ALLOMATIC OH-200DC Manuel utilisateur
1
®
A
T
E
G
O
C
P
I
E
T
R
A
A
M
T
O
O
T
R
U
S
A
A
T
E
G
O
C
P
I
E
T
R
A
A
M
T
O
O
T
R
U
S
A
A
T
E
G
O
C
P
I
E
T
R
A
A
M
T
O
O
T
R
U
S
A
S
L
S
I
D
D
A
E
E
R
S
H
R
•
E
S
V
W
O
I
N
•
G
S
E
R
S
L
S
I
D
D
A
E
E
R
S
H
R
•
E
S
V
W
O
I
N
•
G
S
E
R
S
L
S
I
D
D
A
E
E
R
S
H
R
•
E
S
V
W
O
I
N
•
G
S
E
R
OH-200DC Installation Manual
Copyright © 2016 all-o-matic inc. www.allomatic.net
WWW.ALLOMATIC.NET
UL-325 6th edition,
UL-991 & CSA C22.2
#247 Compliant
2
TABLE OF CONTENTS
SAFETY AND INTRODUCTION
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
UL 325 Cass Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operator Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLATION
Operator Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operator Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Entrapment Protection Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Loop Layout................................................11
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Gate Travel Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
BOARD FEATURES
Gate Opening Direction Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programmable Relay and Leaf Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Electronic Reversing Device (ERD) Adjustment . . . . . . . . . . . . . . . . . . . . 16
Timer Adjustment and Radio Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Dip Switch Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LED Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
WIRING ACCESSORIES TO CONTROL BOARD
Accessory Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Monitored Entrapment Protection Device Connection . . . . . . . . . . . . . 21-22
Loop Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Three-Button Station Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Radio Receiver Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SOLAR INSTALLATION
Solar Panel Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
External Solar System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
BREATHER CAP PIN.............................................28
EMERGENCY RELEASE INSTRUCTIONS............................29
WARRANTY AND CUSTOMER RECORD.............................30
PARTS BREAKDOWN
OH-200 DC Blowout Drawing . . . . . . . . . . . . . . . . . . . . . . . . Check Website
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF :INJURY
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. DO NOT START INSTALLATION UNTIL
YOU HAVE READ AND UNDERSTAND THESE DIRECTIONS. IF THERE IS SOMETHING YOU DO NOT
UNDERSTAND, PLEASE CALL US.
NEVER let children operate or play with gate controls.
Locate the control station and make sure it is (a) within sight of the gate and (b) at a minimum height of 5
feet so small children cannot reach it.
Install the enclosed entrapment warning signs next to the control station and in a prominent location.
For operators equipped with a manual release, instruct the end user on the correct operation of the manual
release. Use the manual release only when the gate is not moving. It is advised that the power be turned
off.
Always keep people and objects away from the gate. No one should cross the path of a moving gate.
The gate operator must be tested monthly. The gate must reverse on contact with a rigid object, or stop
when an object activates the non-contact sensor(s). Always re-test the operator after adjusting the limits
and/or force. Failure to adjust and re-test the gate operator properly may cause sever injury or death.
Keep gate(s) properly maintained. Have a qualified service technician make repairs to gate hardware and
make proper adjustments to gate operator.
This gate entrance/exit is for vehicles only. Pedestrians must use a separate entrance.
There is nothing on a gate operator that is easily repaired or adjusted without a great deal of experience.
Call a qualified gate service technician who knows your gate operator.
SAVE THESE INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)
BEFORE GATE OPERATOR INSTALLATION
ŸConfirm that the gate operator being installed is
appropriate for the application.
ŸConfirm that the gate is designed and built
according to the current published industry
standards.
ŸConfirm that all appropriate safety features and
safety accessory devices are being installed,
including all entrapment protection devices.
ŸMake sure that the gate opens and closes freely
(by hand) before installing the operator.
ŸRepair or replace worn or damaged gate
hardware before installing the gate operator.
ŸEliminate all gaps in the sliding gate below a 6
foot height that permits a 2 1/4” sphere to pass
through any location. This includes the area of
the adjacent fence covered when the gate is in
the open position
ŸEliminate all gaps in a swing gate below a 4 foot
height that permits a 4” sphere to pass through
any location. This includes the hinge area of the
gate.
GATE OPERATOR INSTALLATION
ŸOperator must be disconnected from the power
source before attempting any installation of
accessories.
ŸInstall gate operator according to the installation
instructions in this manual.
ŸAdjust the operator clutch or load sensing device
to the minimum force setting that will allow for
reliable gate operation.
ŸInstall the operator inside the fence line. Do not
install the operator on the public side of the fence
line.
ŸInstall a proper electrical ground to the gate
operator.
ŸControls intended for user activation must be
located at least 6 feet away from any moving part
of the gate, and where the user is prevented
from reaching over, under, around, or through
the gate to operate the controls.
ŸOutdoor or easily accessible controls shall have
a security feature to prevent unauthorized use.
ŸThe stop and/or reset button must be located in
the line of sight of the gate. Activation of the
operator reset control shall not cause the
operator to move.
ŸInstall a minimum of 2 warning signs, one on
each side of the gate where they are easily
visible.
ŸTake pictures of the installation.
ŸTest all safety features for proper function before
placing the automatic vehicular gate in
operation.
MAINTENANCE
ŸTrain owners/users on the basic functions and
safety features of the gate system, including
how to turn off the power and operate the
manual disconnect feature.
ŸLeave safety instructions, product literature,
installation manual, and maintenance manual
with the owner or end user.
ŸExplain to the owner or end user the importance
of routine service and operator testing on a
monthly basis.
INSTALL THE GATE OPERATOR ONLY WHEN YOU
HAVE READ THE FOLLOWING
5
UL 325 CLASS TYPES AND OBSTRUCTIONS SENSING SYSTEMS
UL 325 CLASS TYPES
CLASS ONE: RESIDENTIAL
ŸA vehicular gate operator intended for use in
garages or parking areas associated with a
residence of one to four single families.
CLASS TWO: COMMERCIAL OR GENERAL
PUBLIC ACCESS
ŸA vehicular gate operator intended for use at a
commercial location or building, such as a
multi-family housing unit (five or more single
family units), hotel, garages, retail stores, or
other buildings accessible by or servicing the
general public.
CLASS THREE: INDUSTRIAL OR LIMITED
ACCESS
ŸA vehicular gate operator intended for use at
an industrial location or building, such as a
factory, loading dock area, or other locations
not accessible by or intended to service the
general public.
CLASS FOUR: RESTRICTED ACCESS
ŸA vehicular gate operator intended for use at a
guarded industrial location or building, such as
airport security areas or other restricted
access locations not servicing the general
public and where unauthorized access is
prevented via supervision by security
personnel.
THE SIX TYPES OF OBSTRUCTION
SENSING SYSTEMS
TYPE A:
ŸInherent entrapment protection system. This
system must sense and initiate the reverse of
the gate within 2 seconds of contact with a
solid object.
TYPE B1:
ŸNon-contact sensor (photoelectric sensor or
equivalent). This system shall, upon sensing
an obstruction in the direction of the gate
travel, reverse the gate within a maximum of 2
seconds.
TYPE B2:
ŸContact sensor (edge device or equivalent).
This system shall, upon sensing an obstruction
in the direction of the gate travel, initiate the
reversal of the gate within a maximum of 2
seconds.
TYPE C:
ŸInherent force limiting, inherent adjustable
clutch, or pressure relief valve.
TYPE D:
ŸActuating device requiring continuous pressure
to maintain opening or closing motion of the
gate.
Each class must have (2) monitored entrapment protection devices in each entrapment zone to sense and react
to obstructions within 2 seconds.
All-O-Matic’s gate operators conform to the most rigid Class One.
6
OPERATOR SPECIFICATIONS
Max Gate Weight
800 lbs.
Max Gate Length
22’
Warranty
5 year commercial
Motor
24 VDC brushless
1/2 HP equivalent
Gate Speed
Approximately 15 seconds per opening
6.5’ - 8’ high gate
Power
115 VAC single phase - 6 amps
230 VAC single phase - 3.5 amps
or 24 VDC solar panel up to 80 watts
Duty Cycle
Continuous
Temperature Range
-40º to 160º
Gear Box Ratio
40:1
Dimensions
13” W X 144” L X 8” H (Custom rail lengths available)
Shipping Weight
110 lbs.
Emergency Release
Lockable quick release drive arm and carriage
Belt Size
4L-200
Main Sprocket
41B15 x 5/8” bore
Chain Size
41NP
Gear Box Sprocket
N/A
Limit Shaft Sprocket
N/A
Breaker Requirement
20 amp dedicated
Gearbox Pulley
2.5” with 1/2” bore
Motor Pulley
2” with 5/8” bore
UL Classes
I, II, III & IV
OH-200 DC
7
OPERATOR DIMENSIONS
15’’
18’’
13’’ 8’’
144’’
22’’
2 5/8’’’
6 1\4
4 1\2
8’’
Custom track length
(up to 16 ft) available
upon request.
8
OPERATOR INSTALLATION
+
+
With gate closed, mark the center of the gate.
Lift gate to open position and mark the center point of the gate for the operator on the ceiling.
Note: Make sure the gate hardware is well balanced. The gate should open and close smoothly.
9
MOUNTING INSTRUCTIONS
Make sure the end bracket is in the center of the
opening. Bolt or weld the end bracket to wall.
The operator bracket must be at least 2.5”
above the gate.
+
Level and align the gate operator tracks before
mounting them to the ceiling. Manufacture ceiling
brackets to weld or bolt the operator in place (not
provided).
Connect the overhead arm, insure alignment,
and weld the gate bracket in place.
+
WELD
BOLT
CENTER
OVERHEAD ARM
GATE BRACKET
CENTER
CONCRETE ANCHOR
½”X 3 ½”
10
ENTRAPMENT PROTECTION INSTALLATION
SIDE VIEW
ŸA minimum of (2) monitored entrapment protection devices are REQUIRED for each entrapment zone.
ŸAn entrapment zone is a location or point of contact where a person can become entrapped between a moving
gate and a rigid object.
ŸThe operator is equipped with an inherent entrapment protection system (ERD).
ŸThe gate operator requires an external monitored entrapment protection device (non-contact photoelectric
sensor or contact edge) for each entrapment zone prior to gate operation. The operator cycles power to the
external entrapment protection device and checks for device signals. If the operator does not receive the
correct feedback from the device, the gate will not operate.
PHOTOELECTRIC SENSOR FOR CLOSE CYCLE
OUTSIDE PROPERTY LOOKING IN
EDGE SENSOR FOR OPEN
CYCLE. INSTALL HORIZONTALLY
ON BOTTOM AND/OR FRONT
OF GATE FRAME
Table des matières
Autres manuels ALLOMATIC ouvre-porte
ALLOMATIC
ALLOMATIC SW-300DC Manuel utilisateur
ALLOMATIC
ALLOMATIC TORO 24 Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-100 AC Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-45DC Manuel utilisateur
ALLOMATIC
ALLOMATIC DC Series Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-175DC Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-90DC Manuel utilisateur
ALLOMATIC
ALLOMATIC TORO 24 Manuel utilisateur
ALLOMATIC
ALLOMATIC TORO 24 PRIME Manuel utilisateur
ALLOMATIC
ALLOMATIC SL-100AC Manuel utilisateur
