ALLOMATIC SW-300DC Manuel utilisateur
®
UL325
compliant
compliant
UL991
L
I
S
T
E
D
®
US
SW-300DC Installation Manual
Copyright © 2008 all-o-matic inc. www.allomatic.net
WWW.ALLOMATIC.NET
Pending
TABLE OF CONTENTS
Important safety instructions........................................................
Different UL 325 class types.............................................................
Concrete pad Specs.........................................................................
Operator & Arm Layout..............................................................
Compact Installation.........................................................................
Torque limiter & Arm adjustment......................................................
Gate travel adjustment.....................................................................
Directional settings..........................................................................
Electrical power connections...........................................................
Typical loop layout...........................................................................
General loop installation guidelines...............................................
Accessory connections...................................................................
Multiple safety device connections.................................................
Plugin detector installation..............................................................
Leading edge installation.................................................................
Three button station........................................................................
Master/Slave connections...............................................................
Magnetic/Solenoid lock installation.................................................
Radio receiver hookup....................................................................
Open & Close electronic reversing sensor(ERD) adjustment.........
Timer adjustment............................................................................
Dip switch functions........................................................................
Solar panel installation...................................................................
Swinger arm parts..........................................................................
2&3
4
5
6,7&8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of
WARNING
injury:
READ THE FOLLOWING DIRECTIONS. DO NOT EVEN THINK OF STARTING UNTILYOU HAVE
READ AND UNDERSTAND THESE DIRECTIONS. IF THERE IS SOMETHING YOU DO NOT
UNDERSTAND CALL US.
let children operate or play with gate controls. Keep the remote control away from children.
Always keep people and objects away from the gate. No one should cross the path of the moving gate.
This operator must be tested monthly. The gate must reverse on contact with a ridged object or stop
when an object activates the non-contact sensors. After adjusting the force or the limit travel, retest the
gate operator. Failure to adjust and retest the gate operator properly can increase the risk of injury.
Keep gates properly maintained. Have a qualified service person make repairs to gate hardware. It
takes many years of experience to make proper adjustments to gate hardware or operators.
There is nothing on a gate operator that is easily repaired without a great deal of experience. Save
yourself some time and call a qualified Gate Service Contractor who knows your type of gate operator.
Never
2
*Confirm that the gate operator being installed is appropriate for the application.
*Confirm that the gate is designed and built according to current published industry standards.
*Confirm that all appropriate safety features and safety accessory devices are being incorporated, including both primary and secondary
entrapment protection devices.
*Make sure that the gate works freely before installing the operator.
*Repair or service worn or damaged gate hardware before installation of the operator.
*Eliminate all gaps in a sliding gate below a 4 foot height that permits a 2 ¼ inch sphere to pass through any location, including the area
of the adjacent fence covered when the gate is in the open position.
*Eliminate all gaps in a swinging gate below a 4 foot height that permit a 4 inch sphere to pass through any location, including the hinge
area of the gate.
*Operator must be disconnected from the power source before attempting any installation of accessories.
*Install this gate operator according to our installation instructions.
*Adjust the operator clutch or load sensing device to the minimum force setting that will still allow for reliable gate operation.
*Install the operator inside the fence line(do not install the operator on the public side of fence line).
*Install a proper electrical ground to a gate operator.
*Install controls where users cannot touch or reach through the gate to operate the controls.
*Install all warning signs and take pictures of the installation.
*Test all safety features for proper function before placing the automatic vehicular gate into service.
*Train owner/users about basic functions and safety features of the gate system, including how to turn off the power and how to operate
the manual disconnect feature.
*Leave safety instructions, product literature, installation manual and maintenance manual with end user.
*Explain to the owner/user the importance of routine service and retesting on a monthly basis.
INSTALL THE GATE OPERATOR ONLY WHEN YOU HAVE READ THE
FOLLOWING:
3
Class one: Residential
A vehicle gate operator intended for use at a home of one to four single family dwellings, garages or parking area.
Class Two: Commercial or General Public Access
A vehicular gate operator intended for use at a commercial location or building such as a multi-family housing unit (five or more single
family units), hotel, garages, retail stores, other buildings servicing the general public.
Class three: Industrial or limited Access
A vehicular gate operator intended for use at an industrial location or building such as a factory, loading dock area, or other locations not
intended to service the general public.
Class Four: Restricted Access
A vehicular gate operator intended for use at a guarded industrial location or building such as airport security areas or other restricted
access locations not servicing the general public where unauthorized access is prevented via supervision by security personnel.
Other components required to satisfy UL 325
Each class must have a primary and secondary means to sense and react to obstructions within two seconds.
The six types of obstruction sensing systems are:
Type A:
Inherent obstruction sensing system. This system must sense and initiate the reverse of the gate within two seconds of contact with a
solid object.
Type B 1:
Provision for connection of a non-contact device can be used, such as a secondary protection.
Type B2:
Provision for connection of a contact sensor. Examples include an edge device or equivalent. This can be used for secondary protection.
Type C:
Inherent adjustable clutch or pressure relief valve.
Type D:
Provision for connection of or provided with and actuation device requiring continuous pressure.
Type E:
Inherent audio alarm.
All of All-O-Matic Inc’s Gate operators conform to the most ridged Class One.
DIFFERENT UL 325 CLASS TYPES
4
CONCRETE PAD FOR SW-300
24”
24”
24”
9.5”
13.5”
4”
OO
UU
RR
NN
33
88
66
BB
SS
33
1133
OO
UU
RR
NN
33
88
66
BB
SS
33
1133
OO
UU
RR
NN
33
88
66
BB
SS
33
1133
1 2 3 4 5 6 7 81 2 3 4 5 6 7 8
-----------------------OPEN-----------------------------------------------OPEN------------------------
PHILIPSPHILIPS
P87C554SBAAP87C554SBAA
Cd2399Cd2399
TIG0505ATIG0505A
PHILIPSPHILIPS
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
ONON 514514
GDEGDE
00uF00 uF 2200 uF2200 uF 2200 uF2200 uF 2200u2200 u
23” 25.5”
Operator plastic
Cover
Operator frame
1/21/2
Four red head
Bolts ””
X 3
Area for Conduit(s)
Operator Concrete
Pad
When possible
Install 4” above
Ground
Footing for
Gate operator Master/Slave
Single Conduit for
Low voltage
High voltage
conduit
5
OPERATOR AND ARM DIMENTIONS
2” B
OUTSIDE
INSIDE
POST
CONCRETE PAD
Minimum
distance
Dimentions Chart
Gate
length A B C Minimum
Distance
Less than
12”
13’-15’
16’-22’’
36”
37”
34”
40”
35”
42” 14”
14”
14”
41”
48” 47”
This distance is from
the gate in open
position to edge of the
pad. Refer to .note
Note: The 2” distance shown above is from the gate in the open position to the edge of the pad.
If the gate must open more than 90 degrees, the pad needs to move back accordingly. The
distance between the open gate and the pad needs to remain 2”. The distance “C” also needs to
move back accordingly if the opening is more than 90 degrees.
A
C
IM
PR ARY
E ON A
SC D RY
HINGE
CENTER
Refer to
below.
note
A: Is the distance between the gate bracket and the gate
hinge point.
B: Is the distance between the gate hinge point and the edge
of the concrete pad.
C: Is the distance from the gate in the open position to the center
shaft of the operator.
Minimum distance: Is the minimum distance required behind
the open gate. If the distance between the
open gate and the back wall is between 20”
and 33” refer to compact installation.
6
X
X
Hinge point
Hinge point
Bracket
Bracket
Bracket
Bracket
Mark ground under
gate bracket with
gate closed. This will
be point Y
Mark ground under
gate bracket with
gate open. This will
be point Z14”
“A”
Center shaft of
Operator
1
2
X
X
Point Y
Point Y
Point Z
Point Z
Out
In
Out
In
OPERATOR AND ARM LAYOUT
Draw a line from point past
the point as shown. This
should be laid on the ground.
The operators center shaft goes
on this line.
Y
Z
7
ARM LAYOUT & OPERATOR PLACEMENT CONTINUED
Hinge point
Bracket
Bracket
Center shaft of
Operator
3
Measure distance from the
YZ.
point
And point Say distance is 60”,
divide this number by 2,which
=30”. This is the length of primary
PLEASE BE EXACT!!!
4
++
This ARM section is half the distance
between point and point as shown
above. Y Z
IT MUST BE EXACT!!!
This pipe does not need to be
measured after primary arm is
installed this pipe makes up the
balance of arm.
RAY M E
PIM R ARS CTION
CENTER OF
BOLT AT FIRST
HINGE POINT
CENTER OF
SHAFT ON
OPERATOR
X
X
Point Y
Point Z
8
SWINGER COMPACT
INSTALLATON
OUTSIDE
INSIDE
20” Minimum
8”
35”
CO AY
SE ND R
HINGE
CENTER
27”
20”
Use these measurements, only if the
distance between the wall and the
gate in the open position is 20” to 34”.
If you have more than 34” refer to
standard installation.
To use this installation the gate must be 12’ or less.
9
Table des matières
Autres manuels ALLOMATIC ouvre-porte
ALLOMATIC
ALLOMATIC TORO 24 PRIME Manuel utilisateur
ALLOMATIC
ALLOMATIC TORO 24 Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-175 Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-100AC Manuel utilisateur
ALLOMATIC
ALLOMATIC SW-350DC Manuel utilisateur
ALLOMATIC
ALLOMATIC TORO 24 Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-100 AC Manuel utilisateur
ALLOMATIC
ALLOMATIC TORO 24 Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-175DC Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-90DC Manuel utilisateur
