ALTAI A2C Manuel utilisateur
1
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Altai A2c Indoor Dual-
Band 2x2 802.11ac AP
_________________________________________________
Quick Setup Guide
Version 1.0
2
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Introduction
Thank you for purchasing the Altai A2c. This guide provides instructions to
install the product and set it up as AP with minimal effort.
Package Contents
T-Rail Mounting Kit
A2c Main Unit
Quick Setup
Guide
PoE Injector
(Optional Item)
Ceiling Mounting Kit
15/16in T-Rail Clip x 2
9/16in T-Rail Clip x 2
Spacer x 2
P2.6*10 Screw x 2
P2.6*25 Screw x 2
Mounting Bracket x 1
Mounting Screw x 2
P3.5*32 Screw x 2
P2.6*12 Screw x 2
3
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Hardware Overview
LED Panel
Ethernet Ports and Reset Button
0s
2-3s
5-8s
Power LED
Reboot
Factory Reset
ETH/PoE IN:
It is used to connect to power source (see
the Power Options in the following section)
and provides 10/100/1000 Mbps network
interface for LAN connection.
Reset Button:
It serves two functions:
Reboot: Press and hold the Reset Button
for 2-3 seconds until the Power LED blink
once.
Factory Reset: Press and hold the Reset
Button for 5-8 seconds until the Power LED
blink twice consecutively.
Power
Solid Orange: Power on
Off: No Power
LAN (Ethernet)
Solid Blue: LAN Connected
Flashing Blue: Data
Transmitting/Receiving
Off: LAN Disconnected
2.4G/5G Radio WiFi
(AP/Repeater/Bridge Mode)
Solid Blue (2.4G) / Green (5G):
1. AP Mode on but with no Clients
Associated
2. Repeater Mode on but not
connected to AP
3. Bridge Mode on but not connected
Flashing Blue/Green: Data
Transmitting/Receiving
Off: Radio Disabled
Solid Blue: Remote Management Mode
Off: Standalone Mode
Operation Mode
ETH/PoE IN
Reset Button
4
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
P2.6*10 Screw
Clip
Wall
Mounting Screw
Mounting Bracket
P2.6*12 Screw
P3.5*32 Screw
Mounting Options
Option 1: Ceiling Mount –Mounting bracket
1. Attach the mounting bracket to the ceiling using the provided mounting
screws and long screws (P3.5*32).
2. Insert the provided short screws (P2.6*12) into the bottom cover of A2c.
Make sure that the screws are exposed enough to attach the mounting
bracket.
3. Install the A2c on the mounting bracket by rotating the unit clockwise
about 90 degrees to secure it in place.
Option 2: Ceiling Mount - T-Rail clips
1. Attach the small T-Rail clips to the bottom cover of A2c using the provided
short screws (P2.6*10).
If extra space is required, use the provided spacers and large T-Rail clips
with long screws (P2.6*25).
2. Line up the connected T-Rail clips with an appropriately sized rail and
press the unit onto the rail until it snaps into place.
Lock A2c by revolving
P2.6*25 Screw
Clip
Spacer
T-Rail
Clips
OR
5
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Setup Requirements and Preparation
A computer with Web Browser: Google Chrome, Mozilla Firefox, or
Microsoft Internet Explorer 8 (or above)
Two Cat 5e/6 Ethernet cables
AltaiCare account (Optional) for cloud management service
Power Options and Cable Connection Instructions
You can follow one of the options below for A2c configuration as described
in the following sections.
1. Connect A2c Ethernet port to a PoE
Injector’s “PoE” port with an Ethernet
Cable.
2. Connect a computer to the PoE
Injector’s “LAN” port with another
Ethernet Cable.
3. Connect the PoE Injector to AC
power socket using a power cord
(Not provided in the package).
4. Make sure the Power LED light is
orange and the LAN LED light is blue.
1. Connect A2c Ethernet port to an
802.3at PoE Switch with an Ethernet
Cable.
2. Connect a computer to the switch.
3. Make sure the Power LED light is
orange and the LAN LED light is blue.
Option 2: PoE Injector (Ordered separately)
Option 1: 802.3at-compliant PoE switch
PoE
LAN
802.3at –Compliant
PoE Switch
6
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
1. Change TCP/IP Setting on your computer
For Windows 7 users,
1. Go to Control Panel, click Network and Sharing Center and then choose
the adapter that you want to connect to A2c unit. In this example,
adapter “Local Area Connection 2” is in connection with A2c. Click it and
then click Properties.
2. Under the Networking tab, click Internet Protocol Version 4 (TCP/IPv4) in
the list box “This connection uses the following items”, and then click
Properties.
3. Type in the following IP address and Subnet mask:
IP address: 192.168.1.2
Subnet mask: 255.255.255.0
4. Click OK to close the Internet Protocol Version 4 (TCP/IP) Properties dialog
box and click OK again to close the Local Area Connection Properties
dialog box.
7
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
2. Access to Web Interface
1. Open a web browser. Type 192.168.1.222 in the address bar and then hit
Enter.
2. Login page will come up and you are required to enter username and
password. By default, the credentials are:
Username: admin
Password: admin
3. Click Login.
8
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
3. Configure AP Mode (2.4G/5G)
Network Scenario
1. Go to Configuration > Wireless > Radio0(2.4G)/Radio1(5G) > General.
Below screenshots show an example for 2.4G radio configuration only.
Same procedures can be applied to 5G radio configuration.
2. Make sure the box of Enable Radio is checked. Select AP mode for the
field of Radio Mode. Then click Submit.
3. Click WLAN and click More… in Detail of WLAN 0 to go to another page
for SSID and security configuration.
Internet
ISP
Modem
A2c (AP Mode)
Ethernet
Cable
2.4G + 5G
Coverage
Gateway/Router
Ethernet
Cable
Modem
Cable
9
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
4. Make sure WLAN is enabled by checking the box. Type in SSID to name
the wireless network you want to broadcast and then click Submit.
5. Click the tab WLAN Security. Select WPA2-PSK from the drop down menu
of Authentication Mode and select AES for Cipher Mode. Type in a
password within 8~64 characters or numbers in Pass Phrase and click
Submit.
6. Click Save & Apply at the top right corner to have all changes take effect.
7. Hook up the A2c as shown in Network
Scenario. The SSID should now be broadcast
from A2c and can be seen in the computer
for wireless connection.
10
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
4. Configure Gateway Mode (Router Mode)
Network Scenario
1. Follow the steps 1 –6 in Section 3 for the wireless settings.
2. Go to Configuration > Network > General.
3. Select Gateway Mode for Network Setting.
4. Select one of the following ways for Internet Connection Type. If you are
not sure about the connection options, consult your ISP for correct
settings.
(a) Static
Enter IP Address, Subnet
Mask, Default Gateway and
DNS Server IP Address as
provided by ISP.
Internet
ISP
Modem
A2c
(Gateway/Router Mode)
Ethernet
Cable
2.4G + 5G
Coverage
Modem
Cable
Table des matières
Autres manuels ALTAI Point d'accès sans fil
ALTAI
ALTAI A175FD Manuel utilisateur
ALTAI
ALTAI A2 Manuel utilisateur
ALTAI
ALTAI A2N Feuille d'instructions
ALTAI
ALTAI CX200 Manuel utilisateur
ALTAI
ALTAI A2 Feuille d'instructions
ALTAI
ALTAI A3 Series Manuel utilisateur
ALTAI
ALTAI IX500 Manuel utilisateur
ALTAI
ALTAI CX200 Manuel utilisateur
ALTAI
ALTAI AX500 Series Manuel utilisateur
ALTAI
ALTAI C2s Manuel utilisateur
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
