ALGE-Timing Timy SPEED Manuel utilisateur
E-05-08-29
Timy
SPEED
Timy SPEED
Seite 2
Table of Content
1Keypad and implementing........................................................................................................ 3
2Description of display indication............................................................................................. 3
2.1 Startnumber and STN-automatic................................................................................................. 3
2.2 Adjustments in subprogram SPEED ........................................................................................... 3
2.2.1 Distance................................................................................................................................... 4
2.2.2 Directions................................................................................................................................. 4
2.2.3 Unity......................................................................................................................................... 4
2.2.4 min. speed...............................................................................................................................4
2.2.5 max. speed.............................................................................................................................. 4
2.2.6 Print times................................................................................................................................4
3Connection of the photocells................................................................................................... 5
Technical changes reserved in sense of improvement!
ALGE Timy manual copyright by:
ALGE-Timing GmbH & Co
Rotkreuzstraße 39
A-6890 Lustenau
www.alge-timing.com
Tel: 0043 – 5577 – 85966
Fax: 0043 – 5577 – 85966-4
Timy SPEED
1 Keypad and implementing
Please see Timy manual „GENERAL“ .
2 Description of display indication
Description of settings:
Startnumber and startnumber-automatic
Measured speed
Adjusted distance
Speed unity
Measuring-direction
If the start-photocell is triggered out, the display will show instead of “0.00” a dotted line.
Timy will calculate from the adjusted distance and min. speed, how long one cycle will take at
maximum. If this time will be crossed, the display will show “0.00” and is ready for the next
measurement.
2.1 Startnumber and STN-automatic
Here you can adjust the requested start number. You should always confirm it with one of the
“OK” buttons. You can use the same startnumber for several times.
The startnumber-automatic can be adjusted at “Main menue”, “General”, “STN-automatic”.
Arrow upward means that the startnumber will increase for one number.
Arrow downward means that the startnumber will decrease for one number.
If no arrow is visible then the automatic is deactivated.
2.2 Adjustments in subprogram SPEED
Here you can adjust and change several setting which will also be indicated at the display
Push the button . Push the buttons or as long as you will see menue point
„SPEED“. You can make adjustments at the following points:
distance
direction
unity
min. speed
max. speed
print times
Seite 3
Timy SPEED
Seite 4
2.2.1 Distance
Here you should indicate the distance to the mounted photocell before.
ATTENTION! Only distances without decimal place.
Confirm the indicated distance with one of the two „OK“-buttons.
2.2.2 Directions
You can chose between three settings:
C0 < -- > C1 Measuring from both directions possible
C0 -- > C1 Measuring only of direction Start RLS (green cable or C0)
C1 -- > C0 Measuring only of direction Stop RLS (red cable or C1)
2.2.3 Unity
Here you can adjust the unity of the speed:
km/h kilometer per hour
mp/h miles per hour
m/s meter per second
2.2.4 min. speed
In this program you can adjust the minimum speed for a valid measurement.
2.2.5 max. speed
In this program you can adjust the maximum speed for a valid measurement.
2.2.6 Print times
If it is adjusted to „OFF“, it will print only the startnumber and the speed.
If it is adjusted to „ON“, it will print additionally start- and finish-time as well as the run time.
Timy SPEED
3 Connection of the photocells
There are several possibilities the connect the photocells to a Timy.
Since the Timy has just one photocell-plug, you have to use an adapter if the photocells
should be supplied by the Timy.
adapter 018-- 3 plugs for RLS
adapter cable 160—2 2 plugs for RLS
The photocells can also be connected to the Timy with help of a double-pole cable. But then,
you will require batteries for the photocells. Then you have got the advantage, that the
batteries or accus of the Timy won’t be empty that fast.
Of course, you can also mix these two versions. Pay attention to the fact that the startcable
(002-xx) and plug C1 or the stopcable (001-xx) and plug C0 will be used.
Seite 5
Autres manuels pour Timy SPEED
1
Table des matières
Autres manuels ALGE-Timing Instrument de mesure
ALGE-Timing
ALGE-Timing OPTIc2 Manuel utilisateur
ALGE-Timing
ALGE-Timing Timy Commander Manuel utilisateur
ALGE-Timing
ALGE-Timing Speedy 150-3-R Manuel utilisateur
ALGE-Timing
ALGE-Timing Photocell PR1aW Manuel utilisateur
ALGE-Timing
ALGE-Timing Timy SPEED Manuel utilisateur
ALGE-Timing
ALGE-Timing Windspeed WS2 Manuel utilisateur
ALGE-Timing
ALGE-Timing Photocell PR1a Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur