Allegion LCN 8310-852WP Manuel utilisateur

75.5316.01 ALLEGION WIRELESS PUSH PLATES 20180702 Page 1 of 4

DESCRIPTION

1. Hex Key

2. Housing Assembly

3. Faceplate

4. Locking Tab

5. Mounting Bracket

6. Battery Enclosure

7. Mounting Keys

8. Mounting Holes

6” ROUND

8310-852TWP (shown)

8310-852WP (not shown)

4.5” SQUARE

8310-853TWP (not shown)

8310-853WP (shown)

8310-852WP/853WP WIRELESS PUSH PLATES

Wireless, stainless steel actuator switches

(US version)

ENGLISH

Page 2 of 4 75.5316.01 ALLEGION WIRELESS PUSH PLATES 20180702

TROUBLESHOOTING

No activation Receiver not programmed Setup transmitter

Receiver improperly wired Verify power and activation connection

Dead battery Replace battery

Constant activation Battery Housing screws too tight Loosen Battery Housing screws

Connected to door control with

NC terminal

Use NO terminal

Receiver set to Toggle Mode Set receiver to Pulse Mode

INSTALLATION

To program the wireless receiver (sold separately), please refer to the appropriate 433 MHz Wireless

Transmitters & Receivers User’s Guide (75.5315).

Install Mounting Bracket using at least two (2)

#8 countersunk head screws1. Any mounting

holes may be used. Observe “THIS END UP”.

Align Housing Assembly onto Mounting

Keys and slide down until Locking Tab

engages. To remove, press Locking Tab

and slide up.

Insert Faceplate into Housing Assembly and

use Hex Key to engage spring clips on the

top and bottom of Housing Assembly2. To

remove, use Hex Key to disengage spring clips.

Remove four (4) screws on Battery Enclosure.

Replace with one (1) 12V Type A23 battery.

DO NOT OVER TIGHTEN SCREWS DURING REASSEMBLY.

THIS MAY CAUSE CONSTANT TRANSMITTER ACTIVATION.

Remove Housing Assembly from Mounting

Bracket by pressing in on locking tab and

sliding up.

NOTES:

1. For added security, additional screws may be installed through Housing Assembly and Mounting Bracket.

2. Ensure spring clips “click” during Faceplate installation. It may be necessary to rotate Faceplate for proper alignment.

75.5316.01 ALLEGION WIRELESS PUSH PLATES 20180702 Page 3 of 475.5316.01 ALLEGION WIRELESS PUSH PLATES 20180702 Page 3 of 4

FCC ID: 2ABWS-10TD900PTRI IC: 4680-10TD900PTRI

MODEL: 10EMR61-900 MODEL: 10EMR4751-900 MODEL: 10EMS4751-900

MODEL: 10EMR6-900 MODEL: 10EMR475-900 MODEL: 10EMS475-900

MODEL: 10EMR6L-900 MODEL: 10EMR475L-900 MODEL: 10EMS475L-900

FCC ID: 2ABWS-10TD433PTRII IC: 4680-10TD433PTRII

MODEL: 10EMR61 MODEL: 10EMR4751 MODEL: 10EMS4751

MODEL: 10EMR6 MODEL: 10EMR475 MODEL: 10EMS475

MODEL: 10EMR6L MODEL: 10EMR475L MODEL: 10EMS475L

TECHNICAL SPECIFICATIONS

Dimensions: 6” ROUND - 6.33” diameter, 1.45” depth

4.75” SQUARE - 5.12” height, 5.12” width, 1.42” depth

Weight: 6” ROUND - 1.2 lbs

4.75” SQUARE - 1.04 lbs

Material: FACEPLATE - stainless steel

HOUSING - ABS plastic

Transmitter frequency: 433 MHz

Power: 433 MHz versions - one (1) 12V Type A23

Mounting: Surface mount only

Certiﬁcation: FCC, IC

Temperature: 14 °F - 131 °F (-10 °C - 55 °C)

Enclosure rating: NEMA 4

FCC / IC

“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.”

Changes or modiﬁcations not expressly approved by BEA Incorporated could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

75.5316.01 ALLEGION WIRELESS PUSH PLATES 20180702

Do not leave problems unresolved. If a satisfactory solution cannot be achieved after

troubleshooting a problem, please contact Allegion at 1-877-671-7011. If you must wait for

the following workday to call Allegion, leave the door inoperable until satisfactory repairs can

be made. Never sacriﬁce the safe operation of the automatic door or gate for an incomplete

solution.

For more information, visit www.allegion.com.

PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING

| Original Instructions

The sensor manufacturer cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor/device; therefore, the sensor

manufacturer does not guarantee any use of the sensor outside of its intended purpose.

The sensor manufacturer strongly recommends that installation and service technicians be AAADM-certiﬁed for pedestrian doors, IDA-certiﬁed for

doors/gates, and factory-trained for the type of door/gate system.

Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor