Amada PU-G Manuel utilisateur

Z08M0896E-06

OPERATION MANUAL

HAND-HELD WELDING HEAD

PU-G

Thank you for purchasing our Hand-Held Welding Head PU-G.

This operation manual describes its method of operation and precautions for use.

Read this operation manual carefully prior to use. Store appropriately for ready reference.

Contents

1. Special Precautions

(1) Safety Precautions....................................................................... 1

(2) Precautions for Handling.............................................................. 4

2. Features ........................................................................................... 5

3. Name and Functions of Each Section ............................................ 6

4. Connecting the Pressure Signal Cable .......................................... 8

5. Operating Method ............................................................................ 9

6. Product Specifications .................................................................... 10

7. Outline Drawings ............................................................................. 11

-1-

PU-G

1. Special Precautions

Before using, be sure to read this

operation manual to operate this

machine correctly. This operation

manual may include some items that do

not correspond to your use. However,

you are kindly requested to read only

the items related to your use.

(1) Safety Precautions

These precautions are shown for safe

use of our products and for prevention of

damage or injury to operators or others.

Be sure to read each of them, since all

of them are important for safety.

The meaning of the words and

symbols is as follows.

！DANGER

Denotes operations and practices that

may imminently result in serious injury

or loss of life if not correctly followed.

！WARNING

Denotes operations and practices that

may result in serious injury or loss of

life if not correctly followed.

Denotes operations and practices

that may result in personal injury or

damage to the equipment if not

correctly followed.

！CAUTION

These symbols denote

“prohibition”.

They are warnings

about actions out of

the scope of the

warranty of the product.

！These symbols denote

actions which

operators must take.

Each symbol represents

the contents that give

notice of DANGER,

WARNING, or

CAUTION to the

operator.

-2-

PU-G

Otherwise, an electric shock or injury will occur. When

internal inspection or repair is required, make contact with us.

Do not disassemble, repair, or modify this machine in

any case.

！DANGER

！

！WARNING

When welding, keep your fingers and hands away from

the electrodes.

Do not put your hands between the electrodes.

The welded part of a workpiece, electrodes and electrode

holder are very hot. Do not touch them; otherwise you may

be burnt.

Do not touch any welded part or electrodes during

welding and just after welding finished.

Application of a voltage out of the specified range can

cause fire and electric shock.

Apply the specified power supply.

Continuous operation after occurrence of a trouble such as

burning smell, abnormal sound, abnormal heat, smoke, etc. can

cause electric shock and fire. If such a trouble occurs,

immediately consult us or your distributor.

Stop the operation if any trouble occurs.

The welding machine generates a magnetic field and has

effects on the operation of the pacemaker while it is turned on.

A person who uses a pacemaker must not approach the

welding machine or walk around the welding shop while the

welding machine is in operation, without being permitted by

his/her doctor.

Persons with pacemakers must stay clear of the welding

machine.

If you look at the surface flash and expulsion directly

during welding, your eyes may be damaged.

Wear protective glasses.

1. Special Precautions

-3-

PU-G

！

！CAUTION

Water splashed over the electric parts can cause electric

shock and short circuits.

Do not splash water on the product.

Do not bend, pull, or pinch any cable forcibly. If the cable is

damaged, it will cause an electric shock, short circuit, or firing.

Do not give excessive force to connecting cables.

Cables of insufficient current-carrying capacities and loose

connections can cause fire and electric shock.

If the welding cable is not connected completely, a spark will occur.

Connect the specified cables securely.

If the product falls or drops, injury may result.

Install the product on firm, level surface.

Do not put any combustible material around the welder. Surface

flash and expulsion can ignite combustible matter.

Keep combustible matter away from the welding machine.

If such a cover is used, it may be overheated and burn.

Do not cover the product with a blanket, cloth, etc.

Keep a fire extinguisher in the welding shop in case of fire.

Keep a fire extinguisher nearby.

Maintain and inspect the product periodically, and repair any

damage near by before starting operation. Tighten the welding

cable connecting section periodically.

Maintain and inspect the product periodically.

Put on protective gear such as protective gloves, long-sleeve

jacket, leather apron, etc. Surface flash and expulsion can burn

the skin if they touch the skin.

Protective gear must be worn.

Use of this product in a manner other than specified can cause

electric shock and fire.

Do not use this product for purposes other than welding.

After a recovery from the outage, the machine may be started or

powered suddenly, resulting in an injury.

When outage occurs, be sure to turn off the power supply.

1. Special Precautions

-4-

(2) Precautions for Handling

Do not install this product in the following:

-Damp places where humidity is 90% or higher,

- Dusty places,

- Places where chemicals are handled,

- Places where corrosive gas is generated,

- Places near a high noise source,

- Hot or cold places where temperatures are above 40C or below 5C, and

- Areas where water will be condensed.

Caution must, therefore, be made against damage that could happen if subjected

to heavy shock such as when dropped down.

PU-G

Clean the outside of the product with a soft, dry cloth or one wet with a little

water. If it is very dirty, use diluted neutral detergent or alcohol. Do not use paint

thinner, benzine, etc., since they can discolor or deform the product.

Between electrodes, do not put such a material other than the weldment as tool

and screw. Otherwise, the welding electrode will be damaged or a spark will

occur. When performing maintenance for this machine as a result of replacement

of electrodes, turn off the power supplies of the welder and control device in

advance.

Do not put a screw, a coin, etc., in the product, since they can cause a

malfunction.

Be sure to install the screws, which were removed for maintenance of this

machine, in their original positions. If they are installed in different positions, this

machine will be damaged or go wrong.

Operate the product according to the method described in this operation manual.

1. Special Precautions

Welding with large electric current may cause the body of this unit and welding

cable to get heated. In such case, consult our sales person for help.

Be careful so that no horizontal load should be applied to this hand-set. Take

note that the following cases may possibly occur by chance.

- Normal pressure force is not obtained.

- Damage or bend of electrode and/or main shaft.

-5-

PU-G

2. Features

Grip-held push type hand-set

Free point welding irrespective of welded object

Pressurization for stable welding

2. Features

-6-

PU-G

3. Name and Functions of Each Section

-7-

PU-G

3. Name and Functions of Each Section

(1) Pressure adjusting knob

This knob is used to adjust the pressure at welding. Turn the pressure knob to set

the required pressure.

(2) Pressure scale

This scale is used to read the pressure at welding. For the relation of pressure

between "Pressure scale" and "Pressure spring specification", refer to the pressure

diagram (page 13).

CAUTION The pressure diagram represents theoretical values. To measure actual

pressure, use a pressure gauge or spring balance.

(3) Pressure sensor

The pressure sensor is used to make sure that pressure is applied to the weldment

at welding. This sensor outputs a signal when the electrode makes contact with the

weldment and the specified pressure is reached.

(4) Pressure spring

This pressure spring gives the pressure required for welding to the weldment.

Pressure spring specification (S series): Maximum pressure 25/50/80/120 (N)

(5) Electrode holder

This part is used to give a welding current to the welding electrodes and fix the

electrodes.

(6) Welding electrode

This is an electrode rod for welding. Select a material and an end shape suitable for

your use. We prepare welding electrodes for various uses.

(7) Welding electrode fixing screw

This screw is used to remove or mount the welding electrode.

(8) Screw to supply power (from the transformer or power supply side)

Connect the welding cable from the welding transformer or welding power supply.

！

-8-

PU-G

4. Connecting the Pressure Signal Cable

LS.

COM

[Pressure signal cable terminal]

Microswitch

(WT)

(BK)

2: BK (COM) 1: WT (NC)

2P connector

Selecting F terminal

Selecting 2P connector

COM.

Table des matières

Autres manuels Amada Système de soudage

Amada

Amada ML-2050A-CE Manuel utilisateur

Amada

Amada ML-2350AF Manuel utilisateur

Amada

Amada MH-D500D Manuel utilisateur

Amada

Amada HF-2500A Manuel utilisateur

Amada

Amada MA-520B Manuel utilisateur

Amada

Amada ML-2350A-CE Manuel utilisateur

Amada

Amada Delta Manuel utilisateur

Amada

Amada ML-2550A Manuel utilisateur

Amada

Amada ML-2650B Manuel utilisateur

Amada

Amada ML-3060AS Manuel utilisateur

Amada

Amada ML-7 Series Manuel utilisateur

Amada

Amada IPB-5000B Manuel utilisateur

Amada

Amada MF-C300A-SF Manuel utilisateur

Amada

Amada UB25 Manuel utilisateur

Amada

Amada MA-650A Manuel utilisateur

Amada

Amada MA-660A Manuel utilisateur

Amada

Amada MD Series Manuel utilisateur

Amada

Amada LW500A Manuel utilisateur

Amada

Amada AH Series Manuel utilisateur

Amada

Amada MH-H500D Manuel utilisateur

Amada

Amada TCW Manuel utilisateur

Amada

Amada EZ-AIR Manuel utilisateur

Amada

Amada TL-180B Manuel utilisateur

Amada

Amada HF28/240 Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur