ALTAI C1N Manuel utilisateur
Altai Technologies Ltd. All rights reserved
ALTAI C1N SUPER WIFI CPE
INSTALLATION GUIDE
（）
Version 1.0
Date: September, 2013
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
Copyright © 2007 Altai Technologies Limited
ALL RIGHTS RESERVED.
Altai Technologies Limited
Unit 209, 2/F,
East Wing, Building 17,
Hong Kong Science Park,
Shatin, New Territories,
Hong Kong
Telephone: +852 3758 6000
Fax: +852 2607 4021
Web: www.altaitechnologies.com
Customer Support Centre:
Email: supp[email protected]
Radio Frequency Interference Requirements
This device complies with Part 15 of FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
3. This device should not be co-located or operating in conjunction with any
other antenna or transmitter.
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
This equipment generates uses and can radiate radio frequency energy. If it is not
installed and used in accordance with the instructions, harmful interference to radio
communications may be caused.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance,(example –use only shielded
interface cables when connecting to computer or peripheral devices) any changes
or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Warning
The user is advised to keep away from the base-station and antenna with at least
45cm when the base-station is in operation.
Please install a lightning arrestor to protect the base station from lightning dissipation
during rainstorms. Lightning arrestors are mounted outside the structure and must be
grounded by means of a ground wire to the nearest ground rod or item that is
grounded.
Disclaimer
All specifications are subject to changes without prior notice. Altai Technologies
assumes no responsibilities for any inaccuracies in this document or for any obligation
to update information in this document. This document is provided for information
purposes only. Altai Technologies reserves the right to change, modify, transfer, or
otherwise revise this publication without notice.
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
Contents
1. Introduction...............................................................................................................................5
2. Field Installation ........................................................................................................................5
2.1. System Configuration Requirements.................................................................................5
2.2. Introduction C1n Super WiFi CPE.......................................................................................6
2.3. Installing C1n Super WiFi CPE .............................................................................................7
2.4. Cable Connection ..............................................................................................................7
2.5. Desktop C1n Super WiFi CPE..............................................................................................8
2.6. Pole Mount C1n Super WiFi CPE ........................................................................................8
2.7. Wall Mount C1n Super WiFi CPE ........................................................................................9
2.8. C1n Waterproof Protection..............................................................................................10
3. Electrical Protection...............................................................................................................11
3.1. Grounding ..........................................................................................................................11
3.2. LAN Cable for Outdoor Installation.................................................................................12
3.3. ESD Protection....................................................................................................................12
3.4. Review the Installation ......................................................................................................13
4. Deployment Scenarios ..........................................................................................................13
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
1. Introduction
This guide is designed to provide the information needed to mount Altai C1n Super
WiFi CPE at the site location.
The document is applicable for hardware platform C1n and the following models.
Product name : Altai C1n Super WiFi CPE
It is assumed in this document that a site survey has been performed before the site
installation. The appropriate antenna pole and AP locations have been selected. It is
a good practice to have a document consists of a map and drawing illustrating the
AP and poles locations. A planning on IP network is also an important issue for
network planning.
The user may need to refer the following document during C1n installation and
Configuration.
[1] C1n Configuration Manual
[2] C1n Super WiFi CPE Data Sheet
2. Field Installation
2.1. System Configuration Requirements
Check the equipments and the installation kits against the packing list to ensure that
the equipment part numbers, parts, and the ancillary equipments included in the
shipment match what is specified on the packing list. The shipment consists of a C1n
Super WiFi Pico Access Point and an installation kit in the container. If there is any
difference from the packing list, you will need to contact the sales representative.
Please, inspect the equipment to see if there is any shipping damage. If it does have
any damage, you could contact the sales representative for repair or replacement.
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
Figure 2-1 C1n Package (UK Adapter)
Product:
C1n Super WiFi CPE x 1
Accessories:
AC Adapter x 1
DC Injector x 1
Table Stand x 1
Cable Tie x 2
Anchor and Screw x 2
Quick Installation Guide
2.2. Introduction C1n Super WiFi CPE
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
Figure 2-2 C1n Label
Remark: Grounding is recommended for outdoor installation
2.3. Installing C1n Super WiFi CPE
Before installation, please prepare the following tools:
1) Screw Driver (for wall mount)
2) RJ45 Shielded Connector Crimper
3) STP CAT5 Straight Cable x 2
4) Waterproof Sealing Tapes
5) Grounding Cable
2.4. Cable Connection
Figure 2-3 C1n Cable Connection Diagram
1. Connect C1n and DC injector with an Ethernet Cable
4
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
2. Connect another network cable between DC injector “LAN” port and a
computer Ethernet port
3. Connect the AC power adapter to the DC injector and plug it into a power
socket
4. Make sure both the Power LED and the Network LED light green
2.5. Desktop C1n Super WiFi CPE
Figure 2-4 C1n Desktop mount
1. Select the appropriated tilting angles: 8°and 23°
2. Change the C1n orientation to face the wireless target (base station or wireless
client)
3. Connect the LAN cable under the cable stand to the DC injector
2.6. Pole Mount C1n Super WiFi CPE
1
2
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
Figure 2-5 C1n Pole Mount
1. Use 2 wire clamps to mount on the pole with diameter about 25mm (1 inch).
2. Change the C1n orientation to face the wireless target
2.7. Wall Mount C1n Super WiFi CPE
Figure 2-6 C1n Wall Mount
Altai Technologies Ltd. All rights reserved
Altai C1n Super WiFi CPE Installation Guide
TPS13-002_rev1.0
1. Drill two holes with separation by 60mm (2.3 inches)
2. Install the anchors on the holes and screw into the wall with 10mm (0.4 inch)
extension.
3. Put the C1n onto the screw.
2.8. C1n Waterproof Protection
Especially for outdoor installation, waterproof protection can enhance the protection
from water leakage. Both the LAN cable and the unit should be wrapped.
Figure 2-7 Cable Wrapping
1. Wrap the cable with a layer of rubber tape. Start from 5cm below the connector.
Wrap a loop and overlap a half. Continue until it reaches under the connector.
Figure 2-8 First Layer-Rubber Tape
Autres manuels pour C1N
2
Table des matières
Autres manuels ALTAI Matériel réseau
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
