
If you look at the surface flash and expulsion directly
during welding, your eyes may be damaged.
Wear protective glasses.
1. Special Precautions
-3-
AH Series
！
！
！
！
！
！CAUTION
Water splashed over the electric parts can cause electric
shock and short circuits.
Do not splash water on the product.
Do not bend, pull, or pinch any cable forcibly. If the cable is
damaged, it will cause an electric shock, short circuit, or firing.
Do not give excessive force to connecting cables.
Cables of insufficient current-carrying capacities and loose
connections can cause fire and electric shock.
If the welding cable is not connected completely, a spark will occur.
Connect the specified cables securely.
If the product falls or drops, injury may result.
Install the product on firm, level surface.
Do not put any combustible material around the welder. Surface
flash and expulsion can ignite combustible matter.
Keep combustible matter away from the welding machine.
If such a cover is used, it may be overheated and burn.
Do not cover the product with a blanket, cloth, etc.
Keep a fire extinguisher in the welding shop in case of fire.
Keep a fire extinguisher nearby.
Maintain and inspect the product periodically, and repair any
damage near by before starting operation. Tighten the welding
cable connecting section periodically.
Maintain and inspect the product periodically.
Put on protective gear such as protective gloves, long-sleeve
jacket, leather apron, etc. Surface flash and expulsion can burn
the skin if they touch the skin.
Protective gear must be worn.
Use of this product in a manner other than specified can cause
electric shock and fire.
Do not use this product for purposes other than welding.
After a recovery from the outage, the machine may be started or
powered suddenly, resulting in an injury.
When outage occurs, be sure to turn off the power supply.
1. Special Precautions
-4-
(2) Precautions for Handling
Do not install this product in the following:
-Damp places where humidity is higher than 90%,
- Dusty places,
- Places where chemicals are handled,
- Places where corrosive gas is generated,
- Places near a high noise source,
- Hot or cold places where temperatures are above 40C or below 5C, and
- Areas where water will be condensed.
Set the cylinder cover on when operating the cylinder to avoid fingers to be
caught in the cylinder stopper.
In this machine, the linear guide (linear bushing) is used vertically. Accordingly,
grease or oil may drip, but this is not an accident. In particular, when a new
machine is used, lots of grease of oil will drip. In this case, wipe it off properly
during machine operation. If grease or oil sticks on the weldment, this may cause
a defect.
AH Series
Clean the outside of the product with a soft, dry cloth or one wet with a little
water. If it is very dirty, use diluted neutral detergent or alcohol. Do not use paint
thinner, benzine, etc., since they can discolor or deform the product.
Between electrodes, do not put such a material other than the weldment as tool
and screw. Otherwise, the welding electrode will be damaged or a spark will
occur. When performing maintenance for this machine as a result of replacement
of electrodes, turn off the power supplies of the welder and control device in
advance.
Do not put a screw, a coin, etc., in the product, since they can cause a
malfunction.
Be sure to install the screws, which were removed for maintenance of this
machine, in their original positions. If they are installed in different positions, this
machine will be damaged or go wrong.
Operate the product according to the method described in this operation manual.
1. Special Precautions
-5-
AH Series
2. Features
In AH series welding heads, the air cylinder and the pressure follow-up mechanisms are
integrated into signal housing for compact design.
The AH series welding heads offer great quality of welding by improving the accuracy and
reliability, and ease of mounting onto the automatic welding machine.
2. Features
Drill some holes to mount the welding head on the mounting surface of your existing desk,
shelf, or bench as shown below.
Mounting Base Mounting Frame
Note: For installation without a base, the mounting surface must have an enough structural
strength.
-6-
AH Series
3. Installation and Connection
(1) Installation
3. Installation and Connection
ABCDEFGH I J M N
70 180 450 10 160 270 160 145 122 226 For 6-M10 For M10
Center of
electrode
(1) Air Piping
The speed controller with one-touch joint is mounted at the main unit of cylinder. The outer
diameter of urethane tube is φ10.
(2) Connection of the Welding Cable
Connect the bus bar on the rear of the welding head to the welding transformer with a
welding cable of adequate square millimeter.
(3) Connection of the Pressure Signal Cable
Connect the terminal or connector of the pressure signal cable to the welding power supply.
Note: See also the operation manual for the welding power supply.
-7-
AH Series
(2) Connection
3. Installation and Connection
-8-
Home (Released) Touch Press
A = B + C
Full stroke Stroke to touch Stroke to press
AH Series
4. Operating Method
4. Operating Method
(1) Stroke and Welding Force Adjustments
Rod
Stopper spacer
Cylinder rod
Lock nut
Adjustment nut
Scale
Workpiece
Table des matières
Autres manuels Amada Système de soudage
Amada
Amada TCW Manuel utilisateur
Amada
Amada MA-520B Manuel utilisateur
Amada
Amada UB25 Manuel utilisateur
Amada
Amada MacGregor PA20P Series Manuel utilisateur
Amada
Amada Miyachi Unitek STA-200A Manuel utilisateur
Amada
Amada ML-2550A Manuel utilisateur
Amada
Amada ML-2050A-CE Manuel utilisateur
Amada
Amada TC-W100A Manuel utilisateur
Amada
Amada MH-1H-01 Manuel utilisateur
Amada
Amada TL-180B Manuel utilisateur
Amada
Amada ML-2450A-CE Manuel utilisateur
Amada
Amada MF-C300A-SF Manuel utilisateur
Amada
Amada ST-100A Manuel utilisateur
Amada
Amada ML-3030AS Manuel utilisateur
Amada
Amada HF28/240 Manuel utilisateur
Amada
Amada MH-D500D Manuel utilisateur
Amada
Amada MF-C2000A Series Manuel utilisateur
Amada
Amada MA-650A Manuel utilisateur
Amada
Amada MA-660A Manuel utilisateur
Amada
Amada ML-2350AF-CDRH Manuel utilisateur
Manuels Système de soudage populaires d'autres marques
TAFA
TAFA 30*8B35 Manuel utilisateur
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur
ESAB
ESAB Buddy Arc 145 Manuel utilisateur
CIGWELD
CIGWELD 636804 Guide rapide
Red-D-Arc
Red-D-Arc DC-400 Manuel utilisateur
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur
