ALTAI C2s Manuel utilisateur
Altai Technologies Ltd. All rights reserved
Altai C2s Dual-Band 2x2
802.11ac WiFi A /Bridge
Installation Guide
Version 1.0
Date: May, 2016
ii
Altai Technologies Ltd. All rights reserved
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
Copyright © 2016 Altai Technologies Limited
ALL RIGHTS RESERVED.
Altai echnologies Limited
Unit 209, 2/F, Lakeside 2,
10 Science ark West Avenue,
Hong Kong Science ark,
Shatin, New Territories,
Hong Kong
Telephone: +852 3758 6000
Fax: +852 2607 4021
Web: www.altaitechnologies.com
Customer Support Centre:
Email: [email protected]
iii
Altai Technologies Ltd. All rights reserved
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
Federal Communication Commission (FCC) – USA
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to art 15 of the FCC Rules; these
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
This device complies with art 15 of FCC Rules. Operation is subject to
the following conditions. (1) This device may not cause harmful
interference. (2) This device must accept any interference received,
including interference that may cause undesired operation.
This device should not be co-located or operating in conjunction with
any other antenna or transmitter.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
FCC Radiation Exposure Statement: The user is advised to keep a
distance of at least 45cm from the device when it is in operation.
European Conformity (CE) – EU
This is a Class B product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
iv
Altai Technologies Ltd. All rights reserved
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
Warning
C2s may require professional installation depending on the deployment
scenario.
Only use the power adaptor supplied with C2s. Using a different power
adaptor might damage C2s.
Install a lightning arrestor to protect the A for lightning dissipation
during rainstorms. Lightning arrestors are mounted outside the structure
and must be grounded by means of a ground wire to the nearest
ground rod or item that is grounded.
Disclaimer
All specifications are subject to change without prior notice. Altai
Technologies assumes no responsibilities for any inaccuracies in this
document or for any obligation to update information in this
document. This document is provided for information purposes only.
Altai Technologies reserves the right to change, modify, transfer, or
otherwise revise this publication without notice.
v
Altai Technologies Ltd. All rights reserved
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
able of contents
able of contents .............................................................................................. v
1. Introduction ................................................................................................ 1
2. Field Installation ......................................................................................... 2
2.1.
U
N ACK THE SHI MENT
....................................................................................................... 2
2.2.
H
ARDWARE
O
VERVIEW
...................................................................................................... 3
2.3.
RE ARATION FOR
I
NSTALLING
C2
S
.................................................................................... 6
2.4.
C
ABLE
F
EED
-T
HROUGH
...................................................................................................... 6
2.5.
M
OUNTING
O
TIONS
......................................................................................................... 7
2.6.
OWER
O
TIONS AND
C
ABLE
C
ONNECTION
I
NSTRUCTIONS
................................................. 8
2.7.
C2
S
W
ATER ROOF
ROTECTION
........................................................................................ 9
3. Electrical and Lightning Protection ....................................................... 11
3.1.
S
URGE
ROTECTOR
.......................................................................................................... 11
3.2.
L
IGHTNING
ROTECTION
S
YSTEM
....................................................................................... 11
3.3.
LAN
C
ABLE FOR
O
UTDOOR
I
NSTALLATION
........................................................................ 11
1
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
Altai Technologies Ltd. All rights reserved
1.Introduction
This guide is designed to provide the information needed to mount
Altai C2s Super WiFi A /Bridge at the site location.
The document is applicable for hardware platform C2s and the
following model.
roduct Name: C2s Dual-Band 2x2 802.ac WiFi AP/Bridge
Model Number: C2-2221-000
It is assumed in this document that a site survey has been performed
before the site installation. The appropriate antenna pole and A
locations have been selected. It is a good practice to have a
document which consists of a map and drawing illustrating the A and
poles locations. A planning on I network is also an important issue for
network planning.
The user may need to refer the following document during C2s
installation and Configuration.
[1] C2s Dual-band 2x2 802.11ac Wi-Fi A /Bridge Configuration Guide
[2] C2s Dual-band 2x2 802.11ac Wi-Fi A /Bridge Data Sheet
2
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
Altai Technologies Ltd. All rights reserved
2.Field Installation
2.1. Unpack the shipment
Check the equipment and the installation kits against the packing list to
ensure that the equipment part numbers, parts, and the ancillary
equipment included in the shipment match what is specified on the
packing list. The shipment consists of a C2s Super WiFi A /Bridge and an
installation kit in the container. If there is any difference from the
packing list, you may need to contact the sales representative.
Inspect the equipment to see if there is any shipping damage. If it does
have any damage, you can contact the sales representative for repair
or replacement.
C2s standard package contents include:
A. C2s Main Unit x 1
B. DC Injector x 1
C. AC Adapter x 1
D1. US lug x 1
D2. UK lug x 1
D3. EU lug x 1
E. Cable Tie x 2
F. Mounting Screw x 2
G. Mounting Anchor x 2
A
B
C
D1
D2
D3
E
F
or
or
G
3
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
Altai Technologies Ltd. All rights reserved
LED anel
Back Mount Base
Mounting Holes
(For Wall Mount Option)
2.2. Hardware Overview
Front View
Back View Side View
Front anel (2.4G and 5G
antennas embedded)
Lower Compartment
(Housing for Ethernet orts)
Sliding Cover for the
Lower Compartment
Mounting Slots
(For ole Mount Option)
4
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
Altai Technologies Ltd. All rights reserved
LED Panel
Power
Solid Yellow: ower on
Off: No ower
Received Signal Strength
(Station/Repeater/Bridge
2.4G/5G Radio WiFi
(AP/S A/Repeater/Bridge Mode)
Solid Green:
1. A Mode on but with no Clients Associated
2. STA/Repeater Mode on but not connected to A
3. Bridge Mode on but not connected to Remote eer
Flashing Green: A Mode with at least one Client
Associated for Data Transmitting/Receiving
Off: Radio Disabled
LAN (Ethernet 0/1)
Solid Blue/Green: LAN Connected
(Blue for 1Gbps; Green for 100/10Mbps)
Flashing Blue/Green: Data
Transmitting/Receiving
Off: LAN Disconnected
Flashing Yellow: A Booting Up
5
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/Bridge
Installation Guide
Altai Technologies Ltd. All rights reserved
Ethernet Ports and Reset Button
E H0/PoE IN:
It is used to connect to power source (see the ower Options in the
following section) and provides 10/100/1000 Mbps network interface for
LAN connection.
E H1:
It provides 10/100/1000 Mbps network interface for LAN connection
with peripherals.
Reset Button:
It serves two functions for C2s operation:
•Reboot: ress and hold the Reset Button for 2-3 seconds until the
Power LED blink once.
•Factory Reset: ress and hold the Reset Button for 5-8 seconds until
the Power LED blink twice consecutively.
Eth ort 1
Reset Button
Eth ort 0
0s
2-3s
5-8s
ower LED
Reboot Factory Reset
Autres manuels pour C2s
1
Table des matières
Autres manuels ALTAI Point d'accès sans fil
ALTAI
ALTAI CX200 Manuel utilisateur
ALTAI
ALTAI A3 Series Manuel utilisateur
ALTAI
ALTAI A2N Feuille d'instructions
ALTAI
ALTAI A2 Manuel utilisateur
ALTAI
ALTAI IX500 Manuel utilisateur
ALTAI
ALTAI AX500 Series Manuel utilisateur
ALTAI
ALTAI A2C Manuel utilisateur
ALTAI
ALTAI A175FD Manuel utilisateur
ALTAI
ALTAI C2s Manuel utilisateur
ALTAI
ALTAI CX200 Manuel utilisateur
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
